I am trying to create a new linetype using arrows to show the direction of a flow. I can get the outline of my arrow head to save as a shape, but have not figured out how to save the hatching to show up in a linetype. I need the arrow head to be shaded in solid. Also is there any downloadable linetypes out there for Civil 3D?
View 5 RepliesToolspace > Settings > General > Label Styles > Line
When I create a line label, one of the components available is “Direction Arrow”. This component is not available for “Curve” labels. I would really like to use C3D labels to indicate direction (I realize curves don't have a 'direction', but I don’t mind manually flipping and reversing the arrow). Is there any other label option in C3D that will draw a direction arrow for curves?
I can't figure out how to reverse the flow direction on my pipe so I was going to just redraw it but after I delete a pipe and rt click to edit network the "add pipes and stuctures" won't let me add anything. I'm just guessing I need to reverse the flow direction because my invert out and invert in elevations are backwards in the profile. I'm working in Civil3D 2012.
View 6 Replies View RelatedIs it possible to have pipe flow direction method set to "by slope" by default when we creating new pipes?
View 5 Replies View RelatedNow, in my understanding, the flow arrow should either be rotated 0, or 180 (pi radians). But clearly, some of them like to have their own mind about things, and decide on some other rotation. It seems that on the steep slopes, the arrows go a bit skew.
I think the skew is related to the actual elevation difference of the segment, rather than the steepness of the slope. A long segment with 15% slope has a worse skew than a short segment at over 30%, presumably because the elevation difference from the start to the end of the segment is larger.
I can't seem to find where to increase the flow direction arrow size on a watershed. Am accessing remotely, it's a bit laggy and bothersome, but doable. I looked all over Toolspace.
View 3 Replies View RelatedI have utilized the "old school" Flow Line Lintetype (with the ARROW that is never really centered) for many years
I have been trying to acquire the preferred FlowLine Arrow Linetype (complex with the arrow shape)
So far, I have not succeeded. What is the easiest way to obtain/create this preferred linetype ? (arrow directions change with the direction of the polyline)....
how to show arrows (solid or stick) between vertices in Profile views. It seems other design packages can do it so I hope C3D can as well, however I can not find anything detailing if it can be done or how. I attach and example so you can see what I mean. Arrows show sections of differing flow/pipe size & grage for each pipe.
View 1 Replies View RelatedI am creating profiles and I can not get the existing grade linetype to show up as a uniformed dashed line. The layer is set up for a dashed line but the existing profile line is made up of too many nodes to make the linestyle look right.
View 9 Replies View RelatedI've got GIS shape files for sanitary sewer pipes and manholes which contains object data for the upstream and downstream inverts on each pipe as well as the lowest invert at each manhole. Ideally, I would like to add an arrow to the pipe showing the flow direction in the sewer. i know I can use the annotation template to label the inverts, but is there a way to automate the process to add the direction arrow?
View 3 Replies View RelatedHow to switch the direction of text arrows?I’m wondering if there is a way to switch the direction of the text arrows from being left directed to be right?
View 4 Replies View RelatedI have a linetype
*DIVERSION_LARGE,diversion large ---- >> ---- >> ---- >> ----
A,.5,-.2,["<<",standard,S=.15,r=0,U=0.0,X=-0.1,Y=-.05],-.2
when I draw a polyline, or use it as the linetype in a feature line style, the arrows seem to revrse whenever there is a change in direction any significance. Also, the reverse command and reversefeature command have no effect. Rotating a segment does not change the direction. I know I must be missing something.
In the attached, I have a feature line, and a polyline that the arrows change direction when the feature does.
Windows 7 64
Intel Core i7 2.0 GHz 2.0 GHz
8 GB RAM
Nvidia GeForce GTX460M
Civil 3D 2012 SP2.1
I am trying to create a linetype(actually multible linetyes) for Civil drawings. I need the line type to have the following text..........12" W. I have tried to edit and existing linetype but for some reason the string does not seem to like me using the inch (") symbol. Any proper way to generate this linetype and I should be able to edit it to get all the other line sizes I need.
View 5 Replies View RelatedFlow segment label using total Flow Type travel time for each segment:
C3D 2014 SP1
W7x64; i7 8gb; Radeon HD 5700
[URL]....
