Revit :: Unable To Move Down Wall Foundation
Jan 27, 2012See the attached PDF file.
I can't move down the wall foundation. (The highlighted piece.) What's the reason of it? The properties of the wall foundation doesn't have the offset feature.
ADVERTISEMENT
Revit :: Foundation Not Visible Under Curtain Wall In Project
Feb 26, 2011I am having trouble placing a wall foundation under a curtain wall in my project. Revit says that a foundation has been added but it is not visible in any view. I've tried editing the visiblity properties but that didn't fix the probelm.
View 3 Replies View RelatedRevit :: Creating A Family Component For Wall Foundation?
Aug 12, 2008I would like to create a family component using the wall foundation bearing footing as a template. I cannot find the file where the templates are located. I tried using the structural footing template but it would not give me the same flexibility the wall foundation bearing footing template does.
View 2 Replies View RelatedRevit :: Wall Drawn At Foundation Level - Plan Visibility
Dec 4, 2012I'm having problems seeing the walls I drew at the foundation level in this project. The walls should be shown but I can't get to see them except in a 3d view. Also, when i intended to draw them, I think I should have done it from the foundation level plan but I could not set the plan view to see the above objects in order to draw from them. I drew it from another level and then I modified their base and top constraints afterwards..
I tried to modify the view range of the foundation level without success.
Revit :: Unable To See Curtain Wall?
May 6, 2013I am working in Revit 2013 and built the curtain wall on all four side but i am only able to see it in north and south elevation view and not in east and west elevation view.
View 5 Replies View RelatedRevit :: Unable To Array Curtain Wall Vertically
Feb 20, 2013I'm trying to Array a typical floor for a high rise that I've made a group, but I can't array curtain walls vertically. It's too many floors to do one by one and if I make changes to one floor I'd like them all to change.
View 1 Replies View RelatedRevit :: Unable To Select Curtain Wall Grid Line
Dec 3, 2013Something has happened and now I cannot select grid lines in curtain walls. I can tab to highlight the grid line (dashed blue line) and click once. This used to make the grid line a more solid blue and witness line dimensions appeared. Now the cursor becomes a "move cursor" (four arrows), the grid line highlight disappears and there are no witness lines.
Nothing is pinned. The vertical grid pattern is not fixed. I've restarted Revit and I still can't select a grid line like before.
This problem started when I tried to change a grid line in a curtain wall that I forgot was part of a group. It let me select the grid line and when I changed the witness line dimension value there was an error message with no information except for entity ID and a cancel button. After that I could no longer select grid lines in this project. If I copy and paste a curtain wall from the project to a default (see attached) I cannot select there either. I can still select grid lines in other older projects, however.
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013
Revit :: Isolated Foundation Not Showing As Cut
Feb 4, 2014I am having issues with isolated foundations not showing as cut when the cut plan is through the foundation. The wall foundations are shown cut, but I cannot get the isolated foundations to show cut. I verified by wall sections that both foundation types are definitely passing through the cut plane.
View 9 Replies View RelatedRevit :: Walls Do Not Appear In Foundation View?
May 2, 2013Just what the title says. Walls dont appear when drawing in plan view but appear in the 3d view. how come??
View 1 Replies View RelatedRevit :: Isolated Foundation Not Visible In Plan View
Aug 23, 2011I am already using autocad and Covadis (because I'm road-design, etc. ...-); I'm new building and I use Revit Architecture 2011
Already I do not understand why my isolated foundations are not visible in plan view when the footings are beautiful and well visible in the plan view,...
Revit :: Adding Foundation Slabs To Walls - Everything Unclickable
Nov 6, 2011I'm new to Revit. For instance I was working on adding foundation slabs to my walls .. all walls were done and had slabs beneath them and one wall still didn't have any. Once I tried to add the slab to that particular wall ( just by clicking on it, like ive done with every other wall ) it fails to do so and doesn't add any slab.
But my main problem is, sometimes when I work on my project everything becomes UNCLICKABLE, I do not know what im doing wrong and the only way for me to add walls or anything is by clicking CTRL+Z untill the meny gets highlighted again.
Ive put a screenshot in the folder.
Revit :: Unable To Move Reference Plans While Editing A Family
Jul 11, 2013I'm creating a window family by modifying a pre-existing one. One of the things I need to do is to move the reference planes defining the "left" and "right" edges of the window opening, so as to make to opening wider, but I'm not allowed to do it. The reference planes always move together, so that I'm stuck with a 3'-0" wide opening no matter what I do. I can't find any constraints linking the reference planes to each other or to a 3'-0" dimension - I can't find any constraints on them at all, in fact.
The file in question is attached. As I mentioned, the reference planes I'm concerned about are called "left" and "right". I have been able to move other reference planes in the file.
Revit :: How To Get Wall Sweep Set Up In Type / Structure Properties To Wall Profile Has Changed
Apr 12, 2012Any way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies View RelatedRevit :: Bulkhead Wall Join Skews Bottom Of Existing Wall
Jul 25, 2013I have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
Revit :: How To Align Curtain Wall With Edge Of Concrete Slab / Face Of Wood Framed Wall
Dec 4, 2012I am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies View RelatedRevit :: How To Cut Red Part Of Wall 1 / Hole In Wall 2 By Blue Rectangle
Nov 27, 2011Refer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
Revit :: Changing Length Of A Wall And Wall Type?
