I've made a few roof hosted families, and they've all been fine in the past. For some reason, with this one, when you load it into a project it appears to be one 'ref level' too high for the roof host, hence revit errors, displaying that it can't cut the roof void.
I assume this is something really simple I should (or not!) have done with the family when I started it, can it be saved?
I'm trying to align a nested family to a reference line in my host family so that it rotates around a certain point.
I've created the reference line in my host family, locked the end point to two reference planes and then gave an angular parameter to the angle between the ref. line and the ref. plane.
I then inserted the nested family and aligned it to the ref. line. The problem is that when I flex the angle, i get a "Constraints not satisfied" error..
What could be wrong?
I'm using a generic face based family for both host and nested families...
Using Building Design Suite Ultimate 2014
I am creating a fireplace family in Revit Architecture 2012 with wall host (Speciality equipment with Wall host). I selected the template created the family, but in mean time i can't understand the wall is having delete option.(i.e it is released from host). I am surprised to see that in the family type, the wall host is missing.
View 1 Replies View RelatedI would like to cut a void into the wall of a host window family. When I place a void in the family, it does not cut thought the wall.
I tried making the void on a plane perpendicular and parallel to the wall plane. I dont know if this has anything to do with how voids work. But its not working. I also dont have an 'opening' element in the window family.
I need to tag my roof soffits, exactly the same way I tag my ceilings to show the height. At present, I have tried to use a ceiling, roof, and multicategory tag to tag a roof soffit and it does not work!!!
Autodesk, how do you tag a roof soffit? send me a roof soffit tag.rfa to start from? The category does not exist in the OOTB family templates.
I am stuck on how to put a gable end on a pitched roof.
View 1 Replies View RelatedHow do get a fascia to suit the make up of the roof, the fascia is to small?Or do i change the roof make up? The make up of my external walls are all the same, but in 3d mode the block work is showing up on some of the walls how do i change this to show a plaster finish?
View 1 Replies View RelatedI need to make a roof on a curved building. But when I try with Roof by Footprint it just brings up the error "Can't make footprint roof."
View 6 Replies View RelatedI am trying to get my drawings into revit but I am stuck on getting the basic form of the building in Revit.
Since I am using slanted walls I need to work with a Mass but I can't get the mass look like my idea. The picture I attached is a simple screen capture of Rhino with the outline of the building.
How to make a dormer or cricket that's inset from edge of roof? The inset (for a chimney) has me stumped. Attached screenshot shows my approach using slope arrows but it's not working with the inset.
View 4 Replies View RelatedI am currently working on a home where i need to have a single slanted roof go across the perimeter of the home to form a roof. But, i have run into the issue of not being able to connect the circled area(see attached) Is it possible to connect those separate roofs and if so how?
View 1 Replies View Relatedis there a way to make a if and conditional statement formula in a family with 3 tests?
For example,
Behind Furniture, Biscuit, Masonry Wall, Hard Ceiling are all yes/no parameters
if(and(Behind Furniture, Biscuit, Hard Ceiling), 0' 0 5/16", if(Behind Furniture, 0' 0 11/64", if(Biscuit, 0' 0 11/64", 0' 0 27/256", if(Masonry Wall, 0' 0 11/64", 0' 0 27/256"))))
what is wrond with my formula?
I am trying to change a dimension based on what yes/no parameters are checked. It keeps telling me that its "a bad if statement format". It works fine for the first teo dimension tests but when I add this last one I get the error. I need the 3rd dimension to check against 3 yes/no parameters all being = yes before moving on to the next check.
How do you get the roof soffit to have the same rafter cut as the roof?
View 1 Replies View Relatedcreat roof with same line on top roof face & roof vertical side face?
View 2 Replies View RelatedOn my Revit project, I need to analise lots of stairs.
But, using the Revit LookUp, when I select one railing, I can`t identify the stair that is the host of this railing.
Or, on the other way, when I select one stair, I can`t identify the railings that are connected with that stair.
What can I do to recognize these on my code?
How to configure the schedule synchronization between Host and Accelerator of Revit Server 2013
View 2 Replies View RelatedI am putting an internal screen family together.
As the wall wraps do not work on the soffit (only on reveals), I have used a sweep to match the wall plaster thickness to provide a finish.
