Why there is no infill when there is a hight elevation change? the path is a "building pad", and I'm pretty sure normally it's filled with dirt....Did I do something with the site setting?
View 4 RepliesIve got a problem with creating elevations. When I create an elevation on my floor plan - in this instance level 5 of my 30 storey building I open up the elevation and see the attached view. Its crop region is only 3mm high and therefore only shows me the floor of level 5 instead of the whole elevation of level 5 to the underside of the level 6 slab.
View 5 Replies View RelatedHow We can to change the default height Ceiling plane In Project Browser.
For example, the Default is 2600mm.
I want to Over 2800mm set.
Not in Time Drawing Ceiling.
I'm building a PEMB frame family partly to teach myself and because none of the ones I could find online match the ones I'm working with. It's been a bumpy road but I've gotten the family to the point where there are parameters and elements for the flange, web, baseplate & girts.
Where I've run into a problem are the bracing flanges. The flange at the top of the column was simple enough since it's always horizontal but the beam braces are all 90 deg to the top chord. Any refrence plane or reference line drawn from the intersection of the bottom & column chords to the top chord does not move with the other chords when the family types are changed. I applied a 90 deg angular dimension constraint between the top chord and the bracing flange but when I change the pitch of the top chord by increasing the Ridge Height Revit gives me a warning message that the constraint is no longer satisfied instead of rotating the flange!
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013
Can you change the main header text height in a schedule?
View 2 Replies View RelatedIs there a way to change the elevation of the cut line for an individual stair without changing the cut line for the entire view? The only way I know change the cut line is thru View Properties > View Range > Cut Plane.
View 7 Replies View RelatedI have a wall type that has an embeded sweep for the wall base. My project is set up in two phases, existing and new work. A door has been created in the existing phase, and demoed in the new phase. Where the door has been demolished an infill with the base appears, great! In the new phase I inserted a larger door that cuts the existing walland the entire infiil from the demolished door, but the base still remains. How do I get the new door to cut the base that was created as a result of the infill?
View 1 Replies View Relatedhow to create a wall that infills the gable between two levels of the same roof. There is no internal wall below this location - so this would be some sort of lightweight studwork and panelling rather than brick.
Infrastructure Design Suite Premium 2014
Self-built i7-3930K, 16Gb RAM, P9X79 m/board
SSD(system), HDD(data), Win7Pro64, Quadro K4000
how to apply a filter to a Floor Plan to color code my Walls by Unconnected Height for coordination purposes?
I want to disseminate which walls are currently modeled to deck and which ones stop short so I can selectively coordinate this.
This seems completely logical, but I don't see the option to allow this.
Why does Revit allow me to schedule the Length of a Wall, but not it's Height - am I missing something?
i have some existing drainage pipe and structures in a base plan that i need to change the invert (which is the easy part) and the top elevation to the existing top elevation that does not meet the minimum presect in civil 3d 2012 is there a way to change these min. to match my exisitng elevation for example i have a catch basin invert is 15.45 top is 17.56 with a 18" rcp the cover will be less than 12" and i need to change this.
View 3 Replies View RelatedWhat does the “sample height” indicate for?I couldn't figure out what the “sample height” represent for!
View 2 Replies View RelatedHow to set the “height” of each floor?
I’m wondering how to set the height of each floor in the Revit to adjust the “height” of the wall accordingly?
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
Fiddling around with schedules, I found a workaround to set the row height. Simply:
1 - Add a field which doesnt' contain any data to the schedule;
2 - In the schedule view, select the field's column and in the appearance tab, define a font size to whatever size of rows you would like.
3 - When you now add the schedule to a sheet, you can see that the height of each row is bigger
4 - If you selected to show gridlines, you can define the newly added column in the schedule view to have no borders
And that's my workaround. It's way better than adding spaces and adjusting widths.
With no luck, I have been trying to figure out how to insert a blank value for ceiling heights in a finish schedule. There are other rooms with blank values, however it appears that rooms that once had a ceiling can no longer have a blank value. From the research I've done it seems the only way to correct this may be to delete and recreate the room.
View 3 Replies View RelatedNeed to make a wall with varying height. For example, 3000mm at one end and 4000mm at the other. The result would be a sloped ceiling and roof. Should I make a 'mass' and attach a wall to it or is there a way to vary the height of an existing wall?
