I am using Inventor 2012 and have recently experienced a problem with the fillet not working correctly. I have a curve and a straight line that connect and when I select fillet it will allow me to select the curve but not the straight line. I have been able to do this in the past with no problems.
View 4 RepliesI know about the pink lines, green lines, and black line, but I recieved a part from another person and it had red lines for the sketch, how, what did he do to get those? He doesn't know how he did it.
View 8 Replies View RelatedIs there any way to make 2 to sketch lines instead of floating lines so that I can dimension them?
For example, if I have a part that can change lengths and I need to print off a new drawing, it would be good if I could say that the lines were a set distance from each end of the part or some features of the part.
Then I could update the part length, then just open the part drawing and not have to adjust anything.
Likely a simple question; I have completed a part and because I am new, drew it a certain way to make my life easier. Now that the part is complete I would like to rotate the entire part (but not create a new solid) by 45 deg.
Inventor 2014 PDS
Is it possible to disable that green "Finish sketch" and Ok button when your in sketch mode drawing with a Spline?
View 4 Replies View RelatedAutodesk for Inventor 2013, the ability to save while in sketch mode - if you're going to be spending a lot of design time sketching then this needs to be addressed so that the drawing is automatically saved. Otherwise if Inventor crashes (which it often does) while you're busy sketching away you loose your work.
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
How do I get rid of the yellow dot behind the cursor in sketch mode?
View 2 Replies View RelatedIs it possible to use the ""Centerline Bisector" command in the sketch enviroment. I want to add a centerline of a hole on a sketch on my part, but I only want to select two lines and have the centerline generated.
View 3 Replies View RelatedHow does one (in sketch mode) dimension from the quad of a circle instead of the center? Been dealing with it for a long time, no I am fed up and want to dimension from the quad.
View 6 Replies View RelatedInventor 2010
Some how I turned off the snap to end point in the sketch mode. where is the dialog box to control snap settings
In 5.3 I can create reference dimensions in sketch mode to my hearts content. They became very valuable as I would use them to determine placement of multiple features. Now, in IV 7, I have alot of trouble creating reference dimensions from adjacent features on the same surface. I have to change the way I'm working now and it has stumped me on a few occasions. is there a "new" feature I need to enable or is this the cost of progress?
View 9 Replies View RelatedI wonder if one can use drive constraint in sketch mode for blocks as I like to visualise how the links move when one dimension changes.
View 4 Replies View RelatedHow do I change the dimension size in sketch mode?
View 4 Replies View RelatedSometimes when I'm exiting from a sketch, the entire model goes back to isometric view. Is there a way to STOP this from happening?
View 9 Replies View RelatedSometimes corner snaps in sketch mode will turn off. why does this happen and how do I fix it?
View 1 Replies View RelatedI'd like to be able to vastly increase the size of the triad in the 3D Sketch environment - when sketching the triad is tiny and does not increase in size when zooming, this makes snapping to its planes extremely difficult.
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
How do I increase the size of the text of dimensions in sketch mode.
View 4 Replies View RelatedWouldn't be nice if you could use part parameters (description, part number, etc...) in the sketch mode text tool?
I'd like to emboss the actual part number on a part without having to retype the part number in manually.
I was giving a hand drawn wiring diagram (original.jpg) and it is a rats nest!!
I was asked to re-draw this and put it on our drawing template.
I have the plugs and terminal blocks drawn up and now I am about to attempt to add in the wires, but the sketch is so filled with dimension lines and values, it is going to be a task to try and make sure every line I draw is correct. This would be much easier to do if the dimensions could be turned off as the wires I am drawing will not be constrained.
I don't think there is layers options inside a sketch mode, or a if i start a new sketch I don't think I can project that sketch to the new one?
The only other options I can think of was to delete all dimensions and apply FIX constraint to everything! or
I guess I could have modeled the plugs and blocks in position and added them to the drawing, projected the geometry to a new sketch and added in my wires??
There must be someway to toggle the dimensions??
Inventor Professional 2014-Update 2 - AutoCAD Electrical 2014
Win7-x64 | ASUS P8Z77-V | i7 3770 -3.4 GHz | 32GB RAM |
240GB SSD | nVidia GTX 670 4GB - 320.49
I use 3D sketching frequently as a means to generate frames with the frame generator.
