AutoCAD Civil 3D :: Corrupted Layout Tab DWG?
Jul 10, 2013
i have been working on a DWG (c3d 2012) most of the day, and sure enough, after my last edit in Model space, c3d crashed.
i can remain in model space, but once I try on open the only layout tab, c3d hangs and crashes. i was able to create a new layout in the command line and rebuild my layout, but i still cannot open the original tab without a crash. i ran AUDIT and found 2 errors, but if i allow c3d to fix or delete them, c3d crashes. also, if i run PURGE, c3d crashes.
how i can determine what is at fault or a method to maybe even isolate the problem? maybe a trick?
View 1 Replies
ADVERTISEMENT
Feb 27, 2013
I have a bit of a problem with Autocad map 3d 2012. When i try to insert a scale bar or a north arrow or any other carthographic element i simply can't find the layout elements that are supposed to be in layout tools tab. I've done a lot of research online and can't come up with anything.
View 2 Replies
View Related
Oct 30, 2013
When exporting points to a .TXT using PNEZD the elevation goes haywire.
After being exported it reads roughly 69000 in an area where the elevation should be about 5400 to 5800 feet
(very roughtly a factor of 12)
Is there a variable I can change to fix this?
View 6 Replies
View Related
Apr 4, 2013
Trimble Access, Civil 3d 2012 export road problem
when I export a road file to my TS2 it becomes corrupted (file size 50% of what it should be.
4 months ago there was no problem. The weird thing a is that the other worstation in the office has this issue to.
Here's what I have done to troubleshoot: swapped out both data collectorsexported this rxl file to a virtual instrument on my desktoptalked to cansel and autodesk but the said they haven't seen this problem. I can rule out the following.
trimble/autodesk software, hardware ( to much a coincidence that both work stations have this problem)Data Collectors swapped out - file size of the corrupted rxl were the same on the virtual deskto instrumentcorrupted dwg - exported a road six months ago, now re-exported and the new file is corrupted.
Both machines are identical:
Pentium Zeon
16 gb RAM
Identical software installation
View 3 Replies
View Related
Apr 13, 2012
Ever since I got back to my desk after theEaster break I have had an odd problem witj C3d 2012.
The pop up names of the buttons along the bottom (snap, grid, osnap etc) are apparently now in Chinese. Tool tips for other tools are also containing a mixture f what appears to be Chines plus corrupted characters.
View 2 Replies
View Related
Jul 10, 2012
I was undertaking a cut and fill analysis but the values were very different. Evaluating spot levels the depth was given as 1.2m but the volume surface stated it was only .6m.
After a while I noticed that the master surface had been "corrupted" duing a recovery, all definitions to the controlling corridor and other objects had been removed and a snapshot added with the description "added during recovery".
I had to remove the surface and start from scratch re-building the definitions.
Civil3D 2013 / 2014
Windows 7 Professional 64-bit
Intel(R) Core(TM) i7-3820 CPU @ 3.60GHz (8 CPUs), ~4.0GHz With 32768MB RAM, AMD FirePro V4900, Dedicated Memory: 984 MB, Shared Memory: 814 MB
View 3 Replies
View Related
Jun 7, 2012
Tune up utilities got into my system and was finally removed by windows installer today. I tried 2 times to repair Autocad2011 civil 3d, then 3 times to reinstall it, finally removed all files I could find and tried 2 times to install. Cannot install I get eror 1402 about the key being too full or somtehing like that. It is the student version but I use it for my own use and need to access the files.
View 3 Replies
View Related
Apr 27, 2010
Just upgraded from Civil 3D 2010 32-bit to Civil 3D 2011 64-bit. Over the years several user-defined color books were constructed using the Autocad Color Book Editor. With previous upgrades, these ACB files were simply transferred to the new version and worked OK. However, having upgraded to 2011, when the color books are opened, instead of the original colors, the color pages are corrupted, showing what look like Pantone red, green, and blue colors.
