I am creating profiles and I can not get the existing grade linetype to show up as a uniformed dashed line. The layer is set up for a dashed line but the existing profile line is made up of too many nodes to make the linestyle look right.
View 9 Repliesi have a corridor. the corridor feature line that is supposed to hit the proposed centerline is following my existing grade instead of where the profile is. in other words, the corridor line i need at the centerline when i do "feature lines from corridor" is following my existing grade instead of the top of my road. did i accid. change something? i need it to follow the top centerline of my road. the red arrow is the line i need at the top centerline.
View 3 Replies View Relatedi created section view as in pic1. In Bands, Existing surface elevation labels at existing surface grade breaks, top of road elevation labels at top grade breaks, datum is the same. Can i add existing surface elevation labels at top of road grade breaks? (pic2)
View 7 Replies View RelatedI am trying to label existing ground & profile grade on my cross-sections the way old Land 4 used to do it. I've muddled through section view property style settings, band settings, group properties w/no luck. It can't possible be this difficult. What am I missing?
View 5 Replies View Relatedcreating a existing surface single Curb/Gutter spot elevation label using two existing surface elevation points and not cogo points. I am a surveyor, and I want to be able to just click on both points one at a time (top of curb/gutter) to place the elevation label.
View 3 Replies View Relatedi was wondering is it possible to show slopes or grades on my surfaces , or corridors IN PLAN VIEW ?
View 8 Replies View Relatedi've got a profile band for my finished grade profile. it works great except for where a pvi falls at a major or minor station, the profile band is blank. is there a way to get the finished grade elevation to show in the band at a pvi?
Dell Studio XPS 9100
Intel Core i7 CPU 930 @ 2.8GHz
12GB Ram
64 bit
C3D 2012 SP3.0
I am trying to create a new linetype using arrows to show the direction of a flow. I can get the outline of my arrow head to save as a shape, but have not figured out how to save the hatching to show up in a linetype. I need the arrow head to be shaded in solid. Also is there any downloadable linetypes out there for Civil 3D?
View 5 Replies View RelatedI'm currently working on a profile and I just don't understand why my profiles barely show any stations. It doesn't even show the very first station. I remember checking on a box that mentioned showing the 1st station and still nothing. I've gone into the edit band style and turned on the labels at minor stations but it just turned on the FG/EG elevations.
I've added a picture showing what i'm talking about. It only shows stations 31+00 and 32+00. Not 30+00 or the 50' increments. Also, while I'm on the subject. How do I get something proposed into this existing profile to show FG Elevations. Example if I just wanted to strike a straight line from 30+00 to the end where the elevation is a 91' & 86'.
HP Compaq 8100 Elite
Win 7 Pro SP1 - 64Bit
8GB RAM
i7 860 @ 2.80 GHZ
AutoCad Civil 3d 2012 SP1
I need a line to show a fence and it should be a line with a / poking out on one side like -/-/- but the lines in between longer and the side lines just on one side...
How to make one like that or where I can find one?
Why new rooms show up in lieu of existing rooms when"show previous and demo" are set for the phase filter? Every single other existing element including doors, walls, windows, etc. show in the "show previous and demo" phase filter with the exception of rooms.
View 5 Replies View RelatedI'm working on a grading plan which excavates down from just outside the waterline of an existing pond. When I create a surface from the grading, it looks like a whole bunch of strange break lines have been added, messing up the surface. I thought it might be the mid ordinate distance but changing that doesn't seem to fix it it. Interestingly, when I grade from the original waterline, this doesn't seem to happen.
Here is my workflow, a picture of the result is shown below.
1. Turned the current waterline into a feature line.
2. Created new feature line by offsetting outside that feature line by 3.16 ft.
3. From new feature line, grade down 10 feet at 3:1
4. Create new surface using grading.
The grading lines (shown in white) look correct. But when I create the surface (green and yellow), it is all messed up.
I want to create a grade (without object grade) using a corridor. This is my assembly:
This only contains the sub assembly "DaylightBench" in the side right.
I have the alignment and profile. I have created the corridor.
red line= alignment
green line= feature line (code Intersecction) converted to polyline.
pink surface= surface (code TOP).
I have added a boundary for surface of type "add from polygon" and I have selected the closed polyline(green line).
However, the boundary seems doesn´t work.
Autocad Civil 3D 2014 +SP1
Quad Core Intel i7 3770-cpu 3.40Ghz.
ssd samsung 840 pro 512gb+ssd samsung 840 pro 256 gb+1tb hdd
32gb RAM 1600 Mhz.
nVidia Quadro 2000.
Win 7 Pro 64bit
I have a profile set up with a surface an alignment and a Water Main. I would like to place grade breaks (Using Profile labels) every 100' along the surface however the increment field isn't available for grade breaks. Weeding doesn't work because it needs to be exactly every 100' I was thinking of creating an expression for it however I still haven't reached that level of expertise.
View 5 Replies View RelatedI noticed a post a few years ago mentioning this function wasn't available then. Is it still not available? Is there a routine? A lisp? An expression that I can make to put a slope arrow inside every tin in my surface with a % grade?
View 1 Replies View RelatedWhy do profile grade markers always reset in section views? This has to have been a wish list item. lsp or software to populate these? I heard in 2014 they still disappear.
