AutoCAD Civil 3D :: Using 4 Points To Create 4 Lines And 1 Parcel
Sep 18, 2013
I have 4 points (from "Points from file", I created Points #1, #2, #3 and #$ in the non-linear fashion).
1) I want to create 4 straight lines (connecting Pt#1-Pt#2, P#2-P#3, P#3-Pt#4, P#4-P#1) by using some Commands. What Commands in the Command Line should I use to create these 4 straight lines from these 4 points?
2) I want to create 1 parcel (connecting Pt#1-Pt#2-Pt#3-Pt#4-Pt#1) by using some Commands after "Parcel Creation Tools" => Draw Tangent-Tangent with No Curve is clicked. What Commands should I use in the Command Line to specify these points to form a parcel?
I need to create points with surface elevations along sample lines. The points need to represent the verticies one would see in the section editor. I've attached an image of my section editor for one of my sample lines. I need to create points that represent these 24 verticies along this sample line and do so for the rest of my sample lines as well. Is there an automated process to create these points?
I need to make a map of a subdivision with all lot dimensions. I see how we can label all the lines of a lot by picking the parcel label, but it only allows one at a time.
I make parcels in a base dwg and make separate layers for each parcel and labels moving them off the default layer zero.
i xref the base and then try freezing all the parcel layers and the go away but i am left with a copy of the parcel lines on xref layer zero with no control over it.
Create Parcel Segments using the Slide Angle Create command Create a Feature Line in the same Site that bisects any/all of the Slide Angle Create Segments Save, close and reopen the drawing Parcel Segments now terminate at the intersection of the FL
Not sure if this is as designed, and I don't recall this behavior in 2007. We have used FLs to assign elevations to Parcel Segments in 2007, looks like this is no longer possible.
To workaround the missing API for creating Parcel Area Tables, I have tried the following:
1. Create a "pick point" selection set (using ObjectARX), containing the Parcel for which I want to create a table. 2. Execute the AddParcelTable command. 3. Programmatically push the Select Parcel-button and the OK button of the Create Table dialog using win32 API.
When the Select Parcel button is pressed, the label next to it displays 1 parcel(s) selected and when the OK button is pressed, Civil prompts the user to pick the upper left corner of the table, but the prompt is immediately interrupted with the message "Invalid 2D point" and the table creation is aborted...
I have a record plat drawing with multiple parcels and parcel styles. For my lands of the grantors I view port froze the lots and right of way layers from my parcel styles. I don’t want to show them in this viewport. To my surprise the lines show up in the object layer we have set for parcels. This was not the case in 2011. We are in 2014 with the first hotfix update. I understand putting the parcel styles in the object layer, but why another mysterious line under it? I did create parcels from objects, but had them erased when I created them. This did not matter either way. Is there a way to get rid of them? I did put them in a new layer, set it to “No Plot” This kept them from plotting, but I really don’t want to have to take the time to do it.
I had to create a boundary map and place points to all corners. How to export these newly created points back into my data collector (Ranger) and also I'm trying to figure out how to print out a points list.
I stumbled on to this thread but I guessing that it's a different CAD year because my modify tab doesn't look like this. URL.....
When creating and labelling a parcel Autocadd Civil 3d places a label in an adjoining area outside of the intended parcel.
The label seems ubrelated to the intended parcel and is labelled with a diferent parcel number, area, etc.. No additional parcel boundaries seem to be created.
Have created a closed polyline for parcel creation as well as a number of other steps to ensure that there are no breaks in the enclosed parcel.
How to create points at the vertices of the lines in the regular AutoCAD? ’m wondering if there is a way to automatically create points at the vertices (or only at the end points) of existing lines (or polylines)?
How do I draw 2D lines from points? What setting do I need to change? I want to drawin glines using the node as a grip but I do not want them to have z coordinates.
Is there a way to link feature lines to points? If I have a series of points and I've joined them with a feature line; I want the feature line to update automatically if I adjust a point elevation.
Making the switch to Civil 3D. I was previously using 2009, and I could add dimension labels by picking two points (endpoints, intersections, etc.) to get the whole line or just a segment. In Civil 3D 2012, I create styles and add labels through the annotate tab, but I can only selct the line or curve in its entirety. There must be a way to easily label portions of a line or multiple segments as one line.