Oct 31, 2013When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
Revit :: Arched Hole In Wall And Wall Height
Apr 16, 2013I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
Revit :: Adding Wall Sweeps To Wall Profile?
Jul 29, 2011I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
View 8 Replies View RelatedRevit :: Drag Wall End To Edge Of Wall
Apr 7, 2013“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
AutoCAD Architecture :: Doors Move When Wall Trimmed Or Extended
Mar 6, 2013This just started happening with 2013. The doors are no longer staying put when a wall is extended or trimmed. Somehow they now move relative to exthe endpoint of the wall. Happens with windows and openings as well.
Is there a new default setting I'm not aware of?
AutoCAD Civil 3D :: Cross Section - Wall Move With Lane Transition
May 16, 2012I have an assembly that contains a basic lane tranisition with a retaining wall next to the road. I have created an alignment for the lane transition to follow but the wall stays in the same place. Shouldn't the wall move with the lane transition? The sub assembly are inserted connecting each other. what am I missing?
View 8 Replies View RelatedAutoCAD Architecture :: Unable To Create A Wall
Mar 18, 2013I've been having an issue with autocad architecture 2013. For some reason it won't let me create a wall. I can click it but it doesn't want to actually create anything. It just gives me the selection tool. I downloaded the service pack and still doesn't work.
View 3 Replies View RelatedRevit :: No Wall Gap Line?
Apr 4, 2013Is there anyway no wall gap line between floor when I copy 1st floor walls to 2nd floor. Not to use "Join geometry" & Line work: invisible line" tools? See attached picture.
View 3 Replies View RelatedRevit :: Why Can't See Wall Sconces
Dec 12, 2013Short story is I made a wall sconce from scratch but I can't see the symbolic lines in my ceiling plan in the project.
I needed a linear wall sconce for a client presentation based on one of theirs already installed. The manufacturer doesn't provide BIM for this model so I had make my own. I haven't bothered with photometrics. At this point all I need is a placeholder for the ceiling plan and a 3D model for a hidden line view. I used the wall based light fixture family. There was a plane elevation but no apparent parameter so created one and called it 'mounting height'. After about ten minutes of modeling (and over an hour of tedious aligning, dimensioning and locking of the sketches to keep the model from distorting with changes in wall thickness) I opened the ceiling reference level plan and drew some symbolic lines to represent the fixture on the ceiling plan in my project.
Here's what happened.
The symbolic lines for the CPRL (Ceiling plan in the family editor) are also visible in the FPRL. I don't know why this is and there doesn't appear to be a way to hide them in just one plan. I suspect it's because both are at the same height (the reference level.) I tried changing the working plane before drawing the symbol lines to another plane above the reference level and out of its view range but it had no effect. I can still see them in the floor plan.When I loaded it into the project nothing appeared and I got the message about 'no elements are visible because yada yada'. The symbolic lines didn't show up at all. I checked the detail level and that wasn't it. As far as I can tell the view range for the CPRL and the RCP in my project are the same. They don't show up in the project floor plan either. The sconce is visible in 3D views so it's definitely in there. I tried monkeying with the height of the symbolic lines like I stated in part 1. but it had no effect on there visibility. Symbol lines are visible in other families so it can't be an issue with visibility overides.In my project I noticed there's a parameter for the fixture called 'Elevation'. Changing it moved the fixture up and down on the wall. Changing the 'mounting height' parameter in the project had no effect! This parameter worked fine in the family editor. Playing with the 'Elevation' parameter and the cut plane elevation brought the symbolic lines into view. Apparently the symbolic lines are only visible when the cut line is passing through the sconce. Unfortunately my sconce needs to be mounted at 6 ft and my cut plane is at 7'2 to avoid cutting doors and windows. How do get these symbolic lines to display?
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013
Revit :: Turn Off A Certain Wall?
Jun 8, 2012I want to turn off a metal stud wall but leave visible the pre-cast wall.
View 5 Replies View RelatedRevit :: Getting A Subcategory For Wall
Nov 20, 2006revit should give a sub category for wall so it easy to on and off using visibility and give different line color in the object style
View 2 Replies View RelatedRevit :: Offset Of Exterior Wall
Feb 17, 2013In any event, how do does one use the numerical offset to offset an exterior wall and achieve the new offset wall to be in the correct orientation and location, i.e. exterior brick on the exterior and interior gypsum board on the interior?
View 2 Replies View RelatedRevit :: How To Model Wavy Wall
Oct 24, 2013I need to model a wavy wall in Revit. See attached.
Revit 2014
Revit :: Slope The Bottom Of The Wall?
Dec 21, 2012Is there a way to slope the bottom of the wall. See attached x sec.
View 2 Replies View RelatedRevit :: Can't Create Wall By Face
Mar 26, 2013I am trying to create wall by faces of a Mass I modelled.
This is the Mass: [URL]
Everytime I try to create a wall by face of one exactly face, it accept Location Line: By Finish Face Interior only, when I try to change ANY other Location Line, it gives me a message error.
[URL]
And it is always from the SAME FACE highlighted at the picture.
The mass was made by the floors and top edges. I select all of the edges and create a mass from down to top.
All the other faces are ok and they accept the wall by face and let them change the Location Line except this one.