I have cut several sections at different points along a road alignment. The sections are cut facing the same direction as the alignmnet. Is there a way to reverse the section direction without changing the alignment direction?
View 6 Replies View Relatedcan I place a direction arrows on 3D polyline in dwg files? In 2D, it is very simple.
View 9 Replies View RelatedI need a line to show a fence and it should be a line with a / poking out on one side like -/-/- but the lines in between longer and the side lines just on one side...
How to make one like that or where I can find one?
I created a new surface, pasted my OG surface into it, set the build to exclude elevations less than and greater than but my surface still is showing every contour range. I want to only show contours at elevations of 371.5 and 370.5
Is it because it's a pasted surface?
Sometimes when I plot/publish a DWF or PDF the arrows extend past the extension lines. I need the point of my arrows always end at the extension line?
View 1 Replies View RelatedWe have a waterjet and machine shop at my place of employment, and currently my work flow is to draw the parts. Then for parts that need material left for machining I create a new part and using the derive tool I place my base part which I then apply extrusions to fill the holes and use thicken to add material to the surfaces that need machining.
View 4 Replies View RelatedI am working on a large park project. I have a proposed and existing surface. I have created a volume surface to show elevation banding with cut and fill ranges. I need to create a drawing for someone who doesn't have civil 3d showing all the "cut" areas. They really want a boundary of hatch. What is the best way to do this after I change my analysis to -30 feet cut to 0 feet cut.
View 9 Replies View RelatedI have a client that wants to put in a constant flow into an inlet and have SSA calculate the HGL downstream of that (as well as add additional flows at additional inlets). Is there a way to do this? I tried adding an "Initial flow" to a pipe but after running the analysis, that flow wasn't the peak of the pipe (I used 1cfs for the initial flow and the peak was 0.77 cfs).
View 6 Replies View RelatedHow to create a revolve surface in an assembly for the purpose of measuring a flow area through a specific area? See the attached JPG, I basically have a conical internal diameter with a pin protruding into it..... I need to measure the flow area as shown in the sketch attached here. the way I have this shown in the attached JPG is the way that we had previously performed this in Pro-e.
View 9 Replies View RelatedI am modeling an existing storm system that is under capacity. After running the model, some of the flows seem to be incorrect. I have one section that has a known flow of 1.31 cfs. The results for this pipe section shows 28.82 cfs (peak flow during analysis) and 6.06 cfs (design flow capacity). The pipe section is a 15" with constructed slope of 0.0088 ft/ft. The max velocity attained is 23.48 ft/sec. I know that the downstream is undersized. Could this flow rate be caused by the downstream backflows? The model is setup as hydrodynamic and rational method. My inertial terms are set at ignore, time step = 0, junction surface area = 0 and variable time step with safety factor 75%. I have gutter bypass flows and my sag structures have ponded area set at 100.
View 8 Replies View Relatedhow to create a moister steam flow similar to the image attached,is there some some plug-in or other way of doing it easily?
View 1 Replies View RelatedHow i would create a new linetype in AutoCAD LT 2004. For example creating an electrically traced line that is a dashed line with the letter E in the line.
View 6 Replies View RelatedI looked through other threads and I still couldnt get it figured out. I am trying to make a linetype like the attached image..
View 7 Replies View RelatedI noticed a post a few years ago mentioning this function wasn't available then. Is it still not available? Is there a routine? A lisp? An expression that I can make to put a slope arrow inside every tin in my surface with a % grade?
View 1 Replies View Relatedwhere the setting is to reverse the flow of a pipe. I have the flow arrow shown in the wrong direction plus am showing a negative slope on a pipe, which should never be done.
View 9 Replies View RelatedI have a huge subdivision that we are about to do in civil 3d. The subdivision has over 1800 lots. I am wondering what is the best way to go about this. At the moment we are thinking we have to do the alignments, profiles and corridors all in one design drawing for it all to be dynamic? If so this file is going to be huge. Is there a way we can split it up and still keep everything dynamic?
View 9 Replies View RelatedWhere can I find all the column types that are found in the different report types so I can use them in custom reports.
View 1 Replies View Related