AutoCAD Civil 3D :: Network Structure Elevation Change?
Aug 22, 2013
I assume nobody has been able to create a parametric part used for storm pipe networks that can have the pipes attached to a point within the structure other than the insertion, or have the elevation read from a point other than the insertion.
With that in mind, we are trying to develop a tool that would allow us to pick a strucutre, and set its "rim" elevation to a point on a proposed surface that is not at the insertion of the strucure. I am decent with lisp, but have not attempted to gather info from random points on civil ojects.
View 9 Replies
ADVERTISEMENT
Dec 16, 2010
Is there a way to show the MES Top Elevation as blank or a dash? It would be great if I could make an expression but without the use of text strings in the expression editor, I don't know how to accomplish this without using wipe out boxes over the elevations.
View 2 Replies
View Related
Dec 14, 2013
I am working on an existing Pipe Network. I have a location where I have already placed a pipe and filled in the correct parameters for this pipe. But I realize now that there is a concrete headwall near the end of the pipe. So I was trying to insert the structure at the midpoint of a line I have created for OSNAP reasons so it would create the structure at the specified location. The problem is when I move the structure to create at this location, the "Break Pipe Marker" goes away and only shows when I am at a different location along the pipe. So I wanted to see if there was a command or feature to use to tell the software I want to place this structure at a specified location along this one section of pipe.
I wanted to see what my options were. I know I can grab one end of the pipe and move it to the location and then add the structure and pipe from there. But I did this insertion under different circumstances and it broke the pipe into 2 sections while still keeping the same and adding a (1) after it, which is pretty useful when reading printouts and showing that this is actually one pipe instead of 2 pipes.
C3D 2014 SP1
DELL Precision T3600
Intel Xeon E5-1650 @ 3.20GHz
NVIDIA QUADRO 4000 Dual Monitor
32 GB RAM / Win7 Pro 64-bit
View 7 Replies
View Related
Mar 19, 2012
I am using a structure table as a workaroumnd to get a dynamic point tab;e that also shows station offset. It shows Name, N, E, Elev, Sta, OS
I want the elevation shown in the table to be the elevation that was pulled from the specified surface when I set the structures, PLUS 2 inches.
I tried making them all Null Structures, but I am unable to edit the height of the structure - it wants to be 1.467 and won't change.
I am not even sure what i am doing since I don't use pipe stuff all that often.
My machine is hung on the Edit Networks part dialog, which I *think* is where I was trying set the height of a structure.
I tried creating a new structure and it wants half a million parameters for a simple cylinder, even though the ONLY thing I care about is the insertion point and adding 2 inches for the table.
C3D 2012 on 64bit Win 7 all up to date
Dell Precision 7core 8GB RAM
NVIDIA Quadro FX 1800M
LDT/C3D user since release 12
View 2 Replies
View Related
Jan 8, 2013
I have a pipe network created that is shown in multiple drawings. I created labels for the structures showing Rims and Inverts. How to put the Rim info on a different layer than the Invert info? Right now the label has 3 different components...I feel like there has to be a way to put each component on different layers...
View 6 Replies
View Related
Jan 24, 2012
Is there ever a reason the option to add pipes or structures to an existing network would be grayed out? A colleague of mine called a week ago and wanted to add a manhole to the end of a pipe network where he had a clean out.
I didn't see his drawing but over the phone he tells me the button to add pipes and structures was grayed out. It wasn't giving him the option to add both or either or.
View 7 Replies
View Related
May 21, 2013
I need to make a structure label that defines the "PIPE FALL" for each incoming pipe. By "PIPE FALL", I mean the elevation difference between the bottom of the structure and the incoming pipe invert elevation.
Actually, I thought it was going to be pretty simple, just by doing:
PIPE FALL = INCOMING PIPE INVERT ELEVATION - OUTGOING PIPE INVERT ELEVATION <CONNECTED PIPE OPPOSITE STRUCTURE NAME>
or
PIPE FALL = INCOMING PIPE INVERT ELEVATION - SUMP ELEVATION <CONNECTED PIPE OPPOSITE STRUCTURE NAME>
I just need to define the elevation difference between the bottom of the structure and the incoming pipe invert elevation.
View 9 Replies
View Related
Jan 8, 2014
I'm working in Civil 2012 and I'm putting in existing SD. I put in 2 DI's and a MH all on the same network (there is only one in my drawing) and I go to put in pipes and I click to connect to the first DI and then I'm kicked out of the command. What do I do?
View 2 Replies
View Related
Feb 29, 2012
I have 7 manholes in my network, only 3 of them are visibile in the model tab though.
There is structure label on all of the manholes
I can use select similar to mark them and i get "Structure (7)".
I can even see them in the object viewer.
AutoCad 2011 & Civil3D 2011. Product Version 3.
