AutoCAD Inventor :: Drawing Built In Gears
May 23, 2013
Is there any way to draw built in gears by gear generator in Inventor? I mean, I need to create a spur gear around a solid body and then it is gonna be processed directly onto the body during manufacturing.
View 1 Replies
ADVERTISEMENT
Jan 18, 2012
I have two sets of identical spur gears. I want them to be lined and connected big-small-big-small gear. But how to connect this two sets together. I can create motion and axes constrains but it still lacks teath meshing. I found some tutorial how to create differential drive, it works with downloaded gears but not with one that I create (it says to set imates to visible which does nothing and alt-move mesh imates toghether which also do not work). I work with 2009 and 2011 versions.
View 1 Replies
View Related
Nov 5, 2012
How can I create bicycle gears that have different numbers of teeth but all have an inter tooth distance (distance between the teeth centres) of 12.7mm?
My attempt at a solution and problems encountered:
I made a bicycle gear by patterning a small circle around a large circle then trimming lines (see attached sketch), but this method requires me to estimate the diameter of the large circle before patterning and then keep modifying this slightly until I get an intertooth distance as close as possible to 12.7mm. So I can't get exactly 12.7mm. In my sketch I have labelled this intertooth distance I refer to by construction lines.
View 5 Replies
View Related
Nov 12, 2012
I'm trying to design a gear system wherein a small gear rotating on an axle interacts with a large gear, held on an arm. The arm rotates about the same axis as the small gear, in the opposite direction. I applied the relevant motion constraint between the two gears. When I rotate the arm, the motion of the large gear rotates the small gear. However, if I just rotate the small gear, it freewheels, and the large gear doesn't move at all. This is a problem, because the machine depends on the independent rotation of both gear and arm-- the small gear has an input applied to it, but if I try to rotate it it has no effect on the large gear. I assume this is to do with the fact that the large gear's axis of rotation moves with the rotation of the arm.
I can't just throw it all into dynamic simulation, because I don't know yet what kind of torques will be rotating the arm and the small gear-- I know how they rotate relative to each other in terms of degrees, but that's all.
Essentially what I need to do is make it so that rotating the small gear turns the big gear, even when the arm is free to move (when it's grounded, the gears turn normally). I thought about using a contact set, but the gears (generated by Inventor) actually slightly intersect at the teeth, so that doesn't work.
View 6 Replies
View Related
Mar 24, 2013
how we can design a set of internal gears?
View 1 Replies
View Related
Sep 28, 2012
I am trying to draw a bevel gears from drawings, one is a scroll plate and the others are gears with a key hole. As you can see in the following attachment.
My question is how do you draw bevel gears on the face of the scroll plate and the cylindrical face of the other 3 gears?
View 4 Replies
View Related
Mar 5, 2013
I'm given this data to generate my worm gear set with:
Worm Gear Data:
Diametral Pitch: 8
Number of Teeth: 27
Pressure Angle: 20 Degrees
Pitch Diameter: 4.219
Base Circle Diameter: 4.523
Circular Pitch: .491
Circular Thickness: .246
Root Diameter: 3.906
Face Width: .783
Worm Data:
Number of Threads: 5
Pressure Angle: 20 Degrees
Pitch Diameter: .938
Lead Right Hand: .375
Lead Angle: 169 Degrees
Addendum: .156
Whole Depth: .313
Chordal Thickness: .204
Inner Diameter: .619
Outer Diameter: 1.244
Center Distance: 5
My problem is it keeps changing data and/or failing. It particularly hates the 27 teeth (always changes it), never shows a 5.4 gear ratio (probably because it hates the 27 teeth), and won't accept an addendum of less than 1. Is this feature limited to only certain set gear setups? the automated tool won't accept these values (which I have to work with)?
View 2 Replies
View Related
Nov 8, 2013
I am having a problem while making 2 straight spur gears. The purpose is to connect the crankshaft with the camshaft. Center distance is fixed: 85,5mm. I would like a ratio of 0,5 with 22 and 44 teeth. My gears seem to hit each other. Please find the attached pictures below for a detail and my inputs.
View 3 Replies
View Related
Sep 20, 2011
I have two gears. In the assembly I have them setup to mesh correctly. I can drive the constraint on the pinion and the gear will follow it (some what). I wanted a better video of it, so I went into Studio. Now when I drive the constaint like before on the pinion, the gear goes crazy.
