AutoCAD 2010 :: SLOW Regen When Viewing From The Right?
Jan 9, 2013
What would cause AutoCAD to choke, ONLY when viewing a model from one direction? In my case, it's the right view, and it doesn't matter how I get to that view, ie "view, right" or "dview,clip". Views from other directions regen almost instantly, but from the right takes a full minute, while Acad tells me up top that it's [not responding].
Issue is only in single dwg. Tried audit, purge, etc. Wondering if there is some obscure (dwg specific) system variable causing this, before trying the WB to get rid of an offensive entity.
View 2 Replies
ADVERTISEMENT
Apr 22, 2010
When switching from layout to model space, and back again, and when switching layouts the regen is slow to an extreme, upwards of (3) minutes. Using Renenall in layout, the regens are quite slow as well. Windows 7, AutoCAD 2011, NVIDIA Quadro FX1800, most current driver.
Additionally, when publishing, the regens are equally slow. LAYOUTREGENCTL setting seems to have no affect.
View 9 Replies
View Related
Jan 22, 2013
I've noticed when I try to hatch something it will regen model every time after I select boundaries.
Below is from command line. How can I turn it off?
Command: BH HATCH
Pick internal point or [Select objects/seTtings]: S
Select objects or [picK internal point/seTtings]:Regenerating model.
Regenerating model.
1 found
View 1 Replies
View Related
May 23, 2012
This happens with a number of drawings, I believe all the files are very large approximately 8mb+. The issue is that by using the REGEN or the Zoom - Dynamic command, it will freeze AutoCAD. I will have to conduct a force shutdown than restart the program.
My question is; where do I start to determine what is the cause? Where do I find an error log?
View 1 Replies
View Related
May 20, 2011
Since upgrading to AutoCAD 2012, everytime I open an xref using xopen, then close the xref, when I go back to the parent drawing the screen is totally blank and I have to regen to get it back. This happens almost 100% of the time in this scenerio. Easy to do a regen, but I am in and out of xref's a lot, and it's getting really old.
View 5 Replies
View Related
May 8, 2012
My layers in layout viewport are displayed in wrong order even after I use REGEN or REGENALL command.
I am working with drawing file with quite big amount of layers (about 100+ including layers of 7 xrefs) and because I want to use different layer settings for each printed drawing I work directly in the layout viewports instead of model space so I don't have to switch on/off countless layers all the time.
The problem is that quite often layers just turn into wrong draw order and don't come back even if I hit REGEN or REGENALL command. To solve this I have to zoom out, jump out of the viewport by doubleklick outside, use REGENALL command and then jump back to viewport so I can keep on working. This is extremely time consuming especially if it happens every 3 minutes, over and over again.
View 2 Replies
View Related
Sep 6, 2013
Not sure of the version of MDT files, but they won't export into Inventor 2011 so they are older than MDT 2009.
I have been trying to figure out why client cannot see objects drawn in MDT when opened in vanilla Acad. I had him check what I believe is the main variable affecting this, proxy show, and it was set to 0. After setting it to 1 and doing a regen, still nothing.
I also checked proxy graphics and proxy notice and they are both set to 1, but neither affect this issue directly.
I've had a few people check this file on their systems and they can see the objects. Various O.S.'s were used to test the file, Win7/64 and 32, however the client who is having problems is using WinXP/32. I am also able to open and see the object on another WinXP system.
Something else to note, I realize this isn't the correct way to use aectoacad, but I tried opening the file in vanilla Acad and used that export to acad command and guess what? The client can see the object now!
I thought export to acad (aka aectoacad) was suppose to be used from what ever application the dwg first originated in?!?! If it works this way then so be it!
View 2 Replies
View Related
Jun 10, 2010
Is there a way to disable the Viewing of DST files in the Recent Documents Pull down so that only DWG files are shown?
View 9 Replies
View Related
May 17, 2012
I've attached an image of my problem for reference. I've had this problem in other versions of CAD so it's likely a user error that I'm not clear on how to fix.
I have several dimensions which I'm trying to place on my drawing through VPMAX in my viewport, but the text keeps showing up upside down. When I manually tell it to rotate 90 degrees, the text remains upside-down but the landing becomes vertical. When I rotate 180 degrees, the text becomes vertical which isn't really useful. Rotating 270 degrees almost solves my problem, but the landing is once again vertical.
If it matters, the UCS coordinates have been rotated 90 degrees for ease of viewing in paper space.
View 2 Replies
View Related
Sep 4, 2010
I tried searching for "Slow scroll" and found one topic about scrolling through layers, but not scrolling through the drawing in general.
Problem: When using the mouse to scroll through a drawing with an attached pdf underlay, the motion suddenly gets really choppy, and slow. The PDF is about 3.5 Mb. Its very annoying knowing that my computer should be able to handle it and then some.