Civil 3D 2012 SP4.0 Windows 7 Enterprise 64-bit
C3D 2014 SP1
Dell M6600, Core i7 @ 2.3GHz, 16 GB ram
Dell T3500 workstation, too much ram
I'm trying to create an all new existing surface over existing ground. I have a TIN surface of the EG, and I have drawn overlay splines that describe the new surface, but how to go about creating that design surface.
It is a compound surface, open on one end and closed all around on the other, somewhat like a half of a football stadium, but with an irregular upper edge because I am needing to figure out cuts and fills to manipulate the EG into this new surface without costly major terraforming. There is about 40-50' vertical elevation between the "field" and the upper rim with a generally constant 7-10 deg. slope all around. I'm just at a loss to figure out how to approach this project, and am quite new to Civil 3D.
Civil3D 2013
MacBookPro 17 - 2.4GHz Intel QuadCore i7 (Late 2011 build)
Microsoft Windows 7 64bit
350GB Bootcamp volume
I was laying out a vertical curve in the roadway profile. I have a vertical curve of 100' in length, however immediately after that it shows a grade break. I do not want this grade break in my profile, I simply want a vertical curve with two grades on the left and right sides. How can I get 2009 C3D to remove the grade breaks? It would be very uncomfortable for someone to have to drive over these in the real world.
View 1 Replies View RelatedI was wondering if there is a way that I can take an existing grade surface and apply a designed pond surface.
Right now I have the pond as a set of 3d Polylines in the proper geometry.
I want to place the pond into this surface and cut/fill at a 3:1 from that pond to the existing surface.
We are working on a road widening scheme where one edge of the road is retained as far as possible while other edge being widened. I like to design a retained channel line by extending the cross fall between the existing center line and the exiting channel line on to the design one.
It is possible in civil 3d to extend the gradient between two feature lines at some offset from reference feature line?
i've got a profile with a lot of grade labels, some of which i've turned the visibiliy off. i need to turn some, but not al,l of them on.
Dell Studio XPS 9100
Intel Core i7 CPU 930 @ 2.8GHz
12GB Ram
64 bit
C3D 2012 SP3.0
I have labled for grade break on the profile, but it did not lable all break line? how to add grade breaks along the new profile (see attached image).
View 1 Replies View RelatedI've got a drawing in which the existing ground is so jaggedy that I've got way too many grade breaks (see the attached image). I know I can use the weeding and eliminate the labels every 50 feet, or so, along the profile. But I need to have the ability to only show a specific grade break range. For instance, I'd like for my profile only to display grade breaks between 0% and 2% and not to display anything above 2%. I've tried making an expression, but have been hitting brick walls. I also know I can manually (use the CTRL + click) select the specific labels that I don't want and erase them, but I've got lots of these labels. Any LISP routine or an expression that can accomplish this? [URL]
View 9 Replies View RelatedI have a surface that I have done a slope analysis on and want to put a table showing the slope grades. I have made a viewport and would like to put the table in paperspace. However, when I zoom in paperspace and regen the table changes size. How or where do I keep the table from changing size. It wont let me scale it up or down.
View 3 Replies View RelatedHow I could create a label for the curb return grade as shown on the attached file. The label is on a curve.
View 6 Replies View RelatedHow do I get my finished grade on ALL my cross-sections at once? I'm getting the existing grade for both section 1 and section 2 grade in the band.
View 3 Replies View RelatedWhen we created our fist C3D template in 2007 it was possible to make a grading criteria that targeted a surface at a fixed distance. In other words, the slope was variable. Looking at it again in 2013 it appears it's not possible to creat a criteria like that. Am I missing something? Or was that option removed? .....perhaps because it was too unstable?
View 9 Replies View RelatedI have a regular AutoCAD line in a profile view and wondered if there is a way of labeling the grade of the line. I'd think I could use and expression to calculate it. But I don't know how to automatically adjust for the vertical exaggeration without having to have a separate expression for all possible situations.
View 5 Replies View RelatedI had thought this would work with no problem. I know the elevation I need to start an arc at and an elevation at a point along the arc. I drew that portion of the arc and then extended the arc to a line where I need the arc to end. I had expected the arc to extend along it's current grade the way a straight Feature line would. But the end dropped to 0.
I undid the extension, listed the FL arc to get the grade, extended it again and used the Elevation Editor to set the previous grade. But why didn't the extension work? I checked for other FL in the site that might cause this but there were none.
I'm building up my assembly and I want to add a daylight sub-assembly in order to grade my proposed surface to the existing surface. Typically I would have a 1:3 slope up or down. I have choosen the DaylightGeneral for this and although there is quite a few parameters to play with, I'm only interested in the up/down slope but when I put anything sleeper than 1:4 it doesn't work, I get this red line and circle.
View 4 Replies View RelatedDesigning a tailing dam I use a corridor model changing slope grade from 1:2 to 1:2.5.
There are assemblies and subassemblies with shapes defined for each slope grade, LinkMulti with no target, but how do I make the transition from one slope grade to another one?
In corridor properties I included two regions for each slope grade.
For grading there is a transition function. But the transition for corridors?