[URL]
There is a rotational translation constraint set between the pair (= to inverse of gear ratio) that works in the iam, but it is like Studion ignores it. How can I animate this to show the gear mesh?
View 1 Replies
View Related
Dec 10, 2013
Is it possible, using Design Accelerator to have Bevel Gears with straight teeth? I've tried every combo I can think of, and they are always curved teeth. Gears are not my most knowledgeable subject. I usually have the engineers produce the specs, & I get to draw them - they are not happy with the pictorial results.
Inventor Product Design Suite Premium 2013
View 4 Replies
View Related
Dec 21, 2013
I made internal gears with design accelerator.
It's calculation is OK. And drag it,the rotation is good, But the direction is opposite. The tooth's move opposite direction to each other.
I used Autodesk Inventor 2013, And sp2, update DL22436649.zip But, this appeard before And after sp2 patch.
View 3 Replies
View Related
Mar 30, 2012
I'm trying to draw a spiral bevel gears system KLINGELNBERG , but the results do not match the actual measurements of the piece.
ex. measure of the real outside diameter of the gear = 356mm
DATA :
number of teeth pinion = 9
number of teeth gear = 44
module = 5
shaft angle = 90 °
face width = 59mm
helix angle = 35 °
pressure angle = 20 °
View 2 Replies
View Related
Jan 28, 2013
I'm trying to run a simulation of 2 bevel gears without using the transitional/rotation constraint, but using the contact between the surfaces to simulate the rotation of the gears - basically I have an L-shaped shaft running through both centers and want to have the upper gear grounded, make the lateral gear rotate around its own axis - the goal is simply to see the contact between the gears make the side gear rotate around the vertical part of the l-shaped shaft, due to the contact forces.
View 2 Replies
View Related
Apr 4, 2012
When we generate a gear pair using the design accelerator, the balloon from the drawing assembly only reflect one number instead of 2 different numbers. How can we change the number to reflect individual gears. Attached is the graphics.
View 1 Replies
View Related
Nov 13, 2011
I am creating a couple of spur gears using the "Center Distance" design guide. I have fixed each gear to a cylindrical face, but when I click on the "Calculate" button, there is an error saying that the center distance is incorrect.
I went back and edited my sketches so the center distance matched the one displayed in the design accelerator and attempted to calculate again, but the error persists. What am I not getting here?
View 9 Replies
View Related
Dec 22, 2013
I'm trying to make some 3d spline gears in autocad, I start by generating them in eMachineshop then importing into autocad, this works fine but the gear is imported as seperat lines so I can't extrude them, i also cant join the lines because after zooming in there are quite a few gaps. How I can join the lines together without manually connecting the dots? I'll include a copy of the gear, eMachineshop only outputs dxf files as far as i know.
View 3 Replies
View Related
Oct 29, 2012
When trying to create a PDF file of any drawing with the inbuilt DWG to PDF AutoDesk plotter the software always crashes out with a FATL ERROR: Unhandled Access Violation Reading 0x0000 Exception at 21247a28h. Not sure if this is a coincidence but this has only just started happening since updating my Adobe Reader software to the very latest XI version just released.
I have sent several error reports to Autodesk but can't see any in the support section. I have tried un-installing the Acrobat Reader software and AutoCAD still crashes out. Creating PDF's from external printers like PDF24 have no issues but prefer the inbuilt printer as it keeps the vector data and layering info in the resultant PDF.
Using AutoCAD LT 2013 with service pack 1.1 installed.
View 9 Replies
View Related
Feb 7, 2013
We're using a precise level to as-built and create a dtm of a floor. The client would like us to assess the dtm for changes of grade greater than 3mm over 3m. (The test is based on walking around the floor with a 3m straight edge and 3mm blocks - see Figure 6 in this paper .)
Please note that the floor could be laid on a slope and still comply - it's the grade changes we're looking for. And some of these floors are large so we'd prefer make it as automatic as possible.
As far as I know there's no surface style that can display grade changes. We can shade each triangle by slope, but it will still require manual visual inspection to see if adjacent triangles are sufficiently similar to comply.
