I'm modeling un hold house and one of the exterior walls have variable thickness.
I don´t need two walls with different thicknesses but just one that is changing is own thickness along his development.
I got trouble connecting my exterior wall to the roof or in other words, it would be good, if the insulating layer would not be pierced by concrete (-:
Picture attached.
How to use a 6" concrete curb under exterior walls for California schools? are you using a stacked wall, and if so how do you get the exterior finish to cover up the concrete curb. Or if you are using basic walls stacked upon one another, I seem to have trouble getting my wall joins to look correct in plan.
View 3 Replies View RelatedI am creating a two-storey single-family house. The exterior wall assembly is Core Boundary, 3/8" Stucco (we apply a Stucco material to our Sheathing so in Section we aren't showing a finish material on the exterior), 5 1/2" <By Category> (our studs), Core Boundary, Air Barrier, 1/2" Gypsum Wall Board. We draw the floor system to the face of our studs and extend our walls to the bottom of the floor system, then when we join geometry the floor cuts out the wall leaving only the wall sheathing extending to the face of our floor system.
My problem is when I create a 3D perspective view with the camera my floor system is showing through the walls. It seems to thin out/disappear the larger the perspective view is on the page, but I can only make it so big on C-size page.
Is there a way to hide what Revit shows detailed behind the face of a material?(I tried hiding the floor system in my perspective view but it stills shows the floor outline, I'm assuming because it is being cut out of the assembly).
I don't know if I am doing something wrong but I made exterior elevations in views for a building and the interior partitions are also displayed. An exterior elevation should only display exterior walls.
View 8 Replies View RelatedWhen I try and change the thickness or move most walls in the project I get multiple room volume warnings that pop up, in some cases 80 odd. These rooms in question can be on the opposite side of the building (60 Meters) and 3 or 4 stories up from the altered wall. So there is no way that all room volumes are overlapping. I've checked all the room volume heights, level placements and that rooms are all bound fine, which they are. I just can't figure it out.
I've figured out a work around but this can be a little time consuming and a little bit fiddly. Ideally I'd like Revit functioning properly and not have to keep reminding my team about the correct way to approach a wall change every time 80 new warnings pop up.
I have heard through the grapevine that this may be a bug that occurs in 2012 due to "internal disputes" we are unable to upgrade to later versions of Revit.
how to create a floor or structural slab that is both sloped AND has a variable thickness?
I can do either, but not both. Thinking that I may need to create a generic mass.
I am using the the tool palette to build exterior walls.. I have the wall as needed finished except for a limestine sill. It is bull nosed and contoured. How do I put the profile in the wall style so it looks correct?
View 8 Replies View RelatedHow can i shell out the part with 2mm thickness walls?
View 1 Replies View RelatedIs there a way to use the coil command to make a spiral out of a rectangle where the thickness of the rectangle starts at one value and ends at another? This would be a spiral torsion spring with decreasing thickness approaching the center.
View 5 Replies View RelatedI want to turn my in-place mass walls (sloped or helical) to structural walls but i don't know how to do it. I'm able to do the walls but when i switch it to the analytical view the wall doesn't appear because it's not structural. It's there a way to do in-place mass structural walls.
View 1 Replies View RelatedWe are using 2011.I created a VBA tool that populates the FX Userparameters with a Thickness Variable..How do I set the Sheet Metal Rules Thickness to the new new FX UserParameter Thickness Variable?
for example:
The Userparamter variable name is "cab_thk"
Under Sheet Metal Defaults | Sheet Metal Rules | Sheet (Tab)
The Thickness entry should read "cab_thk"
In any event, how do does one use the numerical offset to offset an exterior wall and achieve the new offset wall to be in the correct orientation and location, i.e. exterior brick on the exterior and interior gypsum board on the interior?
View 2 Replies View RelatedI am currently modeling a 2-Story Home. I have everything modeled the way I want it, but when I go to the elevations I see a gap where the siding and the sheathing don't touch between floors.
My exterior walls:
Core: 3 1/2" stud + 1/2" SheathingExterior: Air Barrier + 3/4" SidingInterior: 1/2" Gyp BdMy floors: Main:
Core: 3/4" Sub-Floor + 11 7/8" TJI + 1 1/2" Rim-JoistMy Floors: SecondCore: 3/4" Sub-Floor + 11 7/8" TJI
The floors are modeled to the stud to allow sheathing and siding to extend. I knew of this situation beforehand because tutorials on the interwebs say this is the way to combat your problem:
I go into the my exterior wall, select edit type, edit structure, (set preview to section) select siding, and then zoom in on the bottom of the wall in the section preview. The bottom of the siding highlights and a "unlock" toggle appears. I unlock it. I do the same to the sheathing. Then I go to my elevations, cut a section, and zoom in to extend the sheathing and siding.
