AutoCAD Inventor :: Can Implement Magnetic Forces Into Model / Assembly
Jul 15, 2008Can I implement magnetic forces into a model or assembly?
View 9 Replies
ADVERTISEMENT
3ds Max :: Paint Object Tool Is Used To Implement Screws Into The Model
Aug 17, 2012im still trying to make a minigun following the tutorial but ive run into a problem, in the tutorial the "paint object" tool is used to implement screws into the model and make it more realistic. i have 3DS MAX 2010 and i believe that tool was introduced in 2011. what should i use instead? is there a plug in or something to get that tool in 2010? or is there some other way i should go about this?
remember im not continuing with my tutorial until i get past this speedbump
SKIP TO 15:10 TO SEE WHAT HE IS USING PAINT OBJECT FOR
THIS IS THE TUTORIAL: [URL]...
AutoCAD Inventor :: Assembly Model Brightness
Nov 15, 2013When i started my assembly, i could see all of my textures. Today, it is so bright that i cant even see any shadows. doesn't matter which view i have, i cannot see the texture. there is a glimpse of it when i look iso view but that is it. I have tried altering the styles to reduce the brightness down completely but it has no affect. if i open another assembly file and place the same part, i can see the texture perfectly.
How can i change it back so when i look from the front, i can see the wood grain laminate that i am supposed to see. i have attached 2 images. the white one is supposed to be a brown wood grain laminate that is shown in the other image. both images where using the same style with the same setting and are the same material.
AutoCAD Inventor :: G-Forces In Stress Analysis
Jan 6, 2014I am trying to properly stress test a steel aircraft fuselage. I can easily model the estimated weight of the pilot, copilot, etc as loads on the airframe. However, when it comes to simulating a high-G situation, (a load factor of around 7.5 times the force of gravity), I am not sure what to do. On one hand, I can simply multiply the loads on the airframe by the load factor and see if the frame can take it. In most cases, it performs very poorly, (safety factor less than 1). However, if I model all the loads under normal conditions, (normal pilot weight, etc.), then add a gravity load equal to 7.5 G, the airframe performs well. Yet I am not sure if the loads on the airframe, (such as pilot weight), are being adjusted along with the increased gravitational load.
My question is, what is the best way to accurately simulate real world loading for high-G situations?
AutoCAD Inventor :: Measuring Forces During Simulation
Jan 7, 2013If you can imagine a cylinder sliding on curve joint. Let’s say the curve is in the XY plane. In the output grapher it is possible to display the force as the cylinder slides around the curve. However if I understand it correctly the magnitude of the force will be in the direction perpendicular to the point of contact between the cylinder and the curve? In which case is it possible to actually find out the individual X and Y components of the force? That is to say the magnitude of the force in the X or Y plane of the curve?
View 1 Replies View RelatedAutoCAD Inventor :: Turning Assembly Model Into Shell?
Oct 5, 2012I would like to be able to the share external geometry of a fully assembled mechanical model without surrendering any part or assembly data. Is there a way to turn this assembly into an external surface "shell"…?
View 1 Replies View RelatedAutoCAD Inventor :: Get Printed Paper Model And To Assembly It
Apr 18, 2013I have to get the printed paper model, and to assembly it within Inventor.
At the moment, I have the chassis, and next step should be a surface modelling.
But I`m not sure, which tool should I use. Chassis consist of some bulkheads, and there should be one patch between two neighbors. Patches are already printed:
So I have to bend them, according to bulkheads profiles.
Question is: how can I perform this step? I can`t realize, how to bend these patches, to stich two neighbor profiles. Is it possible for Inventor? Or should I use the authomatic surface fill, and texturing later?
AutoCAD Inventor :: How To Show The Model Parameters Into Assembly Drawing
Nov 12, 2013I am working in one assembly. in that assembly i created all the part with using i part & same part i called in to the assembly & created i assembly. while creating drawing i have facing problem to show the model parameters in to the assembly drawing table. How to link the model parameters in assembly parameters with using i assembly.
