I am having problems with changing the height of the dimension text. I have tried going into the style editor and changing the text height in there and then saving it. The number for the height that I changed stays saved however the actual text height on the drawing does not, not even after I tell it to update.
View 3 RepliesHow do i increase the dimension text height in my drawing.When i go thro the styles and standards editor and increase the text height all the text in my sheet border also increases.Surely there must be a way to isolate the dimension text from the sheet text.
View 2 Replies View RelatedI have been working on some spec sheets and, ideally, would like the text size larger to improve readability. When creating text, changing the size is as easy as editing the text and changing the size. With a dimension, however, that method doesn't work. Is there an easy way to change a dimension's text size without having to make a change in the styles??
View 2 Replies View RelatedI am having trouble changing the dimension text size of any 2d or 3d sketch..
the default has changed for some reason (i might have accidentally changed it while looking for something the other day) but i need to know how to change it back.. I can't do anything without a dimension getting in the way!
How do you change the dimension text size in an .idw 2D drawing? The dimension text and arrowhead size is too small and I would like to make it sligthly larger.
View 3 Replies View RelatedI have recently upgraded from LT06 to LT09.Why am I having trouble changing the text height on my dimension? I used to be able to double click on a specific dimension and change the text height to anything I wanted and than using the "match properties" icon change all the others.
View 9 Replies View RelatedI've just finished a large survey using GPS, this I've downloaded onto autocad. My issue is I've got loads of levels on cad drawing that I wish to make larger. These where downloaded automatically, onto drawing. Is there a way to change height of text, so all heights are larger, or do I hand change them one by one!
View 6 Replies View RelatedI have slope % angles labeled on a plan, but they are too large. They are 1/8" tall, and I need them to be 3/32" tall. I have checked the style (ROMANS) to be sure the text height is set to 0", and it is. I've also ensured that these labels are on this label style.
Check the screenshot. I added 2 screenshots with a huge difference in font size just to be sure my point gets across. And, I have hit APPLY and closed the window just to be sure. You will see up top, I have it set to 3/32". Actually the text isn't showing right, it is still stuck on 1/8". But, regardless, you can see in the lower screenshot where I have changed it to 3", but the text has not changed.
As a side note, the text on the slope labels should match the height of the contour labels you can see in the screenshots.
I need to change the width and height of some text i'm inputting to and image so that the height is 100% and the width is 75% in ariel size 11, how do i do it? I cannot find the answer on google,
also, the phrase capitalized, is this some special setting or does it just mean write in capitals
I want to change the text in my dimension. I don't actually want to change my the actual dimension, just the text. Is it possible? I want to create drawings that aren't to scale, and put in the dimensions that I want on there.
View 1 Replies View RelatedI want to override the measurement in a dimension with a string of text using a LISP command.
E.g.. "select dimension"
type new text for dimension
replace dimension measurement with new text. I can get the entity and its values, buy not sure which value to change for the "text override".
BTW Acad 2012.
When I export .idw in autocad .dwg, the tolerance text height of dimensions with 'Limits/Fits-Show tolerance' change, becoming the same of the dimensions text, while the tolerance text height of dimensions without 'Limits/Fits-Show tolerance' remain the same of the .idw file. Why? There's something I can do, to ensure that text height no change? See the attached pictures that show the problem.
I use Inventor 2011 with SP1.
I mean the dimensions in sketches in a model part, not the drawing dimensions which are controlled by styles .
View 1 Replies View RelatedWhen I add a text to a sketch, I can constrain the rectangle to set its size, orientation and position.And I can set the text width to fit into the rectangle. But I wasn't able to set the text height to fit into the rectangle.
Am I missing something or is the fit text option doing only half the job?
We are having issues with text height and variations depending on how the text is added.
I am currently adding etching to sheet metal parts by using the user parameters (which are driven by 3rd party source, excel file) and using a cut extrusion -1mm.
We have developed a marco which detects the shape of each letter and adds etching to our sheet metal program manually. We do this to get rid of the double lines when you cut text into a part. Our process is design in Inventor, unfold then convert to DXF 2004, where we import to our SM programming package (Radan).
I have noticed that when using 10mm simplex if the text is driven by parameters and 10 point text is selected the charecter height is 9.9928mm, however if the text is added manually it measures 10mm exactly. Why is this happening? It is probably of no concern to most, but we would need to add extra charecters to our macro to account for the descrepency, and in turn would take the macro longer to run.
When the text is added by user parameters, you can briefly see the 10mm text height flash to 9.99mm when finishing the edit sketch. Changing this to 10mm again has no effect.
what is causing this, or have any alternative ways of adding 10mm simplex single line etching to a dxf from an Inventor 2012 SM part?
Is it possible to change the text height of a drawing view label through VBA?
I have tried to change it by creating a new text style manually with the text height I require and then through VBA set the view label to use that style.
