AutoCAD Civil 3D :: Trimble Export Road Files Corrupted?
Apr 4, 2013
Trimble Access, Civil 3d 2012 export road problem
when I export a road file to my TS2 it becomes corrupted (file size 50% of what it should be.
4 months ago there was no problem. The weird thing a is that the other worstation in the office has this issue to.
Here's what I have done to troubleshoot: swapped out both data collectorsexported this rxl file to a virtual instrument on my desktoptalked to cansel and autodesk but the said they haven't seen this problem. I can rule out the following.
trimble/autodesk software, hardware ( to much a coincidence that both work stations have this problem)Data Collectors swapped out - file size of the corrupted rxl were the same on the virtual deskto instrumentcorrupted dwg - exported a road six months ago, now re-exported and the new file is corrupted.
Both machines are identical:
Pentium Zeon
16 gb RAM
Identical software installation
View 3 Replies
ADVERTISEMENT
Oct 30, 2013
When exporting points to a .TXT using PNEZD the elevation goes haywire.
After being exported it reads roughly 69000 in an area where the elevation should be about 5400 to 5800 feet
(very roughtly a factor of 12)
Is there a variable I can change to fix this?
View 6 Replies
View Related
Sep 11, 2012
I'm trying to import a .job file from our Trimble R6 GPS with Trimble Access software. I save the drawing and select import job. I have a device setup so I can navigate to the .job file, so i select the .job file and it starts to convert it, then i get the following error:
"
Unable to convert file.
Database Open Failed
File: [filepathhere] estjob.job.tic <--- not sure why it says .job.tic here its just a .job file
Select Abort to cancel the current operation
Retry to try again with this file
Ignore to skip this file and try the next.
"
If i hit retry it just keeps giving the same error, if i hit abort or ignore I get the following error:
"An error occurred during the file download. A required geoid model, datum grid or project grid file may not be available on this computer, or, This computer may need the "Update Office Software" option (from the Trimble Survey Controller CD) applied to it."
I've tried with Civil3D 2011 and 2012 both with Trimble Link installed for their respective versions. I have Trimble Business Center installed and updated along with Office Synchronizer. I went to Trimbles site and downloaded and installed all the update office software utilities in order in which they were released, the latest being April 2012. I tried uninstalling Trimble Link and reinstalling. I also downloaded and installed Trimble Office Configureation File Update Utility which last updated in August of 2012 and was suppose to update Trimble Link. I tried making a couple of test jobs on the data collector, some in state plane coordinates and some with no projection/no datum so a geoid file wouldnt be required, but they all return the same results. I've installed the geoid files on the collector using Trimble Link's Install Geoid and also added them to the Coordinate System Manager in Trimble Business Center.
I would like to convert using this utility because it gives azimuths and distances from our base receiver and I can use them to do adjustments after the job file has been converted to a fbk (fieldbook file).
View 5 Replies
View Related
Apr 13, 2012
I am trying to utilize Trimble's ability to export Points to an XML file. The XML file contains some additional Attribute data. I have created the new Point UDP's and also Created a new Point File Format. Here lies the Problem, when I go to the Insert Tab in the Ribbon and pick import from XML. It gives me no choices to select a Point File Format? It just imports the file with just PNEZD data only, and not my additional Attributes.
View 7 Replies
View Related
Feb 18, 2013
I am looking for something to convert .job files to .fbk files. I have Trimble business center and AutoCAD C3D 2013.
I haven’t got them to work together yet. I am trying to upgrade from Trimble geo office, which makes perfect field book files but it won’t work on my new computer.
Trimble says TGO is obsolete and that it just doesn’t work on new computers but I can't see why not..
View 2 Replies
View Related
Aug 21, 2013
I need to model road with same elevation. But also need to model ditch along road which has a slope of 0.2%. how can i make a ditch with slope.
View 2 Replies
View Related
Jun 7, 2012
Tune up utilities got into my system and was finally removed by windows installer today. I tried 2 times to repair Autocad2011 civil 3d, then 3 times to reinstall it, finally removed all files I could find and tried 2 times to install. Cannot install I get eror 1402 about the key being too full or somtehing like that. It is the student version but I use it for my own use and need to access the files.
View 3 Replies
View Related
Aug 8, 2013
We're moving to Trimble Access on the survey data collectors which means that we have to export design data using Trimble Link and then use Trimble Business Center to examine the data and do any editing before sending it to the field.
So far I've found that alignments, profiles and surfaces seem to transfer OK. Corridors however have been an almost total failure.
