I started with a Left side view of a part and created a sectioned view right down the middle so you can see the insides from another view. the part is pretty big so i used a Break to shorten it to fit the page. I also placed a smaller and separate isometric view of the same part and want this view to inherit the same break. How can I do this? If I go into the display options of the iso view, all the cut inheritance options are grayed out and can't be clicked. I've seen this done before, but i'm sure i missed a step somewhere.
Inventor Professional 2013 Intel Xeon W3680 @ 3.33Ghz 12GB DDR3 RAM NVIDIA Quadro 2000 GPU Windows 7 Professinal 64-bit
Sometimes when I try to create a detail view of an isometric view in my IDW, the "detail full boundary" option is greyed out? Why would this be? If I try an ortho view it works fine.
I have a view of an assembly where I used a break out to break through a part. I want to make a section of this, and have that view respect that the part was broken and show it as broken in the new view.
The section view shows the full part 100% unbroken. In the edit view, the only option for cut inheritance is "break". All others are greyed out.
Why I want to do this: I am unable to break it in the section view because there is no option to break through a single part a specified distance. I cannot break an area "from point" or "to sketch" because they don't let you choose a single part for the effect, and the parts completely included in the break out this way are not going to show up in the parts list, so you cannot adjust their section participation, therefore I also cannot just break an area and then choose what parts don't get the effect.
I have made an exploded view and placed it an a drawing. I would like to view inside one of the bodies to show where the exploded internals sit, however when I do a break out of the body the trail lines from the exploded internals also get sectioned. Is there a way to control the sectional properties of a trail line?
I use: oView.scale=oView.scale/2 to half each view scale. It works for base view, projected views like bottom view and left view, but it doesn't work for Isometric view. Which property should I use for Isometric view?
Trying to dimension a shaft in isometric view with various diameters. I am unable to find or select the centerpoints at the ends of the shaft. This causes dimensions to be crooked. How can i get the centerpoints to display so that they may be selected?
1. I had trouble with profile view of the alignment line shown. What step am i missing? Are there things that is turned off?
2. How can I best come up with the right volume to fill.
3. Do I need to learn the grading tools? or could i get buy with a section profile from the alignment. ( it is not even an alignment yet)
4. How to I render a rock fill in this cave-in.
The attached aerial image , has survey or cogo points that are imported to surface, to become surface points. . So I wanted to create a surface profile below and an outline of fill above it. Iideally the side profile would look like a trapezoid, where the base is the surface proile and top would be the design embankment.
But the reason , a surveying crew went down and took shots at the shoreline and a couple shots around the cave-in walls (higher elevation on the cave-in wall cannot be surveyed, although I coud have used a laser , did not) is so that a more accurate volume of the cave in can be obtained. I tried to label how far the road edge is from edge of the cave-in . Norice the higher elevations are the top edge around the cave in area.
The ouline for the embankment will be a mild slope then breaks to a more steep slope. like 4 :1 , then 1.5:1
I am trying to make section views from the parent view. I need to make several section view, but there is not enough room on one sheet for all of them. Is there a way to move or copy the section views to different sheets and keep the connection for when chages are made all views will update?
When making a Section view from a Base View is there a setting to make the text follow the Text Style and Paperspace text size. Everytime I create a Section View I have to change the text settings in the Properties box.
I order not to hide components, i want to make a break sketch and remove a piece from a part from an assembly in the isometric view in a drawing. can i do that?
I need an urgent solution to my issue.I have created section view from a sketch (a line constrained to the projection of a work plane) from my derived part to my drawing using the "Get model sketches ". When i update the iassembly and update the the view using model state the view tries to update but throws an error see attached document.When i delete the section line and create a section line manually ie. by creating a normal sketch in the drawing the same model gets updated without any error.
When creating a section view in 2014, the new view now comes bordered by a large box that is hatched. I can hide the borders (4 separate lines) and the hatch but cannot change the size of the view border. I don't remember this from 2011.
I am trying to produce a section view of a vessel. Inventor makes the section just fine except it is incomplete. See images below:
In the past when I have encountered this issue I would simply locate the part in the browser, Right click on it + Section Participation + section. That usually solves the issue. This time it is not working.
While sectioning an assembly in .idw file, I dont want to see any thing that is behind the section line.
I am not talking about hidden lines. (I can switch of the hidden lines).
Some times, there are holes or opening while sectioning. Thru those openings, some of the parts that are behind the section planes are visible. I dont want to see anything.
How to do it? I am using INV2013.
Options like,
Option 1: Dont view anything more then 0.00mm or 1 mm behind. (Like section depth or view depth which can be entered)