Part of the design for vinyl siding includes corner trim pieces, it's a standard application. We would like to show that in our models, how to creat a vertical sweep. Is there any way to add a small piece like this in a wall type? It must extend the full height of the wall, and appear only at the corners.
Also, in many of our models, we employ a dutch gable roof style on the front with a wood shingle facade. On the top of the shingles are vertical metal battens spaced evenly from top to bottom. I am wondering/ hoping if there might be a way to add this feature (battens) to a wall type.
In any event, how do does one use the numerical offset to offset an exterior wall and achieve the new offset wall to be in the correct orientation and location, i.e. exterior brick on the exterior and interior gypsum board on the interior?
I am currently modeling a 2-Story Home. I have everything modeled the way I want it, but when I go to the elevations I see a gap where the siding and the sheathing don't touch between floors.
The floors are modeled to the stud to allow sheathing and siding to extend. I knew of this situation beforehand because tutorials on the interwebs say this is the way to combat your problem:
I go into the my exterior wall, select edit type, edit structure, (set preview to section) select siding, and then zoom in on the bottom of the wall in the section preview. The bottom of the siding highlights and a "unlock" toggle appears. I unlock it. I do the same to the sheathing. Then I go to my elevations, cut a section, and zoom in to extend the sheathing and siding.
Side Bar: Why don't the two extend independently? They should.
I am creating a folding door model and would like to use a parameter called EXERIOR WALL OFFSET. I have used this parameter before but am having trouble getting it to work within my family. The only difference is that I created one frame/jamb instead of 4 seperate profiles. The question is, why can't i get the jamb to move within the wall using the exterior wall offset parameter? It seems to move the sash/panels just fine but the jamb is constrainted somehow.
I have the general outline and form of my building designed but I'm having problems with patterned curtain walls.
I have created my own Patterned Curtain wall Family and applied it to a conceptual mass, I have not added any parameters as I'm not too familiar with this aspect of Revit. The corners of the building do not align allowing viewing straight into the interior.
I have attached the model in my dropbox so you can fully understand my problem..
Conceptual Mass - [URL]......
Actual Model - [URL]........
Curtain Wall Family - [URL]......
I am also interested in applying glass to some of the hexagon patterns instead of steel to act as windows. At the moment I'm just turning the transparency up on individual patterns .
I'm trying to learn illustrator cs2 on my own and am having some issues with a few basic functions. I am drawing shapes using the rectangle, ellipses and trying to join them together. How do i trim 2 lines together to make a corner. I would like to cut off the exess at the ends by cutting to the other lines. I know this seems basic but I can't figure it out. In the end I want to make a figure using all the drawing tools ( pen, line, shapes etc) and have the outline just one feature.
I don't know if I am doing something wrong but I made exterior elevations in views for a building and the interior partitions are also displayed. An exterior elevation should only display exterior walls.
I'm trying to draw a wall in plan that has Wood Timbers in the corner. The problem im having is that if i use a Body Modifier it puts dark heavy lines within the wall. And Plan modifiers don't seem to be working. I tried to use an interference condition and that also did not do the trick.
I tried to force a cleanup and that did not work either.
I got trouble connecting my exterior wall to the roof or in other words, it would be good, if the insulating layer would not be pierced by concrete (-:
I created a wall via RECTANGLE/PRESSPULL to a desired height. But I need to be able to increase the height of one corner of the wall. Not quite sure how to do this.
On the attached picture, corner A needs to remain where it is, while corner B needs to be 3' higher.
How to use a 6" concrete curb under exterior walls for California schools? are you using a stacked wall, and if so how do you get the exterior finish to cover up the concrete curb. Or if you are using basic walls stacked upon one another, I seem to have trouble getting my wall joins to look correct in plan.
Any way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
I have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
I am creating a two-storey single-family house. The exterior wall assembly is Core Boundary, 3/8" Stucco (we apply a Stucco material to our Sheathing so in Section we aren't showing a finish material on the exterior), 5 1/2" <By Category> (our studs), Core Boundary, Air Barrier, 1/2" Gypsum Wall Board. We draw the floor system to the face of our studs and extend our walls to the bottom of the floor system, then when we join geometry the floor cuts out the wall leaving only the wall sheathing extending to the face of our floor system.
My problem is when I create a 3D perspective view with the camera my floor system is showing through the walls. It seems to thin out/disappear the larger the perspective view is on the page, but I can only make it so big on C-size page.
Is there a way to hide what Revit shows detailed behind the face of a material?(I tried hiding the floor system in my perspective view but it stills shows the floor outline, I'm assuming because it is being cut out of the assembly).
I am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
Refer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
What would cause lines to move left/right some seemingly random distance in an elevation view? Rarely, I run into an issue where detail lines and filled regions added to an elevation view (not text, or leaders) will move some random distance, I've attached a PDF showing the issue. No other elevations, plans, or sections have anything wrong with them. The model has not moved to a different position.
“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
I need to resolve the corner condition where two boards intersect. I am not able to create a void in order to cut the corner for the geometry. I would like to shape more than one side of the board and make it rounded. How do I edit the different sides of the geometry?