I notice that the constrain group no longer contains an equal length tool, as in a simple 2D sketch. This is where i would generally select two lines, and constrain them to be equal in length.
Is there a reason for this omission? Should I be worried that my menus are not showing the full options for constraints?
I opened Inventor 2013 this morning to find this issue. Everything starts fine, I am able to open/create a part file and enter sketch mode, but as soon as I click a draw operation (spline, line, rectangle, etc.) it freezes on me. I have been using 2013 for a couple months now without issue, and cannot associate this with a change of anything on my computer.I have tried:
1) Restarting computer
2) Reducing graphics display quality to Rough
3) Checking "Software Graphics"
4) Calibrate my 3Dconnexion mouse
5) The diagnostic check for graphics card (approved)
Cant figure this out - I create a sketch in a drawing, but I cant see the lines as I'm drawing them. The lines are on a "solid" layer set to red as defined in my standard. The background of my drawings is black. When the line command is done, the line appears and it's red. Problem is I cant see it as I'm sketching. Is there any way to modify this? Can I have the line appear red (or white) as I'm sketching?
Product Design Suite Ultimate 2014
Vault Professional 2014
Windows 7 Pro SP1
HP-Z400: 2.67 GHz 12 Gb Ram
Nvidia Quadro FX1800 driver 276.42
Just getting started, gone through all the tutorials back in 2008...
first time I've actually tried to make something,
Can't use the sketch b/c there's probably a gap in the outline, is there a quick fix?
(Did the entire thing in snap to grid, was hoping there's a function to either connect lines all at once, or ignore Extremely small gaps).
In sketch mode, there is a function to split lines, but I don't see one to join lines.
(I'm talking about colinear lines with the ends touching - I want to convert two lines into one).
It may seem trivial, but I'd like to use these lines in frame generator to select by a single line and not by endpoints of two different lines. Less clicks and more consistency in my model.
When I am in sketch mode I can draw a rectangle and when I go back to dimension it it only adjusts that specific line and not the connecting lines. Is there a setting or command to fix this?
View 1 Replies View RelatedHow can I have sketch lines drawn to perfect lengths. I mean it should be in multiples of 1/16 of an inch.
Inventor Professional 2013
Vault Collaboration 2013
I opened a part today and noticed that it had collapsed into itself.
This should be a rectangle 85x15.75:
On closer inspection it appears that the vertical lines somehow became zero length lines. Why does this happen?
Edit: I should mention that I was able to repair the skecth by making the 85" dimension driven, then dragging the line over...
I am having problems with lines disappearing in a sketch randomly. I am in a small assembly, going in and out of sketches used for machining, and then the sketch lines and dimensions will all be gone when I enter a sketch. If I hover over the sketch in the browser I can see the lines highlighted, but when I remove my mouse the will disappear. I cannot interact with the lines or dimensions at all. If I draw a new line, it immediately disappears. I have tried changing some things in the view tab and settings but haven't had any luck.
View 7 Replies View RelatedI have an oddly shaped flat plate extruded from a sketch, the sketch of which has lots on constructions lines, none of which actually represent solid edges of the plate. However, I want to locate the plate to other components via the geometry defined in the sketch.
I find that when I am trying to constrain the plate to other parts none of the sketch geometry is available to me. Points, lines, construction lines, circles; I can select none of it when constraining. I am confused. How can I constrain such a part?
Just to clarify - the flat plate is the base of a structure. Its profile is decoratively shaped, so nothing about the cut edge of the plate is suitable for constraining to. I need to constrain off geometry defined in the sketch.
I have "Shared" the sketch.
Inventor 2013
I have created a chassis wireframe using 2D and 3D sketches. In frame generator, I am able to insert frame members on the 2D lines, but not the 3D lines. I can put frame members on 3D lines ONLY if I use the "insert members between points" placement, but then I can't merge several members together to create 1 tube (can I?).
How do I put frame members on 3D sketch lines using the "insert members on edges" placement?
OR
How do I merge tube members when they are inserted using the "insert members between points" placement?
Inventor Professional 2013
Windows 7 64-bit
I have a question regarding copying geometry in drawing mode.
When I was working in V5 and making drawings I sometimes had to "fake" geometry, the world is not perfect I know, copy geometry in the 2d, like center lines and such. I am trying to do the same in Inventor and use the project geometry button and geometry is created but it does not show up when exiting sketch.