View 1 Replies View RelatedAutoCAD Inventor :: ILogic Model - Dimensions Of Assembly In IDW Drawing
Jul 2, 2013I have a automated ilogic model that is then used within a 2D drawing, this 2D drawing then has dimensions on it referenced to the the model.
This model changes in its length the dimension associated with its length then changes but the dimension text then goes outside of the dimension boundary (does not stay central). Is there any code that can scan the dimensions and in effect tidy them up?
AutoCAD Inventor :: Black Assembly Model Appears In IPN File
Jul 20, 2012I'm working on an exploded presentation file and have finished all of the tweaks for each piece. One day, when I opened it up to do some work, there appeared a duplicate assembly model floating in the middle of my work space. The duplicate does not appear in the model browser and is completely Black. It dissapeared a few days later, but the next day, when I opened the file, it was there again.
View 9 Replies View RelatedAutoCAD Inventor :: Extract Rev Of A Model (part Or Assembly) From Drawing
Dec 7, 2012I'm trying to extract the Rev of a model (part or assembly) from a drawing. Since Inventor has independent revs for the model and idw I am trying to drill down and put the rev from the model referenced. I got it to work for ipts and many iams using:
Dim oModelDoc As Document
Set oModelDoc = oDocument.Sheets(1).DrawingViews(1).ReferencedDocumentDescriptor.ReferencedDocument
The problem I have is when the drawing only references an ipn presentation file. The ipn ALSO has it's own independant rev! I'm trying access the model the ipn references but cannot get it to work.
BTW, I do know about the ability to sync idw and ipt properties. I have enable it for our template but we have a lot of legacy drawings that don't have this option selected. I also haven't tested that method with an drawing that only references an ipn.
Code is below with offending section in bold:
' Find model (part or assembly) referenced by drawing if active document is a drawing
If oDocument.DocumentType = kDrawingDocumentObject Then
Dim oModelDoc As Document
Set oModelDoc = oDocument.Sheets(1).DrawingViews(1).ReferencedDocumentDescriptor.ReferencedDocument
[Code]....
AutoCAD Inventor :: How To Open Model Or Assembly On Lower Version
Apr 11, 2011I have one problem presentaly i am using Autodesk Inventor Pro 2011, if i have to open a model which is created in Autodesk Inventor Pro 2012.
Autodesk Inventor Professional 2012
AutoCAD Mechanical 2012
Windows 7 64bit, Office 2007 Pro
Intel(R) XEON(R) CPU @2.40GHz 2.53GHz, 4.00 Gb RAM
NVIDIA Quadro 600 Graphics
465GB SATA TOTAL, 124GB SATA working folder
AutoCAD Inventor :: Implement New Style Library For Dimension Styles
Oct 15, 2012I am trying to implement our new Styles Library for our Dimension styles. I keep getting this error (see attached).
I have done everything I can think of, I have mapped the default library to the new styles library location on the server. I have tried everything.
AutoCAD Inventor :: Reaction Forces From Static Stress Analysis (2014)
Oct 1, 2013I am using Inventor 2014 to do a simple stress analysis.
I am looking for the reaction forces at fixed boundaries, but I can't find how I can get them. Displacement, stresses, strains, everything works, but where are reaction forces?
AutoCAD Inventor :: Custom IProperties Not Updating In Drawing When Update Assembly Model?
Nov 19, 2012I'm using Inventor 2011 and when I go to change parameters using iLogic in an assembly model, (sometimes it is a component suppression, other times it is an iPart component change) it won't update the associated drawing file. I need to go into the BOM on the drawing and renumber the balloons, or change something else in order for the custom iProperties to update in the drawing template. If I just change the iPart component, then the BOM doesn't need to update making the renumbering of balloons redundant.
I'm using iLogic to update all of the iProperties and component references, then reattach balloons. What I would like to do is automatically update the custom iProperties drawing template fields, and renumber the drawing BOM.
AutoCAD Inventor :: Create A Treeview Of Model Tree Which Displays Parts Assembly
May 15, 2013I am trying to create a Treeview of Model tree which displays parts assembly...etc My code is working well and i am able to get the tree view, but the problem is how can i count the quantity of parts/assemblies and display as consolidated. For instance this below snapshot shows my treeview.