EliteBook 8560w
Intel i7 CPU 2820QM @ 2.3GHz
8 GB RAM
NVIDIA Quadro 1000M
Windows 7 Enterprise 32 Bit
View 4 Replies
View Related
Feb 21, 2012
I have a pipe network, all the structures and pipes are connected properly. When I use the grip to move my structure, it will not move. I have to move both pipes then the manhole to relocate my structure. Shouldn't I be able to move the manhole and the pipes come with it? Instead I am having to make 3 grip edits and then reconnect the structures and pipes.
View 2 Replies
View Related
Feb 5, 2013
The PLS I work under inquired if the pipe and structure tables provided in our construction plans are able to be exported to excel. The only way I know how is to use the reports manage. The problem is, the provided Pipes reports don't contain all the data we are looking for. How do I modify, or create a new, Pipe report? It seems like it should be really easy to export the data to excel..
View 5 Replies
View Related
Jul 30, 2013
Water main pipe network profile labels for structures do not attach to the structure properly in C3D 2014 (this same label style works fine in all previous versions of the software, through the 2013 release). The labels come into the drawing at a northing of 0 rather than attaching to the structure itself. However, if you grip edit and reset the labels, they reset to their correct attachment point. Additionally, if you attempt to grip edit the profile labels with Ortho mode on, it moves the label back to a northing of 0. I've created a new block for the structure, but that does not resolve the issue.
I've included a link to a Chronicle video that demonstrates the label behavior. [URL] .......
View 3 Replies
View Related
Jun 18, 2008
I'm trying to find out what could be the cause of sturcture styles in a Pipe Network Design Drawing resetting to default styles when I Data Shortcut the design into my Sheet? (I.e. I've got gate valves, fh's, and plugs in my design file, but when I data shortcut them into my sheet they are all come in as null structures) Not Cool!
I'm using the same template that contains all the same parts/styles for both design and sheet.
View 9 Replies
View Related
Mar 1, 2013
I have questions in 2012 pipe network labels.
We are having problems with running out of space and would like to squeeze the line spacing between lines to get more room. We know how to do that in standard MTEXT but can't find the equivalent in the label settings.
I have also noticed problems getting dragged pipe labels to stack. I check the box to stack on drag, but it doesn't seem to do it. We created a separate stacked label style.
View 2 Replies
View Related
Mar 6, 2013
I've been using pipe network in Civil 3D for some time now and all I can say is I can't wait for them to rewrite it!
I've had acouple of problems with some of the default parts for the UKIE template which I have managed to fix manually but there is stil one problem I can't seem to solve. For some reason my type E manholes show up in plan and section but don't show at all in object viewer. I've even tried to create a new drawing and place a new network but again the same thing happens.
I've tried going into part builder, validating it and saving it, reload the catalog etc. just incase.
View 3 Replies
View Related
Nov 13, 2012
Civil 3D 2012. One structure in my pipe network is not following along when the network is data-referenced in to other plan drawings. The structure is present in the source drawing, and included in the network, along with the pipes that are connected to it. All other structures and pipes are operating fine.
View 3 Replies
View Related
Dec 10, 2013
I would like to know if it is possible to display the pipe inlet/outlet elevation in my structure label. It seems like it is not possible.It is possible to use the inlet/outlet elevation of the pipe in my pipe label however I would like to display it in my structure.
View 2 Replies
View Related
Aug 3, 2013
I am create the stron network. I want structure profile elevation. How to create expression in structure reference alignment profile elevation.
View 9 Replies
View Related
Mar 5, 2012
So we have to adjust the elevation of hundreds of drainage structures from their existing elevation to the new finished ground elevation.I know we can give this information within the structure label by adding a reference surface but we would like to produce a table with three columns:
Structure No. Existing Rim Elev. Proposed Rim Elev.
How to produce such a table?
View 6 Replies
View Related
Apr 16, 2012
i have some existing drainage pipe and structures in a base plan that i need to change the invert (which is the easy part) and the top elevation to the existing top elevation that does not meet the minimum presect in civil 3d 2012 is there a way to change these min. to match my exisitng elevation for example i have a catch basin invert is 15.45 top is 17.56 with a 18" rcp the cover will be less than 12" and i need to change this.
View 3 Replies
View Related
Aug 30, 2012
I have a pipe network that I am showing in a drainage plan. I want to show the Structure table in paper space. It seems I can only creaate the table in model spcae. I'm ok with that. I made a viewport in my paper space tab to see the table but it keps scaling to full size regardless of what the viewport scale is set to. The table is too big to fit in my drawing. I tried making a smaller viewport but the table keeps scaling to be actuall paper size. How can i get it to stop scaling so I can shrink it to fit on my sheet?
If Civil3D can't do it can I export the tbale to a data linked Spread Sheet then import that (and link it) to my paper space tab so that I can control the size of the table?
