AutoCAD Civil 3D :: Typical Road Subassembly Carriageway Missing Parameters?
Feb 5, 2013
I am just having some difficulties using the standard UKIE subassemblies where the carriageway is not showing the parameters correct. See the drawing attached. Eg:
1) The properties does not show the side correctly it has a zero value (not much of a issue as i can use the mirror command) (drawing subassembly)
2) I am unable to choose any superelevation on the subassembly . Now this is what causing me problems.
I have already re-installed the software from scratch and have also downladed the latest service pack.
View 8 Replies
ADVERTISEMENT
Aug 1, 2013
I am using one assembly for this project and of course the existing surface does not always work well with one assembly so I have been using the corridor section editor to adjust each station individually. Attached is a picture of my first station, I started with a 3:1 fore slope (left side) and have changed it to a 2:1 slope. However, my ditch line elevation did not adjust and my parameter editor will not let me adjust the beginning elevation for the ditch line. I am curious as to what the simple solution is for this so my ditchline and back slope or slope to surface will be portrayed correctly.
View 4 Replies
View Related
May 12, 2013
Is there a way to change programmatically parameters of applied subassembly?
View 1 Replies
View Related
Jun 25, 2013
Is it possible to change the parameters of a subassembly - for example in an assembly comprising several subassemblies, can I change a parameter in Subassembly.LaneOutsideSuper, for example, to vary the Lane Width from 4m at CH90 to 3.25m at CH160m and keep it at 3.25m for the rest of the corridor.
I am new to Civil3D.
View 3 Replies
View Related
Jan 12, 2014
Is it possible to create subassembly from C3D Stock Subassemblies.dll programmatically using .NET? I need call procedure (Basic Lane for example), set all input parameters and create subassembly in drawing.
View 7 Replies
View Related
Jan 15, 2013
When i am creating a assembly, the sub assembly parameters for the generic pavement structure is not showing (such as the lane width or crossfall) Other sub-assemlies show these parameters. Is this a bug or is there a way i can turn this on.
I can change the parameters on the properties.
View 3 Replies
View Related
Mar 13, 2012
When I created my subassembly with subassembly composer, it's difficult to change the sequency of the input/output parameters. Do we have an easy way to do that, Like moving?
View 4 Replies
View Related
Jan 9, 2013
When I open up Cooridors/Sub Assembly Tool Pallets all the imperial and metric sub assemblies are missing.
View 2 Replies
View Related
Nov 1, 2012
in this image, I am showing the Options dialog box of AutoCAD Architecture 2013. This was a typical installation, no customization at all, but several icons are missing, showing just a question mark instead.
View 3 Replies
View Related
Sep 10, 2013
I am trying to determine the volume of material (cut/fill) for a roadway surface in C3D 2013 using the volume dashboard.
I have created a fictional surface, basic profile and assembly so I can compare my calcs with C3D. After creating my surfaces and running the dashboard calcs, the program calculated the correct cut/fill volume. However looking at the surface in iso, I saw that additional surfaces were produced around zero elevation - refer to attached snapshot
In my actual model, I am well above zero elevation but these additional surfaces could cause problems on other projects.
View 2 Replies
View Related
Aug 21, 2013
I need to model road with same elevation. But also need to model ditch along road which has a slope of 0.2%. how can i make a ditch with slope.
View 2 Replies
View Related
Nov 12, 2013
When I use ImportSubassembly API to import my subassembly created by Autodesk Subassembly Composer into my civil project, it reports error-"eFilerError".
the code like this:
atcFile = @"D:9f92eaa4ef514ac982518852e1169932.atc";
itemId = "ab660722-c69d-4ade-b373-0e9f99c94e55";
SubassemblyCollection subassemblyCollection = cDoc.SubassemblyCollection;
ObjectId subassemblyId = subassemblyCollection.ImportSubassembly("TestSubassembly", atcFile, itemId, this.doc.Editor.GetPoint("Select import subAssembly location").Value);
However, it is OK if to import subassembly provided by Cilvil 3D.