The View label takes on the new style but does not change the text height.
I have tried to use 'StyleOverride FontSize=' but I have text that is multi lined and using this command converts all my text onto one line.
Is it possible to change the text height of a drawing view label through VBA?
Below is my code so far,
Sub HoleDetailSheetLabels()
' Declare the Application object
Dim oApp As Inventor.Application
' Obtain the Inventor Application object.
' This assumes Inventor is already running.
'Set oApp = GetObject(, "Inventor.Application")
[code]...
If I click on any text the docker shows the incorrect height of the text. I have typed in an measured a 4" H and the docker display tell me its over 5.5".
View 13 Replies View RelatedHow do you add text before a dimension in the idw environment? For example, I have a dimension that shows 40".... I want to add text before it to say something like.... " 8 Spaces at 5" = 40" ".... The 40 would be the default dimension value, everything else I want to add to the dimension... I have added tons of text information behind default dimension values, this is the first time I need to add the text before the value and cannot figure out how to get it to work...
Example:
oLinDim(3).Text.FormattedText = "8" &" SPC'S AT" & vbCrLf & "5 = "
this adds text after the default value of 40...
(Again) The “leader” of the “dimension text” disappears when the text is moved! Why?
I’m wondering why the “leader” of the “dimension text” disappears when the text is moved.
How can I control this setting?
I need to show this “leader” all the time. Is that possible?
Please, have a look on the screenshots below (the file is attached).
I have a dimensioning problem. I have dimensions that I cannot modify as I normally do. I do not know what setting is stopping me but here is what it is doing. I add a dimension to a part. I then edit it to add 2X in front if it. It will then put it on top of the dimension. If I put it behind the text, it then goes beneath the dimension. There is no way to add text and it would actually appear on the same line as the dimension.
View 3 Replies View RelatedI have a user that wants to be able to either link dimensions to other dimensions, such as a ref dim to a live dimension or while inserting text in a note on the drawing to be able to list a dimension within that text string to a dimension of the part so as the part updates, the dimension in the text sting updates.
View 9 Replies View RelatedI am currently wanting to have my horizontal dimensions above the dim line and the postfix text below.
I can set this in inventor but when i do a save as autocad.dwg (2007) the postfix text either ends up above the line or puts a double space below the line.
My office has two desktop printers, both HP. Our Officejet 7000 wide format prints great. On the HP Officejet 7500, we are often seeing text printing errors. It will not print the text from vertical dimension strings, and cuts off some M-text at an imaginary vertical line in the middle of the text box. PDF's of the same drawing look fine. Is this a printer driver issue? Is there anything I can do within AutoCAD?
View 3 Replies View RelatedWe have detail drawings that contain horizontal and vertical dimensions. They're drawn at full scale in model space and saved as individual drawings. We then insert them as blocks onto a sheet in paper space, scaling them down to 1/2", 1/4" scale ETC.
Here's the problem - all the vertical dimension text appears bolder than everything else when scaled down. Horizontal text is just fine, diagonal text also looks a little bolder though.
When i mark Text/Dimension/Multileader and such in autocad 2011 LT, i get an issue, which i have tried to shown on the picture.The problem is that when i mark them, they show the current size they have, plus any other size they have had (Annotation it seems).
I Make a dimension. The overall annotation scale is 1:10. Now i change the overall annotation scale to 1:100. Then i set the overall annotation scale back to 1:10, i click my dimension, and it now shows how it currently looks, plus how it looked when the annotation scale was 1:100. This way i end up with every text object showing up 5 times when i mark them.
Home and work computers act differently when I initiate the dimension text edit command. One moves both the text and the dimension lines and the other only moves the text. It doesn't appear to be the dimstyle so I am wondering if it is a setvar.
View 2 Replies View RelatedIs there any way to change the size of dimension text in sketch? My students cannot see the dimension when I demonstrate the sketch.
View 9 Replies View RelatedSee the attached image. I'd like to rotate the text of the dimension shown to be horizontal relative to the page.
The best I've found in searching for a solution is here (on the bottom):
[URL].....
however, following those instructions actually changes the dimension value to the distance projected in the plane of the sheet.
I have a set of dimensions on my drawings however where the dimension is displaying as 6mm in a vertical plane this is quite difficult to distinguish as it could be misread as 9mm. Is there a way to add an underscore mark on the 6 so no mistake can be made as to it being a 6 and not a 9 ?
View 9 Replies View RelatedI have a problem with the display of the text string when creating a dimension, been through all the options within the styles manager however no option to display the text to the right of the dim line, it always defaults text to inside the dim line, where the option to toggle alignment of text on a vertical dimension line is ?
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
I'm aware this has been raised before, see [URL] however this was way back in 2004. Surely there must be a solution by now!
View 1 Replies View Related