View 2 Replies
View Related
Jun 20, 2012
Using Network Layout Tools, can you attach a pipe to a structure in a different Pipe Network? 2013 Civil 3D
View 6 Replies
View Related
Sep 25, 2012
I would like to build an expression that I can use in a label at a structure in a profile view to show the horizontal angle change on the alignment at the structure.
Of course, in the available structure expressions, we do not have the alignment delta angle at that point even though I have a referenced alignment in my pipe network.
Our subdivision code has minimum drop across manhole for different ranges of horizontal angle change.
I want to create a label that shows the minimum drop required at a manhole off it's referenced alignment and I would like to see it on the profile view, because that is where the drop value is relevant.
View 2 Replies
View Related
May 21, 2012
I have about 100 manhole structures with a 0.5' sump. I want them all to 0.0'. Is there a way to change the sump on more than one structure at a time?
The only way I have found to change the sump depth is one at a time through the structure properties.
Civil 3D 2012 SP3 | Win 7 64-bit SP1
Xeon E5-1620 @ 3.60GHz, 16GB Ram | NVidia Quadro 600
View 2 Replies
View Related
Jun 22, 2012
Is there a way to change or create a new scheme (banding) by elevation? For eg. I would like to use only a range of grey no other colors.
View 6 Replies
View Related
Sep 4, 2013
Civil 3D data shortcuts.
So I first created a drawing which included a surface called "CONTOURS" and an existing sewer pipe network. I then created a data shortcut of the existing sewer network and started a new drawing with a proposed sewer pipe network.
When I received better contour data, I created a new "10FT EXIST CONTOURS" surface in the existing sewer drawing and switched the reference surface for the existing sewer structures and pipes to the new "10FT EXIST CONTOURS" surface. And of course I deleted the old "CONTOURS" surface because I no longer needed it.
Now, the part that makes me want to pull all my hair out! When I open the proposed sewer drawing I get all the error messages that "Reference surface 'CONTOURS' not found in reference drawing" for all 22 of the existing sewer structures.
I've tried deleted the existing sewer network in the proposed sewer drawing and recreating the data shortcut but nothing makes the errors go away. Is there any other way the existing sewer structures could be referencing the deleted surface that I have not thought about? How to get the error messages to clear?
View 7 Replies
View Related
Aug 28, 2012
I'm looking to change an elevation of a survey point within a drawing. I can see where it is possible to manually unlock the points from the Survey Database to allow the user to edit the point. I'm not seeing a method or property in the API Help for 2013 to do the unlocking with code.
Also is it possible to convert a Survey Point to a regular Cogo Point through the code? Or do I have to delte the point and then recreate it as a COGO point? I think this will be my work around if the above doesn't work.
View 5 Replies
View Related
Nov 4, 2011
We use C3D 2012 (metric only) - We are attempting to customize our list of structures for Sanitary Sewers. The structure list shows sizes we do not use and we would like to modify them. However, when we try to select the "Inner Diameter" it displays a list of sizes that we can not seem to modify or add to.
I have looked at some of the XML files to try and modify or add new sizes (example: AeccStructConcentricCylinder_Metric.xml) , but they do not seem to be recognized even after I restart the program.
Here is what the file looks like:
<ColumnConstList desc="Inner Structure Diameter" dataType="float" unit="mm" name="SID" id="CCL1" visible="1" context="StructInnerDiameter" index="0">
<Item id="i0">1200.0000</Item>
<Item id="i1">1350.0000</Item>
<Item id="i2">1500.0000</Item>
<Item id="i3">1800.0000</Item>
<Item id="i4">2050.0000</Item>
<Item id="i5">2300.0000</Item>
<Item id="i6">2550.0000</Item>
I tried modifying the last line replacing 2550 with 3600.
I also tried adding a line <Item id="i7">3600.0000</Item>
I saved the XML file and restarted the program with nothing changing that I can see.
Looking for correct file(s) to edit so I can modify the LISTS that come up in the piping modules.
View 2 Replies
View Related
Feb 12, 2008
One good thing about null structures is the way they display in 3D. They cover that gap in the pipe segments. Can I steal that shape?
I am currently using a simple cylinder for water pipe "joints" and turning it off like most people do I think.
View 4 Replies
View Related
Dec 14, 2009
I want to change the reference surface for a pipe network with existing pipes and structures. however the changes will only affect new objects, I have to manually change the others one by one. Even with the vista open I can select multiple structures, but when I click in the reference surface column of one of the selected structures, all the others are deselected.
View 6 Replies
View Related
May 21, 2012
Trying to change the position of the "elevation" labels on the horizontal axis. They come default as being inside the profile and i want them shown on the outside of the profile box.
View 3 Replies
View Related