This above snapshot shows my output
Here besides all parts/assemblies i get Semi-Colons and Numbers rather than consolidated view For this part in fig
153049 QSL.1_8.8:1
153049 QSL.1_8.8:3
153049 QSL.1_8.8:3
153049 QSL.1_8.8
and Quantity as 3 separately.
AutoCAD Inventor :: Simulating Magnets And Magnetic Moment?
Jun 28, 2012I am working on a project for an electricity and magnetism class that deals with using neodymium magnets to propel other neodymium in around a ring. Any method of both importing neodymium or any other rare earth magnetic material into Autodesk Inventor 2013 and then running a dynamic simulation on an assembly consisting of those parts.
View 4 Replies View RelatedAutoCad :: DWG Forces To Partial Open Always?
Sep 28, 2011I'm trying to run my cleanup script on a set of drawings just received from a consultant. Unfortunately every time a DWG is opened the purge fails with:
PURGE cannot be used on partially opened drawings.
Now to get the file opened NON-partially, I have to first open as partial and click the "Load All" button and "Yes" to bloodywell open it normally. Then the purge actually "works".
This needs to be done manually. Yet even after I've done this and then saved the DWG again, another normal open again gives the same error about Purge not allowed.
how to get the DWG to open non-partially when I'm running my SCR? I don't want to clean the 80+ drawings manually.
AutoCad :: Calculate Forces The Object Can Withstand
Aug 7, 2012I am designing wing ribs for a prototype, ribs made with fir wood; I must make cuts in the ribs in the form of circles or triangles to reduce the weight but keep the strength. I think I will use circles because a triangle's corners can be starting points for fissures(maybe triangles with rounded corners?).
Given: wood type,fiber alignment, rib dimensions, pattern of circles and circles' diameters, can Autocad calculate the forces that rib can withstand on each axis ox,oy,oz?
Is there another program that can tell me what forces an object can withstand given information about that object?
AutoCAD Inventor :: Convert Weldment Assembly Back To Regular Assembly Template
Jun 6, 2012I am using INV 2012 and I wan to to know a trick how to convert the weldment assembly back to regular assembly template.
View 1 Replies View RelatedAutoCAD Inventor :: Creating Separate Assembly Out Of Various Component Parts In Existing Assembly
Jul 10, 2012I'm looking for the best way to create a separate assembly out of various component parts in an existing assembly so that the whole thing can be placed in an assembly as you would a part, I know it's possible to demote components within an assembly but are there any other methods similar / better ?
View 2 Replies View RelatedAutoCAD Inventor :: ILogic Assembly Has Double User Request At Inserting In Assembly
Sep 18, 2012We have an iLogic assembly with to parts in it. Maybe to cylindrical parts. The iLogic rules should do the following.
1. Start a Rule after open document.
2. This Rule starts a Rule in the first cylindrical component.
3. This Rule ask the user for a diameter.
4. The assembly gives this new parameter value to the second component
5. Then the assembly calls another rule in the second component to change it with the new parameter
Everything is working fine when the following combinations are taking place:
1. I open up the assembly out of vault or from a local drive or an accessible server drive
2. I insert the assembly as sub assembly in another assembly from a local drive or an accessible server drive
It don't work with the following situation:
- I insert the assembly as sub assembly in another assembly out of vault
Then the user becomes the dialog "Choose a diameter" twice.
I don't know why, but I have the idea it has something to do with the functionality of inventor to insert a component more than once. If you insert a component in an assembly Inventor gives you the opportunity to add more than one occurence after each other.
change that behaviour? Maybe a switch to change that inventor "add more than one occurence" behaviour.
AutoCAD Inventor :: Tube And Pipe Assembly Styles Don't Translate Into Other Assembly Files
Feb 9, 2012I have encountered a problem with the Tube and Pipe styles.
As you can see, I have a rack assembly with a custom tube and pipe style. A wire as a tube in orange, and a tube support in white. Both have their seperate colorations at a style in the tube and pipe styles editor
When placing the rack assembly into the main assembly, it reverts to the coppor coloration I changed from the original style.
