I built a basic facade system as a family in Revit 2012, but the materials won't stick. Every time I try to edit the family and assign a material, the material doesn't show up in the Revit file it's loaded into. Then, when I open the family back up to try editing it again, the material that I assigned to it five minutes ago is already reset to default, despite my saving and reloading it several times.
View 1 RepliesI understand how to change material by family type but how can I change object subcategory by family type? Is this possible?
View 5 Replies View RelatedI assigned my students to create lighting fixture family. I wanted them to create a drop-down list of materials within the family to allow a user to select from the list of materials. This is accomplished by using a nested family - the inserted family has the materials defined. The drop-down list appears just fine in the properties, but we aren't able to apply it to the extrusion. I have tried inserting each family type and using the Label parameter, but Revit won't allow the link.
View 5 Replies View RelatedI have created a door family that has a concrete fill that replaces the insulation in an insulated precast wall. When I cut a section through the jambs looking down it looks correct but when the section is looking up the concrete fill pattern is not visible.
I would typically cut my sections looking up so that the exterior face is down in the view as it will be cast.
I am trying to take a custom counter I created as a family and have it show a material in my project. It seems that no matter how I apply the material parameter to the family type object, type or instanced, the material does not change in the project when I apply any new material. I have opened up other countertops I have used from the Revit Default Casework Family and I can't seem to find a difference in the setup between mine and Revit. I wanted to use an instanced parameter so I can change the material per room where the object is used.
View 5 Replies View RelatedI need a file called Curtain Wall Dbl Glass.rfa. It's missing in the Doors folder in my UK Fmaily Library in my software. I've found one on the web. I've copy/pasted it onto my Desktop. How do I now load it into my Revit project ?
View 1 Replies View RelatedI'm trying to align a nested family to a reference line in my host family so that it rotates around a certain point.
I've created the reference line in my host family, locked the end point to two reference planes and then gave an angular parameter to the angle between the ref. line and the ref. plane.
I then inserted the nested family and aligned it to the ref. line. The problem is that when I flex the angle, i get a "Constraints not satisfied" error..
What could be wrong?
I'm using a generic face based family for both host and nested families...
Using Building Design Suite Ultimate 2014
I have recently modified the CC of a part family so that different materials for the same part can be chosen. When I exit the editor and place the component I can see the choice of the materials in the dialog box - no problems (See 1st attachment" But when I go to another users PC they cannot see any of the new materials in the "Place content center" dialog box!?!
For information, we are running Inv. 2011 with Vault Professional 2012
The CC libraries are stored on the server and we have one custom library to which I have publish the modified part family.
The custom CC has been fully synchronised with the Vault server.
The materials.xml containing the new materials used in the part family has been downloaded to the users local workspace.
Inventor 2014 Pro SP1, Vault 2014 Pro SP1
Windows 7, 64-bit
Intel Xeon 3.6GHz
32GB
Nvidia Quadro 4000
This is driving my crazy, I have been using vanishing point to copy a slab of granite onto a counter top to see what it would look like with my kitchen decor.
Everything was going along just fine and I got an island countertop covered using the right plane for it but when i tried to repeat the process for another section of counter I can't get it to work.
I make the grids just where I want them and include the island counter in the grid so I will have a source to copy from.? When I click on the Marquee tool for selecting a section of the source and then click and drag it to where I want it there is nothing in the selection.
I can see the rectangle of the Marquee moving as I drag but when I get to the target area and release it there is nothing there.
I have exactly same question as here: [URL] .... but this solution does not work in 2012 max.
first of all i don't have that "enu" folder with defaults. however i found defaults/designviz.mentalray/medit.mat (designviz.mentalray is scheme that i'm using) but changes to that file doesn't have any effect. after that i've tried to activate designviz.mr scheme again and restart 3dsmax, still no effect.
I can't see my vray light material in the viewport. I've tried shaded materials with map and realistic materials with maps.
View 2 Replies View RelatedIn Revit 2013 I attempt to load an item from the Family but I find that the “Load Family” dialog box does not appear. how to get it to cooperate? Even starting a new project the load family dialog box does not appear. I have done: 1) system restore, 2 ) repaired install, 3 ) re-installed, 4) uninstalled and reinstalled from scratch but still the problems persists on this machine. all other office PC’s with Revit 2013 behave.
View 2 Replies View RelatedI've attached a simple RVT file with a family inserted and the front view active. I need to rotate the family 90 degrees but Revit reports the following error:
"Can't draw because Work Plane is at a very sharp angle in this view. Go to another view or redefine the Work Plane."