View 9 Replies
View Related
Mar 26, 2009
I am looking to draw my pipe with a thicker appearance than the typical line of width "0". Our storm pipes are usually drawn with this so as to stand out from other utilities. If the pipe is represented by a polyline, I have usually adjusted the "Width" or "Global Width" value to my liking. With pipe objects, it seems more complicated. I have searched the settings, and the closest thing that I could find was the Lineweight property, but that appears to have no effect on the line thickness in the CAD drawing.
Do I need to tweak a plot setting? Make a new linetype altogether?
View 6 Replies
View Related
Jan 30, 2013
running an assembly in to the road corridor and creating a surface. i have designed a network of Roads in CIVIL 3d in which whole network is surrounded by a Loop road. The loop road cross fall is unidirectional (2%) and 4.5 wide. I have used LaneOutsideSuperWithWidening subassembly to create the assembly of the road. This doesnt contain any kerb or footpath but only road channel lines, The corridor run soomthly but after creating the of the loop road corridor the surface is becoming flat meaning there isn't any cross fall acoss the road but in the assembly crossfall is there. If i run the same assembly in another road alignment the suface is coming absolutely correct.
I also tried different road assemblies to run along the loop road but the result is same no cross fall across the road.
View 2 Replies
View Related
Feb 1, 2012
I am working on Street Improvement Plan using Civil 3D 2012. I have my centerline stationing set for major (100') and minor (50'). My street plan is kind of busy with a several call-out/label, leader etc. I want to set my my station for both major and minor with with decimal to read as 1+00 or 1+ 50 as opposed to 1+00.00... How to get rid of the decimal points.
View 6 Replies
View Related
Nov 4, 2013
Road design civil 3d complete files (Plan, Profile with complete band, Assembly , corridor, sections etc .
View 5 Replies
View Related
Nov 19, 2012
I have make a road network. Then i make a corridor surface using corridor extends as outside boundary. I also create a boundary in the interior side of the roads with interactively tool, and i use it as a hide boundary. The corridor surface look fine but when i am trying to make a finish Ground Surface pasting the corridor surface after Existing Ground surface then the hide boundary of corridor surface make holes in finish Ground surface.
View 3 Replies
View Related
May 30, 2013
Is this a desired behavior on a multileader? URL....
Seems to do it for anything that is not left aligned. I think it was present in 2013 as well. I use multileaders for annotations a lot since it is easier to use them with the background masks and borders than mtexts.
View 5 Replies
View Related
Dec 10, 2013
I am creating P&P sheets for my road. I created view frames, and when I got to create sheets, I pick "all layouts in new drawing". I go to open the new drawing up, but all that shows up/tranfers is the profile and alignment, nothing else comes over ( proposed linework, existing linework, etc.)??????
View 4 Replies
View Related
Feb 27, 2013
I am new to Civil 3D and need to customise the look of road profiles so they look like they were produced from any of our other civil design software packages that we use (to maintain standards between offices etc).
The attached picture is what I need them to look like. I want to show both the natural ground (the dotted line) and the design road line (solid). Then I want to write on the profile the station, natural level and the design level.
I've got the Mastering Civil 3D book (and a few others) sitting on my desk.I worked out how to turn off the grid on the default profile althoguh that was about it.
View 1 Replies
View Related
Apr 24, 2013
is it possible to break surface in SAC road way mode?
View 6 Replies
View Related
Apr 30, 2011
I have cross section data of the existing ground in the form of offset elevation. Can i draw cross sections from the this data? I am using Autocad Civil 3D.
Formate of the data for one section is:
Station 12+000
offset Elevation
-25 350
-20 347
-15 348
-10 346
[code]....
View 9 Replies
View Related
Dec 2, 2013
I am preparing to model a road surface for a waterline project. I would like to be able to generate sections at desired stations showing the sewer, storm drains and joint utility trench along with the proposed water line. My plan is to model the road surface using a surface created from gradings and then create the pipe networks and joint trench.
My question is whether gradings or corridors would be the way to proceed. I have preliminary design data on the road surface which is sure to change.