View 2 Replies View RelatedSetting the height of the masonry stone,
I couldn’t figure out how the height of the masonry stone can be set.
For example, in the attached screenshot, I wanted the height to be 0.26 meter then how this can be done?
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
Can't seem to adjust the height of a recessed can. I placed the can in a floor plan view in a ceiling and it is sitting on top of the ceiling.
View 2 Replies View RelatedI cant find a way of suppressing the height figured numbers (to replace with GFL and 1FL) . Prefix and suffix do the text ok but for appearance sake (ie client requirement) want to change lots ov spot heights to surpress the numbers. How can I do this - I realise its a system family but usually there are some params - not on this family though?
View 1 Replies View RelatedIs there a way to get the ceiling height automatic in a schedule?
View 4 Replies View RelatedI have got a split level building with hanging light fixtures in a double height room. The cable is connected to the double height ceiling, but the fixture itself hangs right down to below the split level used in another part of the building. I have set the light fixtures level to higher level, reduced the hanging distance right down, tried change the host, but they still hang below the split level line.
The fixture is the Rectangular Hanging Light Fixture from [URL] ... And the drawing is in millimetres.
I am trying to control the height of the camera for a walkthrough so that I can go up stairs. I know that I can activate the "Mini Tour Building Wheel" and can do it that way but it is very clunky to use and I don't always get the right angles. Is there a simple way to control each key frame's heights like you normally would a camera (eye and target elevations)?
View 1 Replies View RelatedWhen I insert a window it sets the window at a SILL height. I would like to default inserting windows at a HEAD height. Can this be done?
View 2 Replies View RelatedWe are creating a parametric family for our window product. We have managed to create maximum constraints for both height and width. However combined with the maximum height and width we have a maximum area alllowance. We are struggling to find a way to build this into our parametric family. How this might be achieved? Is it possible to display warning text boxes within Revit?
View 7 Replies View RelatedWe are looking for a way to document the free height, between two floor slab on two different levels, on our floorplans. We would like to use some sort of tag. And not just text.
View 9 Replies View RelatedI have googled about changing the height of individual tracks and couldn't find much. Is it adjustable? If not, is this planned for the future?
View 1 Replies View RelatedI am trying to change the height of the points. "pntelev layer" all at one time. The drawing was giving to me by our surveyor, and I am having a hard time finding a command to edit multiple points at the same time.
I can select one point and utilize block editor to change the height, but is there a way to select multiple points and edit all of them at one time?
I am using AutoCad 2012 and I believe that is one of my issues, b/c in the past when using Civil3D I had a points tab, and that is where we went to edit things like this.
I attached a .dwg
Is the anyway to keep the body of a custom Elevation tags to stay horizontal as do section tags?
View 7 Replies View RelatedI noticed that I don't have (ELEVATIONS) tab and also (elevation icon). See the picture. Also (Elevation Marks) in the window view are not exist.How can I regain all these?
View 6 Replies View RelatedIs it possible to move an elevation tag in one view and move the same one in another view keeping them in there separate locations?
View 1 Replies View RelatedI am in the process of drawing up an existing building and firstly am setting up with the building mass. I have managed to get the main bodys of the building done and the main roof.The problem now is that when i switch too the east or west elevations to add mass for the roofs on the adjoining wings of the building it wont let me see the model lines when i draw them in the screen i just get an error message " None of the created elements are visible in Elevation: East View. You may want to check the active view, its Parameters, and Visibility settings. "I have my reference line set not far from the building and it seemed fine when i done the roof from the north and south views for the main building. I can see the model lines when i switch too 3D views but i cant create the mass from there.
View 4 Replies View RelatedHow to visually represent depth in an elevation?
The only answer I've found is to use linework, but that can't be the way to go in a program such as revit. That's the whole point of it, right? To not have to sit and do things manually and then have to change the lines every time something in the building changes. I know that Archicad can show line thickness depending on distance from elevation line. And god do i dislike Archicad, but that's exactly what I'm looking for.
Another answer I've found is to use shadows, but then you get the problem of only being able to print as raster = no sharp lines.