View 3 Replies
View Related
Jul 3, 2012
I left site, we are as building structures. When I id the current info, I have x and y co-ordinates but z values are 0, and when I try edit the z value it wont allow me to apply the new level .
View 8 Replies
View Related
Sep 11, 2013
how to create as built drawinngs in Civil 3d using surfaces
View 2 Replies
View Related
Aug 6, 2012
Wanted to know if there is a way to place pressure pipes at variable depths.
We got inspector notes which show the depths at each end of the pipes.
And I notice that under Pipe Properties, Part Properties tab, and under Geometry there is Start Cover and End Cover.
But both are greyed out.
Is it possible to use Star Cover and End Cover to design the pipes?
Using Infrastructure Design Suite Premium 2012
View 9 Replies
View Related
Apr 3, 2012
Having issues with data shortcutting custom built structure parts? I built a very simple part that has no dimensions and is for plan appearane only (it is a just a rip rap outfall). The part seems to work perfectly in my design file, appearing exactly as I desired with automatic labeling. However, when I data shortcut the pipe network into the plan presentation file, all default pipes and structures are brought in except for the custom built rip rap outfall.
I have tried to delete and reload the data shortcut, changed the part properties, and made sure the parts lists and styles are the same in both drawing files. If I swap the custom part out (in the design file) for a default part, the default part is suddenly displayed in my plan presentation file after synchronizing. It is as if the data shortcut doesn't recognize the custom part, even though it is in the network parts list?
Civil 3D 2010 & 2012
HP Z400 Workstation
Intel(R) Xeon(R) CPU W3550 @ 3.07 GHz
6GB of RAM
64-bit OS
NVIDIA Quadro 2000 running driver version 8.17.12.7105
Win 7 Professional
View 2 Replies
View Related
Oct 26, 2002
way to design a 2d gear in photoshop?
View 3 Replies
View Related
Dec 24, 2012
Having deleted the CS5 built-in actions, I tried to recover them by deactivating, uninstalling, deleting remaining folders/files, cleaning the registry, and reinstalling from scratch. But the built in actions did not install!
View 3 Replies
View Related
Jan 25, 2005
i have 2 layers: 1 is a picture and the other is the built-in "heart" shape. I would like to select the outline of the heart shape, crop it to make .... a heart shaped picture.
View 1 Replies
View Related
Feb 4, 2014
Are there any legal limitations on using the prebuilt animated backgrounds that are provided in AE CS6? Can we use them in commercial projects on the web? Can we use them for national broadcast?
View 3 Replies
View Related
Mar 18, 2008
I mean compared to a standalone panorama software? If not, which panorama software is the best?
View 1 Replies
View Related
Jan 24, 2012
I would like to try making a brass texture for a simple 3D build of a brass era antique car -brass lamp (in Second-Life)
I've done a Google search and have found several tutorials on making a " brushed metal surface" but nothing about brass itself. What color tools and values does one use to create a texture that looks like a nice warm, polished brass with typical brass highlights and shadows?
View 9 Replies
View Related
Jul 10, 2012
The subject says it.
I don't use any of the develop presets that ship with Lirhgtroom. How do I delete them? They are only cluttering my panel at this point as I have many of my own. Or, can I consolidate them into one folder? I can't seem to find where LR keeps them; they aren't with my preset folders. Nor are they in Win7>users>appdata>roaming>adobe>lr
View 11 Replies
View Related
May 16, 2012
Am using Photoshop CS5.1, Simply want to create a single picture (file) that has a "built-in" mat around it. Seems like all that's needed is a box in background (color it as a mat), then put the picture on top.
Problem is, when I go to size (or crop) the picture, it changes the size of the mat and Canvas Size. "Really" want the Canvas Size to STAY 16in x 20in, just makes it easier so can SEE and adjust (move, crop, slide arund) the picture to be 13in x 17in in the center or whereever. After all done, will save as jpg, so can view/print easily.
View 3 Replies
View Related
Dec 19, 2013
is it really necessary to convert other embedded color profiles to RGB built it? Gimp asks me from time to time if I want to convert Adobe RGB 1998 or Camera RGB Profile or CYMK to built in RGB. is this necessary to do or can I keep the profile? I usually convert...
View 1 Replies
View Related