Is it possible to report the host wall finish material and have it assigned to this sweep automatically ? I have tried to add a finish layer to the host wall in the family - but have not been able to find a way of extracting the material value for this layer.
For the moment I have left it as an Instance property for manual correction - but automated would be great.
I'm trying to use a formula in a family that requires the host wall thickness.
I've setup an instance reporting parameter (dimensioned to the host wall faces) - which works fine in reporting the correct value.
But when I try to use that variable in a formula, I keep getting the error:
"Instance Parameters can't be used in Type Parameter formulas."
Is there a way of getting the reported dimension as a Type rather than an Instance - or is there another work around ?
I have made an extruded wall and when I attempt to add a window I get this warning.
None of the created elements are visible in Structural Plan: Erdgeschoss View. You may want to check the active view, its Parameters, and Visibility settings, as well as any Plan Regions and their settings.
I have a staircase from the first floor to second floor with a total of 3 landings.. I need to fix the railing at the bottom to go down to 3'0, right now its sitting at 3' - 6"... AT 3'0" it needs to connect to the handrail that wraps around (the red)...normally I can just edit the railing by pulling it longer but since it was a place on host railing.. it looks like it loops around and when I tried playing around with that to extend the bottom rail.. it gave me an error..
View 1 Replies View RelatedWhat kind of an instance paramater needs to be implemented in order to account the host wall type in the door schedule?
View 2 Replies View RelatedI have two roofs that I am trying to join. It consists of two Gables. The eaves and type of cuts are the same, but it still says they can't be joined. Attached is an example of what is happening. The shown highlighted image is actually what I am trying to achieve.
View 4 Replies View RelatedHow do you add a soffit to a roof?
View 2 Replies View RelatedI have an existing roof with a new dormer.NEW dormer is created in a view with phase filter set to Show Existing+New Shouldn't the roof opening be shown as demo in the demo view??
When the opening is selected, the properties show the Phase Created=Existing and it is grayed out and not able to change to New Construction.
I'm using Revit Arch LT 2013. I do not need to know what Revit can and cannot do.
I am currently doing an MEP project and I am tidying up the model at present. I am having problems attaching the walls to the roofs. There could be a simple solution but I haven't found it yet !
I have tried attaching top base etc. but its not working. I only seem to be able to select one side of the roof when selecting where to attach the walls. I have attached 3d pics showing the walls that are extruding & also one of the walls that I am trying to attach.
I have included a picture of the roof I am working on. As you can see I have 2 different roofs set up here, which doesnt look very good. I was wondering if there is a way to create one roof with 2 different slopes like I have here? I would like it to start out at a 3/12 slope for the first 4 feet and then switch to a 6/12 for the rest of the roof. I have not been able to figure out how to get this to work.
View 2 Replies View RelatedI'm trying to create a simple shed roof attached to the sloping walls of a rectangular building. 4 walls, south wall 10' h, north wall 11" h, and the east/west walls joining them are therefore sloped.
I want to attach a simple shed roof to the top. Here's how I think I should do it:
1. create a new workplane aligned with the top of the walls.
2. switch to that workplane.
3. use "Roof" - Extrude" option to create the roof.
Assuming I'm correct in my steps above, I should be able to create the roof.
QUestion - How do I CREATE a new workplane where there is no object already to choose? Program won't let me create a workplane in workplane viewer by picking the tops of the four walls (in any of the tiled views). What am I missing?
I'm working on a blueprint and trying to get my roof to do something besides a straight slope, but it isn't going well. I need the roof to curve from the corners inward to the point, like the top of a Japanese pagoda.
View 1 Replies View RelatedI am trying to edit a roof assembly. My top layer is a roofing membrane. I give the roofing membrane a thickness and try to save and I get an error message saying that it needs to be 0" thickness. I set the thickness to 0" and I get an error message saying that it needs a thickness. How do I get pass this Catch 22?
View 5 Replies View RelatedI have this house Im trying to make on Revive and I can't get the roof to join together at all. I've had this problem for awhile now and I can't seem to get past it.
View 7 Replies View RelatedDetermine the roof pitch, then it has the typical triangle with 1/2 pitch and 1/4, 1/3, 1/6 and so on. I know rise over run like 5/12, but don't understand the fractions. How do I get 4/12 or 5/12 and so on from the fractions?
View 4 Replies View Related