Civil 3D 2012 & 2013 & 2014
Toshiba Qosmio X505-Q890
2 x i7 - Q740 quad core CPU's
8GB of RAM
60GB SSD + 500GB HDD
NVidia GeForce GTS 360M - driver 8.17.13.0697
Win 7 Home Premium
View 2 Replies
View Related
Jan 27, 2010
I have installed Trimble Link for Civil3D 2010 and the menu will not appear in Civil3D anywhere.I re-installed it 2 times, which sucessfully completes, but to no avail.I checked cui and it's not there to add either.
View 4 Replies
View Related
Oct 23, 2013
I am using Civil 3D 2014. When click any of the buttons in the Trimble Link Ribbon, I get the following message:
TRMBIMPORTDATA Unknown command "TRMBIMPORTDATA (Or whatever command that had been issued)". Press F1 for help.
Another user in our office has everything in the Trimble Link work fine. We have tried upping my status to administrator for my computer, and that didn't work. When I installed CIvil 3D, I checked every button to be installed in the infrastructure design suite package....
View 7 Replies
View Related
Mar 14, 2012
My surveyor gave me a Trimble .tsf point cloud file....how do I convert that dude to an AutoCAD .las file?
View 2 Replies
View Related
Mar 12, 2013
We often have to create dxf files for surveyors to use in Trimble survey controllers. Usually, the linework has to be 3D polylines so that they can stake out the lines on the ground in 3D.
When compiling our design we often have to use arcs which do not function as 3D polylines. To get around this, we convert them to feature lines. This works for creating surfaces but we are unable to export these feature lines in our dxf files.
C3D 2012
Win 7 64 i5
8GB RAM Quadro FX 1800
View 4 Replies
View Related
Jun 29, 2012
When I export a drawing into pdf, the yellow color of the paint on the road changes to black. The export had worked fine until I c/p an image under my line-work.
View 3 Replies
View Related
Mar 6, 2012
Since the last update I am having images corrupted (truncated) by lightroom, when I open some files in CS5 i get the message about the file being truncated and then only half the image come up.
If I export the file again from LR it works so it's not the usual card malfunction or import errors, my hard drive is in fully working order and tested with drive sentinal.
View 3 Replies
View Related
Jan 30, 2013
running an assembly in to the road corridor and creating a surface. i have designed a network of Roads in CIVIL 3d in which whole network is surrounded by a Loop road. The loop road cross fall is unidirectional (2%) and 4.5 wide. I have used LaneOutsideSuperWithWidening subassembly to create the assembly of the road. This doesnt contain any kerb or footpath but only road channel lines, The corridor run soomthly but after creating the of the loop road corridor the surface is becoming flat meaning there isn't any cross fall acoss the road but in the assembly crossfall is there. If i run the same assembly in another road alignment the suface is coming absolutely correct.
I also tried different road assemblies to run along the loop road but the result is same no cross fall across the road.
View 2 Replies
View Related
Feb 1, 2012
I am working on Street Improvement Plan using Civil 3D 2012. I have my centerline stationing set for major (100') and minor (50'). My street plan is kind of busy with a several call-out/label, leader etc. I want to set my my station for both major and minor with with decimal to read as 1+00 or 1+ 50 as opposed to 1+00.00... How to get rid of the decimal points.
View 6 Replies
View Related
Nov 4, 2013
Road design civil 3d complete files (Plan, Profile with complete band, Assembly , corridor, sections etc .
View 5 Replies
View Related
Nov 19, 2012
I have make a road network. Then i make a corridor surface using corridor extends as outside boundary. I also create a boundary in the interior side of the roads with interactively tool, and i use it as a hide boundary. The corridor surface look fine but when i am trying to make a finish Ground Surface pasting the corridor surface after Existing Ground surface then the hide boundary of corridor surface make holes in finish Ground surface.
View 3 Replies
View Related
May 30, 2013
Is this a desired behavior on a multileader? URL....
Seems to do it for anything that is not left aligned. I think it was present in 2013 as well. I use multileaders for annotations a lot since it is easier to use them with the background masks and borders than mtexts.
View 5 Replies
View Related
Dec 10, 2013
I am creating P&P sheets for my road. I created view frames, and when I got to create sheets, I pick "all layouts in new drawing". I go to open the new drawing up, but all that shows up/tranfers is the profile and alignment, nothing else comes over ( proposed linework, existing linework, etc.)??????
View 4 Replies
View Related
Nov 5, 2011
Why oh why when I export any image from one folder to another do I end up with most keywords applied to that image written to my hierarchical keyword list as a new 1st level keyword and not under the parent keyword as they should be? I've tried everything. I'm using Windows 7 64 bit, with the latest LR 3. Export Synonyms, Include on Export, Export containing keywords are all checked with all the keywords and I've unchecked the Write Keywords as Hierarchy in the Export dialogue. With every export I have to clean up my keyword list and I'm at wits end with wasted hours.