I have several window types in my project. Let's say that the window is 3'-0" wide by 4'-8" high - Mark #1. I want to group three of these windows and schedule the group as Mark #2 - not three separate #1 windows. How do I set up the three windows together to become a single window schedulable for the entire opening of the three windows grouped together so that the opening would read 9'-0" wide?
View 6 Replies View RelatedIs there a way to load, for example, a wall created in a different project, into another project?
View 1 Replies View RelatedI downloaded a grab bar family that I thought looked very good. But then I tried to place it on the toilet stall portion (I also downloaded stall partition families). When I tried to place the grab bar, it wouldn't place -- I believe because the grab bar is WALL BASED.
So now the question is how do I go about placing a grab bar (or anything else) that is not wall based so that I can use it with the stall portion? I had tried to use face based but couldn't get that too work.
Im try to crop .rft format but i cant crop my family model in project file. Then how to explode family in project file.
View 9 Replies View RelatedI would like to create family type with drop down list as shown in the image.
How it is created and for what?
Recently, My revit does not load families. The process I use is the following:
In the Build area of the home ribbon, I select the Component button. I going to the Place component ribbon. When I select Load Family form the Mode portion of the ribbon, the properties box pops up. It is locked at this point and I cannot do anything but hit escape. The program functions just fine in all other aspects. I have used a vanilla project to see if the project I am working on is corrupted and I get the same results.
I am trying to create a custom planter based off some line work that I did in my project. It has a curve. basically what I have done is created the line work on plan but now I want to use that curved line to create my family. which I am thinking I can create a profile and then sweep it on those lines. The problem is I can get the line work to the family.
View 2 Replies View RelatedI'm trying to edit the keynote family with no luck. We are updating our standards and getting into using the keynote system in revit. I have added the correct keynote to most of our standard materials and its working great. I then opened the keynote family and changed the justification of the text to justify the way we do notes. I also changed the line style of the leader lines so it matches our other notes.
All went well. I get stuck when I try to change the gap between the leader tail and the text. I can't find anywhere to actually edit the line/arrow in the family that would let me change how that works. If you see my attached image the one on the top is our standard note and the other two are the keynote family.
How to set / change that gap?
I'm trying to create a frame and panel kitchen cabinet door family. It flexes correctly horizontally, but I can't get it to flex vertically. What do I need to correct?
View 2 Replies View RelatedIs it possible to create the Wall family in revit?
View 5 Replies View RelatedRemoving tag leader, I couldn’t know how to remove the leader of the tag from its family. How this might be done?
View 5 Replies View RelatedThis includes door opening/cased and opening-elliptical art. When I put them into my drawing they show up in the preview but do not insert into my drawing.
View 2 Replies View RelatedI know I must just be missing this somewhere, but I would like to shut off the geometry inside a family that's associated with a specific parameter. This is while I'm editing the family.
Specifically, the family I'm creating is for an appliance that has the option of an arched, or rectangular opening. Once I associate the geometry for the arched opening with a parameter, I'd like to shut that off, so that I can create the rectangular opening. Similar to how the family behaves once it's brought into a project.
Right now, I'm just kind of using the temporary hide functionality to shut them off, but if I turn them on, then have to go back to make edits, I have to select the individual geometry all over again to hide it. I've also noticed that some geometry, even when hidden, can still be selected.
As Revit insert a door it cuts the wall starting at the flooring level upward door height but in real building the door openning starts from the top concrete
Can I tell revit to start cutting the wall bellow flooring (leaving the door wing to start from flooring) or how can i add this feature to door family...i would like to control the height of the cut below flooring (e.g be a parametric).
Is it possible to add a rotation control to an annotation family like the ones in elevation tags?
View 2 Replies View RelatedThe line color of my family is not showing up. It is just a symbol and it should be red, but it shows up black. I went to the overides in the project and nothing was overridden, so I went ahead and changed the imported families override to red just to see if it would change and it still didn't change. How do I fix this? When I open the family, the lines are red, just not in the project.
View 1 Replies View RelatedI created one panel family. On plan view, I added two parameter for just width and lenght (Picture 1), but at the same time, I cannot added parameter for adjust the angle in the elevation plan(Picture 2) .
Attachment is my .rfa file
I'm having trouble editing a family I've made. It's a profiled rim for a crate that needs room for a latch. So I need to create a small spacing in the rim so that the latch can fit. I've tried to cut geometry, and edit the family (rim) itself, but I need to edit it in an elevation view and not floor plan.
View 1 Replies View Related