Computer: HP Envy 17 Laptop; i7 740 @ 1.73Ghz; 8gb ram, ATI Mobility Radeon HD 5850 1gb; Windows 7 64x
Failed Solutions: Hardware Accelerator on and off; Played around with performance settings.
View 9 Replies
View Related
Jan 22, 2013
I recently upgraded from ACAD 2004 to ACAD 2012. In ACAD 2004, plotting was extremely quick. In ACAD 2012, plotting seems to be extremely slow. A basic drawing in 2004 plotted as a pdf file using CUTE PDF or PDF Creator would take about 5-10 seconds. In ACAD 2012, a similar file using the same CUTE PDF or PDF Creator will take up to 2-3 minutes. Not a long time but when you are plotting a dwg set that has up to 10 tabs in it, it takes 20-30 minutes just to plot. Is there any way to speed up the plotting in ACAD 2012? I have both ACAD 2004 and ACAD 2012 loaded on the same computer.
View 4 Replies
View Related
Feb 10, 2012
I have a bunch of dwg's that were converted from dgn's using Microstation V8's batrch convert utility. In many of them there are these Mtext objects that, when I hover over them, or when I pick them to change their properties using the properties dialog, slow performance way down. I have to wait about ten seconds for the machine to catch up.
This can get pretty annoying since it ouccurs when I merely cross over the objects when I am not in any command whatsoever.
The text objects are referring to a font that I do not have installed on this machine. I think it defualted to using simplex.shx as a result. I did not get any errors or warnings about the missing shx when I opened the file.
Using Civil 3D on a 64 bit Win 7 Dell POS - everything is up to date.
C3D 2012 on 64bit Win 7 all up to date
Dell Precision 7core 8GB RAM
NVIDIA Quadro FX 1800M
LDT/C3D user since release 12
View 2 Replies
View Related
Nov 18, 2013
I am trying to work out a plan in Autocad and it goes so slowly. The slowest of all actions I do is always drawing a simple line. No other program is running on my laptop.
View 9 Replies
View Related
May 31, 2011
Just installed upgrade to 2012 on same machine as 2011. Within the drawing area of both Model & Paper space, cursor is jumping and slow across screen.
View 5 Replies
View Related
Sep 19, 2012
When I am in ISO view and chose anything other than wireframe, like "Realistic" panning and zooming are very slow. Even a smaller drawing does not act normal. I use a 3rd party software for modeling ductwork and piping, the drawings work fine on our other machine, so it's not the modeling software. It's also not the drawing file, I have tried other drawings that I had no past issues with but it still bogs down.
I have tried the following:
Updated video driver.
Tried different settings under "Options" "Display" and "3D Performance"
Ran AutoCad repair.
Checked and turned off all snap settings and grid.
AutoCad 2011
Intel Core i5 3.60 GHZ
16GB ram
Windows 7 Profesional 64 bit
NVIDIA Quadro FX 1800
View 2 Replies
View Related
Dec 18, 2012
i have big problem to save in Autocad 2011, then we save in 2007 DWG format it takes up to 3-4 min even local this problem exist, reinstalled i computer totally clean, no antivirus just windows 7 and updated,even disabled fidelity. then i save in 2010 format it goes fast.
View 4 Replies
View Related
Aug 4, 2010
What setting would cause a huge, well about 5-second, delay when any entity is selected without a command active and only with the Properties Palette on-screen but autohidden? If command is given first, verb-noun, no hesitation after selecting at Select Objects: prompt. But, selecting any entity first, noun-verb, causes the 5-second delay before the mouse is again active. Very annoying. Closing the Properties Palette completely seems to cure the delay problem, but at a different cost in editing time. The workstation is running WinXP Pro with 4 gigs of ram.
View 9 Replies
View Related
Aug 12, 2013
When I copy and paste on Autocad 2012, it goes very slow.
I installed the service pack, I tried removing the layer filters and a few other fixes that are out there. The machine is powerful enough to handle the application.
I tried reinstalling the application and that didn't do anything. The DWG file that's on the network share is being used by other people without any issue, I'm the only one having this problem.
View 3 Replies
View Related
Dec 6, 2013
i have a test drawing attached with layout 1 and layout 2.
from model to layout 1 takes 2-3 seconds on my crappy computer, from model to layout 2 takes 8-10 seconds on the same crappy computer.
this sample i attached has a xref binded. which result is the same 3 and 8 seconds respectively.
you may think this is not a big deal. but layout 1 will take 10 seconds to to switch to if you have 5 xref while layout 2 will take a minute.
i did my research and haven't find the difference in variables between the two paperspace layouts.
tried all the variables made no difference:
psltscale, msltscale, celtscale, savefidelity, etc.
also set both viewoprts to undefined same thing.
the only difference is "1" is created from a blank autocad template by selecting "metric - no template", and "2" is imported from a civil 3d dwg after done a plan/profile production and that thing created that layout.
is there a tool to compare all variables between 2 layouts and find the differences? i am certain the problem lie within system variables.