View 7 Replies
View Related
Oct 1, 2012
having major issues with sheet sets in Autocad 2013 (actually we're using Autocad MEP 2013... but haven't gotten any responses to my post over in that forum so trying it here too). We use them constantly, and up til now they've worked great. In 2013, we can't get a .dst file to stay valid for more than 2 hours. You can create them & work with them just fine, but once you close & reopen AMEP it says the .dst is invalid, and it creates a new .dst of the same name in the same directory w/ 0kb file size. After that, nothing works... view names, sheet titles, etc., everything that is driven off the sheet set. And of course every time you have to recreate a sheet set, you have to recreate every detail callout, sheet title, detail title, etc. in the set of drawings.
We've installed AMEP 2013 SP1, doesn't make a difference.
All of our machines are Win7 Pro, mixed 32- & 64-bit, with plenty of processor/memory/graphics capability. Our standardization stuff runs off of our network/NAS drive.
View 9 Replies
View Related
Feb 27, 2013
I am new to Civil 3D and need to customise the look of road profiles so they look like they were produced from any of our other civil design software packages that we use (to maintain standards between offices etc).
The attached picture is what I need them to look like. I want to show both the natural ground (the dotted line) and the design road line (solid). Then I want to write on the profile the station, natural level and the design level.
I've got the Mastering Civil 3D book (and a few others) sitting on my desk.I worked out how to turn off the grid on the default profile althoguh that was about it.
View 1 Replies
View Related
Apr 24, 2013
is it possible to break surface in SAC road way mode?
View 6 Replies
View Related
Apr 30, 2011
I have cross section data of the existing ground in the form of offset elevation. Can i draw cross sections from the this data? I am using Autocad Civil 3D.
Formate of the data for one section is:
Station 12+000
offset Elevation
-25 350
-20 347
-15 348
-10 346
[code]....
View 9 Replies
View Related
Dec 2, 2013
I am preparing to model a road surface for a waterline project. I would like to be able to generate sections at desired stations showing the sewer, storm drains and joint utility trench along with the proposed water line. My plan is to model the road surface using a surface created from gradings and then create the pipe networks and joint trench.
My question is whether gradings or corridors would be the way to proceed. I have preliminary design data on the road surface which is sure to change.
View 4 Replies
View Related
Jul 10, 2013
i have been working on a DWG (c3d 2012) most of the day, and sure enough, after my last edit in Model space, c3d crashed.
i can remain in model space, but once I try on open the only layout tab, c3d hangs and crashes. i was able to create a new layout in the command line and rebuild my layout, but i still cannot open the original tab without a crash. i ran AUDIT and found 2 errors, but if i allow c3d to fix or delete them, c3d crashes. also, if i run PURGE, c3d crashes.
how i can determine what is at fault or a method to maybe even isolate the problem? maybe a trick?
View 1 Replies
View Related
Nov 20, 2013
When i create an intersection, I get error - " One or more of the secondary road profiles cannot be locked at this intersection . What do you want to do ". Both of alignments and profiles is a reference from a data shortcut .
View 1 Replies
View Related
Aug 14, 2012
We have lucky enough to obtain LIDAR for most of our small City as well as ground only points. My problem is that profiles produced using it are rough and jagged (see attached). I've tried contour smoothing to no avail as well as point removal. Perhaps I haven't just tried enough options.
Should mention also I have breaklines along the CL alignment as well as Edge of Pavement.
View 6 Replies
View Related
Apr 9, 2010
how to create a label style for design center of road (simple tangent) in profile that will work between multiple profile views. I've used the 'Create Multiple Views' profile view wizard. I use a horizontal dimension style label for CL road (looks just like an autocad linear dimension). I'd like the label work across separate views i.e. stop at view end, pick back up at view start.
The label I currently use is simply a line component from tangent start dimension to tangent end dimension and the text component is anchored to the line midpoint. Label looks as intended for normal use. For some reason the line drops as if looking for the actual pvi at the right side when i use multiple views.
View 3 Replies
View Related
Jul 9, 2013
I went forward designing intersection profiles with limited survey and simply made an educated guess for the secondary roads pgl tie in point. I have received updated survey and when I move the profile end point to meet existing grade it adds another pvi effectively holding the profile grade I set preliminarily. I'm keeping the lock point. Is there something with the return/ offset profiles preventing this edit? What is the proper work flow?
Civil 3D 2012 & 2013
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram
64 Bit Win7 OS
View 3 Replies
View Related
