This is something that used to be very easy to do in autocad (with a polyline) and checking the length on the properties bar. When I select multiple lines (chain of lines) the "length" data is greyed out. I hate having to measure every segment separately!
View 9 RepliesI have a large group of lines that I want to get a total length of. Right now the only way that I know how to do this is to highlight them all and use the list command but then I have to go through the text box and write down each line length and then add them up. This is fine if I have only a few lines but when you get into the hundreds or thousands it becomes a monster task.
I tried copying the text box data into a Word document, removing all of the text except for the line lengths and then dumping that into Excel to calculate. This works ok for a hand full of lines but is not really practical.
I know that there are LSP routines that can do this in the full version of AutoCad but LSP is not supported in AutoCad LT.
Is there a way to automate this process in LT?
Or maybe extracting just the length data from a line to a text file where I can send it to Excel and use Excel to add up the lengths?
I use flat piano hinges on doors for many of the machines we build. I would like to be able to calculate the total length of multiple doors on a single machine. We buy these hinges so it needs to go on a buy out parts list.
So here is my problem:
To make it a useable hinge I build an assembly from two hinge halves.
This allows me to check for interference within the machine when the door gets opened.
I set the BOM structure of the assembly to purchased so it shows up on my buy out list.
Both halves of the hinge are set to normal.
There are hinges of different lengths on the same machine.
I can link a parameter of one of the halves to the assembly to show length of the hinge but I cannot set the BOM base qty on the assembly to that parameter so Inventor can add up the lengths.
When I group the items in a buyout parts list the result is "0." The individual assemblies show the correct length because I use the "length" parameter that is linked for the QTY in the parts list. But I cant "add" the lengths and have a total whe I group them.
I need to have mixed units in this list. Some things are bought as Each and these hinges are bought in length.
I'm in an RFA file and can't seem to draw lines shorter than 1/32" without getting the "Element is Too Small on Screen" error. Even when I zoom in so that 1/32" is equal to the width of my monitor, I still get this error. I'm trying to draw very shallow grooves in a mullion. The attached shortline.jpg file show a line that is long on my screen, but to short for Revit, being drawn. how I can draw very short lines in the Family editor?
View 8 Replies View RelatedI have made a Family that is based off the Metric Structural Framing - Beams and Braces template. When I import my Family into a project and create a instance of the Family (which is a channel) the channel doesn't extend the whole distance of the geometric line. Its always 1500mm long (thats the default length in the .rfa file). See below image for my problem:
I made my extrusion inside the Left Elevation view and not inside a Floor Plan view; simply because it is easier to create the complex geometry of it. Maybe this has affected its inability to stretch to the length of the line? How can I edit my family so that the extrusion will stretch the whole length of the line/beam?
How to determine the length of a multiline. With a polyline if you click on it, it's length is displayed in the properties palette, but that doesn't work for a multiline as no length property shows up in the properties palette.
View 9 Replies View RelatedHow Do I find the total length of several objects or separate lines without having to click on each one individually and add them up.
View 5 Replies View Relatedhow to calculate the total length of walls.... by one command or i just calculate it one by one.....
View 4 Replies View RelatedI use poly lines for wiring, after completing all the routing, i need to calculate the total length of poly line, then wont calculate if line is broken at a point.
View 2 Replies View RelatedI don't know if it's good place to post it but finally there's a plugin in Autodesk exchange to count total length of elements. It names 'Tlen' and I've found it very handy.
View 1 Replies View RelatedIs there any easy way to get the total length of selected lines (even if they are not "connected") ?
View 6 Replies View RelatedI have a plan prepared for CNC steel sheet laser cutting. One factor in the costing of the cutting is determined by cutting time or length of cutting. I want to determine the total length of all the lines in a selection so that I can determine what is the most economical design to achieve my goal. Is this possible in ACAD?
View 2 Replies View RelatedI would like to determine the length, width, and height of a assembly.
Can i use the bounding box method to do this, or the range box?
I use my parts list to generate a total length in inches of the same part that is used in several places in my assemblies. I then export it to excel, convert it to feet, etc. I've been doing this for some time now and it works great. The problem I am now having is I forgot how I got this magic to happen and I need to set another part to appear with it's total length in the list. From what I remember I set the QTY column in the parts list to show the length of the part and then I set the parts list to merge the same parts. For the life of me I can't remember how I did this. How this is done correctly?
All of the parts are created by the frame generator if this matters.
Inventor 2013
Windows 7 Professional 64-bit SP1
HP EliteBook 8470w
Processor: Intel(R) Core(TM) i7-3610QM CPU @ 2.30GHz
Memory: 16 GB
AMD FirePro M2000
3D Connexion SpacePilot
where I can obtain a freeware lisp routine that lists the lengths of all the polylines on a specific layer or within a selection set? I want to avoid list if possible as there are rather a lot of polylines!