View 4 Replies
View Related
Aug 22, 2013
How can I restore my object properties dialog box in its default state? I'm recently working on a project when my Autocad Architecture 2013 just stopped working while it was saving. When i re-opened the file, I just noticed that the object properties doesn't show the full parameters of a certain object anymore. The width,height and other parameters in adding a wall is not included in the properties dialog box. Same scenario goes for all the objects, when i click on a dimension line or any line, an incomplete dialog box appears. Solutions that i've tried but nothing worked:
1. Changed User Profle Preferences
2. Changed my .CUIX in the customization file
3. Restart Autocad
4. Reset Autocad
5. Reinstalled Autocad
6. Downloaded and Installed Autocad Architecture 2013 service packs 1&2
I'm Using Autocad Architecture 2013 64 bit and OS windows 8 64 bit.
View 3 Replies
View Related
Apr 4, 2013
Trimble Access, Civil 3d 2012 export road problem
when I export a road file to my TS2 it becomes corrupted (file size 50% of what it should be.
4 months ago there was no problem. The weird thing a is that the other worstation in the office has this issue to.
Here's what I have done to troubleshoot: swapped out both data collectorsexported this rxl file to a virtual instrument on my desktoptalked to cansel and autodesk but the said they haven't seen this problem. I can rule out the following.
trimble/autodesk software, hardware ( to much a coincidence that both work stations have this problem)Data Collectors swapped out - file size of the corrupted rxl were the same on the virtual deskto instrumentcorrupted dwg - exported a road six months ago, now re-exported and the new file is corrupted.
Both machines are identical:
Pentium Zeon
16 gb RAM
Identical software installation
View 3 Replies
View Related
Nov 20, 2013
When i create an intersection, I get error - " One or more of the secondary road profiles cannot be locked at this intersection . What do you want to do ". Both of alignments and profiles is a reference from a data shortcut .
View 1 Replies
View Related
Aug 14, 2012
We have lucky enough to obtain LIDAR for most of our small City as well as ground only points. My problem is that profiles produced using it are rough and jagged (see attached). I've tried contour smoothing to no avail as well as point removal. Perhaps I haven't just tried enough options.
Should mention also I have breaklines along the CL alignment as well as Edge of Pavement.
View 6 Replies
View Related
Apr 9, 2010
how to create a label style for design center of road (simple tangent) in profile that will work between multiple profile views. I've used the 'Create Multiple Views' profile view wizard. I use a horizontal dimension style label for CL road (looks just like an autocad linear dimension). I'd like the label work across separate views i.e. stop at view end, pick back up at view start.
The label I currently use is simply a line component from tangent start dimension to tangent end dimension and the text component is anchored to the line midpoint. Label looks as intended for normal use. For some reason the line drops as if looking for the actual pvi at the right side when i use multiple views.
View 3 Replies
View Related
Jul 9, 2013
I went forward designing intersection profiles with limited survey and simply made an educated guess for the secondary roads pgl tie in point. I have received updated survey and when I move the profile end point to meet existing grade it adds another pvi effectively holding the profile grade I set preliminarily. I'm keeping the lock point. Is there something with the return/ offset profiles preventing this edit? What is the proper work flow?
Civil 3D 2012 & 2013
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram
64 Bit Win7 OS
View 3 Replies
View Related
Apr 16, 2012
I have a storm crossing shown on a road profile, and the ellipse that represents the storm pipe is only showing part of the inner wall (I've attached an image). This pipe is skewed slightly, but the entire pipe crosses the road alignment, and this should not make any difference.
Also, is there any way, yet, (I'm using C3D 2011) to have the label show not only the pipe name, but also the invert where the pipe crosses the road alignment, and remain dynamic,? In other words, without having to edit the label text, and lose the dynamic capability. Land Desktop would do this, but it was not dynamic, of course.
Win 7 64BIT
C3D 2013
View 7 Replies
View Related
Oct 15, 2012
Who knows a software to make the Road Marking & Road Signage automatic?
View 7 Replies
View Related
