See the attached image. I'd like to rotate the text of the dimension shown to be horizontal relative to the page.
The best I've found in searching for a solution is here (on the bottom):
[URL].....
however, following those instructions actually changes the dimension value to the distance projected in the plane of the sheet.
I was looking to change the fonts in a drawing for the Dimensions and Symbols that might have been inserted in the Dimension text entries.
This can be done manually bu editing the dimentions text after placemement, but I was ooking to set this as a default.. I cannot see where exactly this is controlled in the Styles Manager - I am only able to change the Dimension text font but the diameter symbol font is always on AIGDT.
I was therefore looking for an iLogicvb code that could do the trick, but I am not able to even change the dimension fonts... The code runs with no errors but nothing gets updated in the drawing...
Dim oDoc As DrawingDocument
oDoc = ThisApplication.ActiveDocument
Dim oSheet As Sheet
oSheet = oDoc.ActiveSheet
[Code]....
InventorVb.DocumentUpdate()
Can i change the length of the dimension line 'extension' when my dimension text placement is beside the dimension line (see attached image)?dim line length.jpg
View 6 Replies View Relatedevery one now a day i am making isometric drawings so i m little bit confuse in that i am using dimension and change the oblige angle text of dimension so is it right way or not ????
View 9 Replies View RelatedAll I want to do is rotate one dimension. I want to leave all the others alone.
When I am editing my drawing, I double click on the dimension and get the diag box and unfortunately the rotate dimension command along with the degree box is grayed out.
I have a plan with lots and lot numbering. I made the lot number text annotative and matching view orientation. But when it rotates in the view it rotates about the left justification point instead of middle as inserted into drawing. So I inserted lot numbert text into drawing and changed text to non-annotative, but now i can not change the text rotation angle unless i use rotate command on each individual piece of text (was trying to pick all text and change in properties box). Using feature lines to assist in grading design so not sure if this is an autocad problem or a civil 3d 2012 problem. I can rotate dtext made or inserted in drawing.
View 3 Replies View RelatedHow do I create an Inventor part with a cost that will update according to the part dimensions changing. For example, we design products using aluminum extrusions and our cost is determined by foot length. How can I create the extrusion part to have a per foot cost that will dynamically update when I change the parts length for an assembly? It seems to me to be a fundamental need for many industries.
I will happily take any links to information that will explain this process. I cannot find anything online that clearly explains the process of creating parts with costs and variables.
I have recently upgraded from LT06 to LT09.Why am I having trouble changing the text height on my dimension? I used to be able to double click on a specific dimension and change the text height to anything I wanted and than using the "match properties" icon change all the others.
View 9 Replies View RelatedWhenever I try to dimension a drawing in model space the text of the dimension comes out unreadably small.
I go into dimension style manager, I click on modify and I click on the text tab but the text height and fraction height scale is greyed out!
If I click on "new" dimension style the only option I get is to base it off my current dimension style with the text size greyed out again.
How to change the text size of dimensions if at the option is greyed out?
I am trying to dimension a drawing and have tried everything under the sun to change the text size but despite everything it keeps producing the text at a tiny size .
View 3 Replies View RelatedI am having problems with changing the height of the dimension text. I have tried going into the style editor and changing the text height in there and then saving it. The number for the height that I changed stays saved however the actual text height on the drawing does not, not even after I tell it to update.
View 3 Replies View RelatedI am in inventor and I need to draft up some diagrams for a lab report for school. They all have to be to scale so my dimensions will work properly, the only problem is, when I want to take a screenshot of the image to put into my document, the dimensions are way too **** small. I have tried everything to change them and nothing has worked. I don't know where my command line window is so I can't go directly to dimstyles.
View 3 Replies View RelatedWe need re-location the diameter dimension after we change the drawing view's scale. but we didn't know how to change the Startpoint of the dimension (mark with Red word "1"), just find the text location.
Who knows how to set the new point to for the startpoint?
I like to change the dimension of the length from 388mm to 400mm to represent another similar part with another part number. Yet I still need the old part.
What is the easiest way to do so? When I use 'save as" and then change the dimension, I need to recreate the dimensions in the dwg files. Is there a way to avoid creating the dimensions?
I'm chasing the syntax on what i hope is a very simple procedure.
We have a project for re-design and manufacture here (Australia) of a machine that has been designed and detailed in one of our US offices. For this reason, we will be wanting all dimensions in mm etc, rather than inch.
My intention is to open the idw(s), update the styles library (done, i think...), change the active standard to "AS Metric" (got the code sorted for that too), and then change all dimensions to AS Metric.