Side Bar: Why don't the two extend independently? They should.
To the top of wall below.
Part of the design for vinyl siding includes corner trim pieces, it's a standard application. We would like to show that in our models, how to creat a vertical sweep. Is there any way to add a small piece like this in a wall type? It must extend the full height of the wall, and appear only at the corners.
Also, in many of our models, we employ a dutch gable roof style on the front with a wood shingle facade. On the top of the shingles are vertical metal battens spaced evenly from top to bottom. I am wondering/ hoping if there might be a way to add this feature (battens) to a wall type.
I am trying to figure out how to change the color of the exterior of my building, which is brick.
View 2 Replies View RelatedIn assigning a material for a new wall exterior component, I see no other material option other than brick, yet there are many materials sutable.
View 3 Replies View RelatedI am creating a folding door model and would like to use a parameter called EXERIOR WALL OFFSET. I have used this parameter before but am having trouble getting it to work within my family. The only difference is that I created one frame/jamb instead of 4 seperate profiles. The question is, why can't i get the jamb to move within the wall using the exterior wall offset parameter? It seems to move the sash/panels just fine but the jamb is constrainted somehow.
View 1 Replies View RelatedWhat would cause lines to move left/right some seemingly random distance in an elevation view? Rarely, I run into an issue where detail lines and filled regions added to an elevation view (not text, or leaders) will move some random distance, I've attached a PDF showing the issue. No other elevations, plans, or sections have anything wrong with them. The model has not moved to a different position.
View 3 Replies View RelatedI'm trying to use a formula in a family that requires the host wall thickness.
I've setup an instance reporting parameter (dimensioned to the host wall faces) - which works fine in reporting the correct value.
But when I try to use that variable in a formula, I keep getting the error:
"Instance Parameters can't be used in Type Parameter formulas."
Is there a way of getting the reported dimension as a Type rather than an Instance - or is there another work around ?
question...how to make Structural Slab TAG?...
all I can see was structural foundation structural columns and framing
then if i try to make them...i can't find a label or parameter on determining its thickness...T_T
why the side view (Heavy Timber-Side.rfa) represents the thickness of the members rather than the face dimension? For example: A 2x10 (which isn't really heavy timber anyway) is shown 1-1/2" thick rather than 9-1/4" when the side view family is used to draw items.
Wish the family names had been a little more logical (i.e. Heavy Timber-Thickness.rfa and Heavy Timber-Face.rfa)
Seems like these families should at least coordinate with the section view so the top view was thin and the side view was wider.
I'd like to change the line thickness of these structural columns, but changing the view graphics doesn't override.
View 3 Replies View RelatedI have a finished floor plan with 5.5" thick walls, but now i want to make all my walls thicker without changing the size of my rooms. What i can do to achieve this. I tried locking the wall dimensions before changing their thickness but it still shrunk my room sizes.
View 4 Replies View RelatedI'm at my wits end trying to cut a wall with a void. I want to chamfer the corners of a wall, but I can't get even a basic void to cut from a wall. I get the error : "This Mass has no solid geometry for its Void Forms to cut. They must be deleted, or solid geometry added and cut." They clearly intersect, what am I doing wrong?
View 2 Replies View RelatedHow do you tag the rooms that are not fully enclosed by the walls?
View 1 Replies View RelatedWhy Revit 2013 when the walls are installed on some laptops is clearly visible.
View 1 Replies View RelatedThere are certain walls I just can't fillet, what's the reason of it? See attached pict.
View 1 Replies View RelatedI have drawn an existing building thats needs a renovation. In the project i need to add 100mm insulation to the external side of the outer walls. Are there any way that i can add theese 100mm to my existing walls but only show the new 100mm in new construction ?
View 1 Replies View RelatedI am currently doing an MEP project and I am tidying up the model at present. I am having problems attaching the walls to the roofs. There could be a simple solution but I haven't found it yet !
I have tried attaching top base etc. but its not working. I only seem to be able to select one side of the roof when selecting where to attach the walls. I have attached 3d pics showing the walls that are extruding & also one of the walls that I am trying to attach.
Just what the title says. Walls dont appear when drawing in plan view but appear in the 3d view. how come??
View 1 Replies View Related