View 6 Replies
View Related
May 20, 2013
When I switch to a layout there is a panel "Layout Tools" that grabs focuse. I've never had it before, where/how I turn it off?
View 6 Replies
View Related
Nov 13, 2013
Where should i insert my point tables? In the model or the paper space?
in the paper space it seems that i cannot control the insertion scale?? i set specific letter height that works fine at the model but in paper every time i create a table I see different size depending on the zoom I have.
View 1 Replies
View Related
Sep 2, 2010
I am trying to layout a road profile. I have created a profile view with my existing surface. I select "Create Profile View By Layout" in the pulldown to create my vertical road geometry and I get the Profile Layout Tools pop-up but all the buttons are greyed out so I can't do anything with it. I am using C3D 2008.
View 3 Replies
View Related
Feb 28, 2013
For some reason our layout tabs keep re-arranging themselves. All of a sudden our sheet 2 ( or what ever) is between tabs for sheets 35 & 36 (or where ever it wants to be).
we use tabs because 45 sheets of images require never ending scrolling. the current tab is never the image shown....they always start at the 1st tab?
when you are on sheet 40 and want to go to 44.....scroll .
View 2 Replies
View Related
Oct 9, 2012
Started freezing when selecting a layout tab. Other programs respond but not C3D. Seems to be this one drawing - pretty simple, about 1000 pnts, and a surface so far. When I select the layout tab it switches and I see a few contours but C3D does not respond. First time I have exp this.
Civil 3D 2013 SP 1, 64 bit
Dell Precision T5600, 16 GB
Win 7 Professional 64 bit
Intel Xeon @ 2.0 GHz
NVIDIA Quadro 4000
View 2 Replies
View Related
Apr 30, 2012
Is there any chance to fit plan and profile on one 11x17 layout without exploding and export to dwg? I can't do it because of annotation scale that change every time.
View 4 Replies
View Related
Jun 24, 2011
Our firm has finally decided to leave LDC 2009 behind and moving to C3D 2012.I would like to ask a few questions about the way plan and profiles are created with C3D.
In LDC, we would create a full profile that included everything in it, that is proposed and existing centerline elevations and left and right top of curb elevations. Then on the sheet layouts, we would make many viewports that showed the proposed and existing sets, that is centers, lefts and rights. (medians in the example attached)
I've been watching many online videos on how to sample center, left and right and how to create a proposed center line but I can't figure out how to make a proposed left and right profile so that I can control drainage into existing inlets.
View 8 Replies
View Related
Jun 15, 2012
I am using 2013 and it wont let me rename the layouts . I have just 10 layouts and it will let me rename one but not the others. The others just flash the little blue color and back to black.
View 2 Replies
View Related
Oct 11, 2013
I have a Civil 3D project with piping networks, grading etc. The servicing and grading plans are on layout tabs (5 of each 10 in total). When I would go export layout Civil 3D would go into not responding mode and crash. This caused quit a bit of stress as we had to get the drawings out to meet a deadline.
After investigating this issue, we identified that we had save our layer states in the layer manager. Delete the viewport on the layout tabs, draw a new viewport and then reinstate the layer states for each layout. This resolved, the crashing issue.
Civil 3D 2013
Windows 8
Intel(R) Core(TM) i7-4770 CPU @ 3.40GHz
32. GB
64-bit Oepration System, x64-based processor
View 9 Replies
View Related
Aug 20, 2012
I would like to be able to access the new north arrow feature of Map 3D 2013 to my Civil 3D ribbon but I can not find which ribbon element to add. How can I accomplish this?
View 3 Replies
View Related
Jan 12, 2009
My layout tabs are missing. How do you get them back?
View 9 Replies
View Related
Nov 12, 2013
I clicked "Hide Model and Layout Tabs" to see what it would do, and now I can't get them back. Not only did I lose them in that drawing, I lost the tabs in EVERY drawing and EVERY version of C3D. I googled the problem and every forum says the same things, and I've tried them without success:
Options >> Display >> Layout elements >> Display Layout and Model Tabs
CUI >> Workspace Properties >> Model/Layout Tabs >> On
I'm lacking a couple of icons on the lower tray to the right of the Model/Paper button.