Steps I've taken:
Exported the styles .xml and Imported the styles into the master tubeandpipe.iam
Imported the user created .xml styles into the main assembly file nothing seems to work
AutoCAD Inventor :: Find Interior Volume Of Assembly By Subtracting Assembly From Block
Apr 23, 2012I am trying to find the interior volume of an assembly (when am I not?!?!) by subtracting the assembly from a block that surrounds the most of it. Somewhere the assembly has a "leak" and I have been trying to use the Cross Section Analysis to track down where the inside lump is connected to the outside lump to be subtracted. Is there a less time consuming way to dynamically drag a plane across and get cross sectional views?
Even better is there a simple way to animate the analysis plane moving across the block so I can hopefully just watch and pause it when I find a leak?
Inventor 2013 (SP2 Update 2), Windows 7 Professional (64-bit), SP1, Intel Xeon 3.07GHz CPU, 12GB RAM, NVIDIA Quadro 2000, Vault Basic 2013
AutoCAD Inventor :: Place Assembly Constraints With Parameters From Parts In Assembly?
Oct 30, 2012it is possible to make a constraint that utilized a parameter of a part within the assembly.
For example, if I wanted to use the thickness of a plate, which I defined in the part, could I call that parameter in a constraint?
AutoCAD Inventor :: Make Sub Assembly From Parts From Main Larger Assembly?
Oct 31, 2011My assembly has grown (about 50 parts) to where I need to consolodate some parts into subassemblies for reuse and alternate iterations of the basic design.
When I import the original parts into a new assembly, all of the constrains I created are not there of course.
I've tried creating a new empty part and then deriving a new part from the assembly, but I can't add, delete or edit any parts.
I looked at using Shrinkwrap, Substitutes, iParts, Multi-body Parts, and Multiple Solids but I remain confused.
In retrospect, maybe I should have created the subassemblies between the part and assembly stage but I didn't.
AutoCAD Inventor :: Translate Assembly Component Using ILogic / Offset From Parent Assembly Origin
Nov 9, 2011I want to be able to control the location/position of a component in an assembly. This is easy enough through the iProperties/Occurrence tab and then adjust the location of the X,Y, and Z offsets. Is this possible using iLogic? I have been unable to find a function to access via iLogic. Ultimately I am trying to translate a component about an axis not a pattern.
View 1 Replies View RelatedAutoCAD Civil 3D :: Make Label In Model Space For Assembly Name?
Jul 20, 2010Is there a way to make a label in model space for an assembly's name? To keep track of which assembly is which, I have been creating a MTEXT object and just type it in below my assembly. I would like to know if there's a way to make a label just show up with the name so I don't have to create all these text items manually. This would be just for reference only, not used for any final plans.
Infrastructure Design Suite Premium 2014
Civil 3D 2014 x64
Windows 7 64-bit
6GB RAM
AutoCAD Civil 3D :: Implement Railway With Double Track?
Jan 6, 2013I used a little bit Civil 3D 2013 for railway design purpose. I understood all the basics but I still have a question : how to implement a railway with double track? In the library, there is only SingleRail subassembly. I'm not sure how to implement what I want or if it already exists in Civil 3D 2013. I found a topic (2006) : [URL]
View 2 Replies View RelatedAutoCAD .NET :: How To Implement Drop-down List (based On IDynamicEnumProperty) In OPM
May 25, 2013Is there somone who can explain/show a sample of how a custom drop-down list in OPM can be implemented? Based on some articels by Kean Walmsley, I have successfully implemented categorized properties in the OPM using a .NET wrapper and C#. I have a class imlementing the members of the IDynamic EnumProperty, ICategorizeProperties and IDynamicProperty2 interfaces (based on ObjectARX 2013).
However, I do not really understand how to code custom drop-down list using .NET wrapper and OPM. I am using AutoCAD 2013 and 2014. I have read a lot of posts regarding OPM but there was no useful information in regards to create custom drop-down lists.
AutoCad :: Implement Numbering System In Product Design
Mar 26, 2012Any good numbering systems that they currently implement in product design, rather than the conventional architectural numbering system mostly seen on websites and forums.
View 3 Replies View Related