When I start to draw my polylines to cogo points I have inserted in my drawing it keeps wanting to hang up when I hover over the point. I have set up my point styles to bring in our points with all the attribute information so I am thinking it keeps trying to read all that info as soon as my mouse hits it..
I saw a post about rollovertips but that did not change anything. Any ides what might be causing this? Im using Civil3D 2011.
Problem with command from Home tab - Draw panel - Curves drop-down - Create Curves Between Two Lines OR Create Curve on Two Lines.
If you select the Degree option, it draws a zero length curve when you type in a valid number for degree of curve. I have tried entering it in decimal format and as ##d##'. NOTHING WORKS!
I have a GIS parcel file that I have connected to. The file works fine, but when I change the linetype from continuous to a center or dash-dot linetype I have trouble. The parcels are all closed polygons so everywhere the parcels touch, the parcel lines overlap and the linetype is very disjointed. Instead of looking like a "center" line, it looks like a solid line with a radom gap here and there.
I wanna interpolate points from surface but only in that area where my sample lines intersecting with the surface. There is a point creation tool that makes this based on polylines but I have to many data and it will get to much time to do this. So, for better understanding I attached some pictures, in the first picture it is shown the final result which I have made based on polylines, but here is also a problem, the tool is not putting points where the surface is changing ( on my second picture I highlighted with red circles).
If I list one of the objects, it is defined as a block. I have repeatedly tried to explode this but to no avail.
My intention is to convert these AutoCAD "points" as points in Civil 3D to process them further. When I use Points>Convert AutoCAD points commands, it returns me a "invalid selection" message.
How do I explode these blocks and convert them to Civil 3D point objects?
I am working in a .dwg that i have previously created cogo point in, but now when i try to created cogo points manually, it goes through the prompts, but will not create the point. P.S I am using Civil 3d 2011
My boss wants everything plotted with lines merge, however, all of my parcel labels will not plot with the text masked. The mask plots fine when it is set to lines overwrite.
I was wondering if there is a setting somewhere that can be turned on to display the manual points I am creating as I create them instead of having to go back and update the point group before they display in the drawing?
I have the need to put COGO points along the vertices of multiple 3D polylines in a DWG. I know how to do this individually for each 3DPL via the "Points>Create - Miscellaneous > Polyline Vertices - Automatic" or "CREATEPTPLYLNCTRVERTAUTO" command. Need tip on how to do this in a batch format for all the selected 3D PLines in the drawing without having to select each individual 3DPL and having to hit return to enter a description for each individual vertex? I can do without having to add a description and can leave each description blank or enter the same description for each.
I want to create new vertex points in feature line and 3dpol.
I have this: try { if (obj.GetType() == typeof(Autodesk.AutoCAD.DatabaseServices.Polyline3d)) { Polyline3d p3d = (Polyline3d)trans.GetObject(entRes.ObjectId, OpenMode.ForWrite);
always catches the same Exception "the value is not within the expected range" .I have translated it because I get "El valor no está dentro del intervalo esperado". Perhaps is this: " Value does not fall within the expected range.".
I have tried it with different point3d values but always catches Exception.
With pol3d I have similar problem.
Autocad Civil 3D 2014 +SP1 Quad Core Intel i7 3770-cpu 3.40Ghz. ssd samsung 840 pro 512gb+ssd samsung 840 pro 256 gb+1tb hdd 32gb RAM 1600 Mhz. nVidia Quadro 2000. Win 7 Pro 64bit
I want to use the 'Create Points at Alignment Geometry' tool in order to label only the PIs. However, when I use the tool it creates two points (one called PI and one called CPI) at each vertex of the alignment. How can I fix this issue and toggle the creation of the various other geometry points?
Is there a way to create a point group of random points within a drawing and adjust the elevations for the points within that group? Some of the points in the group may have been manually created and some may have been imported by way of "Import Events"..
Is there a way to create automatic Point Groups when importing points? Sort of like a Desc Key for layers? I know it probably is impossible but I have to ask.