Civil 3D 2012
Work: Xeon W3503, 12GB, Quadro 2000, Dell P2211H x 2
Home: 3930k, 12GB, GTX 590, U3011, QX2710
View 9 Replies
View Related
Jun 14, 2012
I import PDFs in Drawings and it takes forever to print. PDFs are only 400KB, so not big files.
View 6 Replies
View Related
May 9, 2012
Autocad 2012 was working fine until a week ago when it started taking a long time to open drawings--even search for drawings on our network. It also takes at least 30 seconds to save files, where it used to take 5 seconds at most.
I found the AutoCad 2012 and AutoCad LT 2012 SP1 Ribbon Hotfix, which sounded like my problem, but it is for Product Version F.107.0.0 and I have Product Version F.51.0.0.
View 5 Replies
View Related
Dec 21, 2009
We are having slow keyboard response while typing in CAD 2010. (It happened a little while using 09 as well). We will start typing a command and our cursor will get ahead of what we're trying to type. Our dynamic input is OFF.
View 3 Replies
View Related
Jul 28, 2011
We recently migrated our fileshare project drawings from Window Server 2003 to Window Server 2008-R2 x64...We are experiencing slowness opening or only right click button on more dwg on XP Pro 32/64bit workstation.
Problem repeats if you try to copy many dwg files from windows explorer, right button properties..i have already disabled "validate digital signatures and display special icons" on each machine .There isn't any slowness problem opening files on other application e.g.. Office.
View 9 Replies
View Related
Sep 19, 2011
We currently have 4 licences for AutoCAD 2012 and once it was installed it takes a really long time to plot and the hour glass just keeps flipping. What can i do to resolve this problem?
View 3 Replies
View Related
Feb 10, 2012
A drawing is almost (20 MB). It is big I don't know why? It works normal in MODEL space. But when I switch to PAPER space, or to save, print, close and open the file, it shows very slow reaction.I made reset to the scale, checking LTScale, deleted all unnecessary objects, purge several times, UCS dynamic off, AUDIT, checking Xref's, texts are type (shx), No layers filters.The drawing has only one layout in few viewports. (isavepercent) to 0.BWhat can I do more to reduce the file size en make it faster?
View 7 Replies
View Related
Jan 30, 2013
I have a delay when switching back and forth between model space viewports,
View 7 Replies
View Related
May 13, 2010
When using the undo command, plotting or switching between drawings in Autocad 2010 and now also 2011 I am experiencing long delays of up to 15-20 seconds at a time which is rather frustrating. I am running a fast spec computer and can't seem to overcome it, I haven't had the problem with 2009 and when need to do something quickly have found myself using the outdated software. Other users in the same office have equal or lesser spec computers and are not having the same issues, I have tried a re-install and this hasn't worked either. I was hoping the new 2011 version would solve this issue but no luck.
View 9 Replies
View Related
Feb 22, 2012
When ever i open a dwg file (it contains Xref files) it's take a long time to open... and i tried the same file to open in Autocad 2007, it's opened with in a second.... and also note that the Autocad 2007 installed in a Dual core pc with 4gb RAM.. and the 2012 is installed in Core i7 12gb ram with NVIDIA graphics card.. and it's 64 bit Windows 7 too.. When i try to open a file it's shows "Loading c:/ ....... base.dwg, etc.. ..
View 8 Replies
View Related
Oct 25, 2011
How do i disable regen and stop autocal lt 2007 regenerating layout and model space when opening drawings. This is a pain when opening and saving large drawings to older versions.
View 6 Replies
View Related
Dec 5, 2011
Attached is a drawing containing a big rectangular lwpolyline and two relatively small lwpolylines near the drawing origin. One of these smaller plines is on a layer that has a dashed linetype associated with it. That layer is also red. When I zoom in on that pline, however, I won't see the dashes unless or until a regen occurs. As of this writing, after trying a few things, I'm almost resigned to including a note telling the client they might have to REGEN in order to see non-continuous linetypes display properly.
View 2 Replies
View Related
Jan 19, 2012
I often need to work on big drawings having utility networks, topographic surveys and properties. Whenever using FIND command in such a drawing AutoCAD regens the drawing. This happens even if FIND command is cancelled and takes 2 to 3 seconds everytime. Can I disable this automatic regen and do only when I need.
View 3 Replies
View Related