View 2 Replies View RelatedI need a lisp file that can read the total length of selected object (lignes, polylines) and summarize them by layers or by color in a table
e.g
command:tl (total length)
select objects
found total length.......
select object (Ent)
total length or [Add/Subtract/Table] :
total length = .......
if table
Enter an option by [ Layer/Color/line Type/line Weight] <layer> :
lisp to count dynamic block including total length.
View 9 Replies View RelatedI have a feeling this goes way back to the first release of INV we had (release 14?). Basically the merged FG member length seems to be calculated using the member centre line instead of real lengths. See the attached Pack-N-Go.
The view on the left is a Merged FG member. The view in the middle is individual FG members based on a line of symmetry in the same sketch. Both are placed using the mid point option in the FG dialogue. The views on the right are the 3 separate members used for the middle view.
The Merged length shows 722 mm whereas adding the 3 member lengths (RH view) equals 740 mm. 18 mm short, or 2 sets of 9 mm (shown in the middle view) which represents the end cuts to the middle member in the RH view.
Windows 7 x64 -64 GB Ram, Intel Xeon E5-1620 @ 3.6 GHz
ATI FirePro V7800 2 GB, 180 GB SSD & 1 TB HDD, Inv R2013 PDS Premium SP2 Update 3 (Build 200), Vault 2013 Workgroup Update 2 (Build 17.2.9.0)
Is it possible to change the length of a line based on the length of an attribute?
I'd like to make the line a MINIMUM length of X" (I haven't decided how long yet--but know I'll need a minimum). But then after the user fills in the attribute, I'd like the length of the line to change to the length of the attribute plus a small amount (again, I haven't decided yet how much extra).
I was wondering if there is a way with DB's to have a line "follow" or "grow" with the content/value length of an attribute. Maybe some method of linking the attribute width to length of the line? Essentially, it would work just like turning on the underline setting when typing in mtext editor (or any program with an underline option for that matter), expect that the line could be placed anywhere, and would not have to reside directly below the text.
View 5 Replies View RelatedWhy revit has two hidden line styles. The first being the system line style "<hidden>" and the other "hidden". You would think you would be able to delete or modify "hidden" to reduce the number of line style a user can select from but you can't.
View 2 Replies View RelatedI have selected several lines (not pl or spl), just lines, all of which are the same layer and such. I want to be able to select all thirty or forty of the lines using either the select similar (lisp, AC2010) or quick select and return a total length of all of the selected lines. In the properties box it shows as varies.
View 2 Replies View RelatedHow can I calculate the total area of material similar to a project.
For example, ceramics, In my project I want to calculate the total area of ceramics, but I do not want a separate display
Instead, I have only one row show the total area of ceramics.
The attached schedule is all good except that I want to get a total for the columns Duplex, Duplex GFI, Fourplex and Simplex. The schedule only shows the (1) column at the moment Duplex Total created as an additional paramter with calculated totals in the project. I am trying to link that to the Duplex column etc...,
Please note that those columns Duplex, Duplex GFI, Fourplex, and Simplex are graphical yes/no paramters for my all in one outlet family created using the annotation symbols separatey loaded in a 3d wall hosted electrical family then turned off and on accordingly.
It's all working nicely expect that the different heights are counting separately, when I want a total of just Duplex's, Simplex's and so forth.
How to determine the distance between the two “flights” of the stair?
I couldn’t find the option through which the distance between the two flights is determined.
Also, how to create another landing at the end of the stair!
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
Any way to add all the areas of a space style to get a total SF#? Is there a way to add this information to a display theme style legend?(preffered) Is there a way to get this information in to a schedule? (less desirable)
View 1 Replies View RelatedWhat's the best way to measure something in GIMP? For example, suppose I want to determine the thickness of a line within an image so that I can extend it? The scales along the top and left sides only give a fairly crude approximation but I want to know exactly how many pixels thick the line is.
How do I do that in GIMP?
I have used color to determine line widths. The plotter set-up recognizes color and assigns the appropriate line width. My new company is determining line width by using polylines. Am I behind the times? Or, is this a better way. Willing to change.
View 4 Replies View RelatedI have been practicing using a older book(copyright 1990) and it has some decent exercises in it. I was able to do this one but it seems I can"t find the proper way to do this..First drawing a line a certain distance..ortho on,click the first point anywhere,move curser to the left and click again. that gives me a line at 180 degrees at what ever length..Line command again starting at the second point of the first line..after clicking that point,I type in @2.38<150 that gives me a line2.38 long at 150 degrees..now how do i make a third line relative to the second line so that the angle is 75 degrees and a certain length..the picture shows what I am trying to draw..using the polar cordinates you get an angle based off the UCS( which is set at world) when you try to draw the third line ..that makes the angle between line 2 an 3 not the angle that I want..To make the drawing,I rotated the ucs -30 degrees..But there has to be a better way than that..
View 9 Replies View RelatedIs there a way to determine the surface area of a staircase? For example when you click on a floor, the properties window automatically tells you the area. Can you do this with stairs? And is it possible to put this information onto a schedule?
View 1 Replies View RelatedIs there a way to determine elements on a workset in a schedule?
View 1 Replies View Related