So far i have each of these 3 processes in a different sub, called from a master. But my problem is in changing the style. I could change a dimension's style to match that of another existing style:
Set oGeneralDimensions = oSheet.DrawingDimensions.GeneralDimensions.Item(1)
but I am having trouble setting is to the active style.
My module:
Sub ChangeStyle()
Dim oIDWDoc As DrawingDocument
Set oIDWDoc = ThisApplication.ActiveDocument
Dim oSheet As Sheet
Dim oDim As DrawingDimension
Dim oDimStyle As DrawingStandardStyle
Dim oGeneralDimensions As GeneralDimension
[Code]....
Is there a way to change the color of the dimension text?
I wanted to have the color of the dimension text different from the dimension line but couldn’t find where such option might be found.
I seem to recall being able to do this in 2013...
Say you've dimensioned something but end up wanting to change the dimension definition points...drag the end point to another location that you want dimensioned.
I thought it used to snap to a new location, but now it will not. I have to redraw the dimension (including all text I added).
Here is what I get when I try to move the dimension definition point:
Here is what I get when I try the auto-reattach feature in "repair". Still nothing to snap to.
I just started using Inventor and I have this issue, that whenever I set a dimension in a sketch, the sketch doesn't update to the new dimension until I move my mouse/cursor. Is this normal? Is there any way to change it so it updates as soon as I hit the enter button (after entering a dimension)
View 3 Replies View RelatedI need the dimension of .5 to become .25.It won't work, probably because it is the same dimension of Sheet metal Tickness.
View 3 Replies View RelatedHow do I change the dimension size in sketch mode?
View 4 Replies View RelatedMy piping route will not update when I change a dimension when editing the route itself. See below. I can change a dimension, the 3D sketch of the route will update, but the pipe will not move into the correct position. Doing multiple rebuilds and updates does not update the piping.
IV 2010 Tube & Pipe SP4; ACAD Mechanical 2010;
2.5 ghz Xeon Processor
8 gb RAM
Windows 7 Professional x64
EVGA GTX 560 2gb DDR5
I'm currently trying to dimension my working drawings, I was wondering how I could change the colour of the dimensions and dimension text so it stands out from the drawing.
View 5 Replies View RelatedHow do you add text before a dimension in the idw environment? For example, I have a dimension that shows 40".... I want to add text before it to say something like.... " 8 Spaces at 5" = 40" ".... The 40 would be the default dimension value, everything else I want to add to the dimension... I have added tons of text information behind default dimension values, this is the first time I need to add the text before the value and cannot figure out how to get it to work...
Example:
oLinDim(3).Text.FormattedText = "8" &" SPC'S AT" & vbCrLf & "5 = "
this adds text after the default value of 40...
I have a dimensioning problem. I have dimensions that I cannot modify as I normally do. I do not know what setting is stopping me but here is what it is doing. I add a dimension to a part. I then edit it to add 2X in front if it. It will then put it on top of the dimension. If I put it behind the text, it then goes beneath the dimension. There is no way to add text and it would actually appear on the same line as the dimension.
View 3 Replies View RelatedI have a user that wants to be able to either link dimensions to other dimensions, such as a ref dim to a live dimension or while inserting text in a note on the drawing to be able to list a dimension within that text string to a dimension of the part so as the part updates, the dimension in the text sting updates.
View 9 Replies View RelatedI am currently wanting to have my horizontal dimensions above the dim line and the postfix text below.
I can set this in inventor but when i do a save as autocad.dwg (2007) the postfix text either ends up above the line or puts a double space below the line.
Is there any way to change the size of dimension text in sketch? My students cannot see the dimension when I demonstrate the sketch.
View 9 Replies View RelatedI have been working on some spec sheets and, ideally, would like the text size larger to improve readability. When creating text, changing the size is as easy as editing the text and changing the size. With a dimension, however, that method doesn't work. Is there an easy way to change a dimension's text size without having to make a change in the styles??
View 2 Replies View RelatedI have a set of dimensions on my drawings however where the dimension is displaying as 6mm in a vertical plane this is quite difficult to distinguish as it could be misread as 9mm. Is there a way to add an underscore mark on the 6 so no mistake can be made as to it being a 6 and not a 9 ?
View 9 Replies View RelatedI have a problem with the display of the text string when creating a dimension, been through all the options within the styles manager however no option to display the text to the right of the dim line, it always defaults text to inside the dim line, where the option to toggle alignment of text on a vertical dimension line is ?
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
I'm aware this has been raised before, see [URL] however this was way back in 2004. Surely there must be a solution by now!
View 1 Replies View Related