The baffling thing is that I've lost the tabs on ALL versions of C3D. Is there a magical command line entry that will bring back my beloved tabs?
HP DV7 Laptop
Intel Core i7-3820QM 3rd Generation Quad Core 2.7 GHZ CPU
16 GB DDR3 RAM ( 2 DIMM ) / 180 GB SSD
Nvidia GeForce 650M Graphics w/2 GB Memory
Windows 7 Professional 64 bit / AutoCAD Civil 3D 2014
View 9 Replies
View Related
May 2, 2012
i used to open file off like 6.5 mb size easly and i have a save as version of it and it open very fast and normal , yet nowi'm stuck for like 15 mins on "Regenerating Layout" in command line...
and it only happen with this file also my RAM usage went beyound normal ?! So what to do ?
View 2 Replies
View Related
Mar 6, 2012
When I draw in the profile layout I'm getting odd results when the labeling is placed. See attachment. I have been looking through the styles trying to find what is wrong.
View 9 Replies
View Related
Mar 11, 2013
I have an alingment and profile, but I cannot use the layout tool to create a curve (vertical)...what I am doing wrong. I select the profile in profile view and right click to select "edit profile geometry" and get the layout tool bar but cannot select to draw a curve...
View 8 Replies
View Related
Feb 4, 2013
Is there any way to turn off Layout Tools Contextual Tab in 2013? I tried the same options that worked for 2013, but it didn't work on 2013.
View 1 Replies
View Related
Jul 30, 2013
Is this still an issue in Civil 3D 2014? (Looks like it's been broke since Civil 3D 2007). URL.....
View 9 Replies
View Related
Feb 7, 2013
I am working on creating a set of plans and have a couple of note pages that are generic and will not need to be change. I am creating a template with layers, layout tabs, styles, etc. I am trying to put these notes straight into a layout tab just simply by pasting them in there. The issue I am having is with the hatching on a couple of objects, the hatches appear correctly right off. When I save the drawing and reopen the hatches are a solid block, regen does not fix this. I can however explode the hatch and then undo the explode command and it appears correctly. Is there a way I can make the hatches appear correct everytime?
View 3 Replies
View Related
Jul 10, 2012
I have created an alignment, and have the stationing labels on a different layer than the actual alignment linework. I have frozen the layer with the alignment on it in a viewport, but not the layer with the labels. However, when I regen, the labels disappear. I need to have the labels visible, and the linework off.
View 4 Replies
View Related
Jul 19, 2012
Having issues with where the first section view starts when trying to place multiple section views on sheets. The problem I am having is that the offset from the bottom of the sheet frame seems to be a half unit off and grid lines will not line up with the sheet gridlines we have developed. I attached a pdf of the resulting offset. what I need to look for to adjust the bottom offset?
View 2 Replies
View Related
Jun 4, 2013
have a diesel expression that would read a layout tab? for example if i have a layout tab names 244180101 I would need it to read the last 2 digits in the layout tab.
AutoCAD Civil 3D 2014
HP Z620 Workstation 64-bit
Duel Intel Xeon E5-2620 @ 2.00 GHz
Ram: 48 GB
View 9 Replies
View Related
Jul 5, 2012
What would be the best way to edit a pipe network's layout (pipe position, pipe slope, structure height, etc.)?
The easiest way I can think of is to create alignments of all the pipes in the network and then editing the grips in the profile view of each alignment, easily changing the pipe's slope and depth...
The catch with this method is that:
- it takes a while to create all the alignments needed;
- I have to manually adjust the alignments if I need to change the pipe network position on plan.
Using Building Design Suite Ultimate 2014
View 9 Replies
View Related
Apr 9, 2013
When creating plan and profile sheets is it possible to create the plan view with the alignment moved down to show more of project above the alignment? The default setting puts the alignment at the center of the plan view window.
View 2 Replies
View Related
