i'm using a canon BJC-210 SP bubble jet printer. i try to print a colored image. the output wasn't the same as the original image. try to fix it in the printer prerferences but to no avail. the image is in jpg. format at 100% resolution.
View 7 RepliesI've been asked to do a poster A2 size 594mm x 420mm 300dpi but when i enter these dimensions my pc is slowing down dramatically. whats the best way to achieve better performance?
View 7 Replies View RelatedColor Management while Printing has been one of the challenging areas which has been discussed a lot over user forums and has been a painful area in terms of clear understanding while taking print outputs.Here is an easy-to-understand KB (Knowledge Base) article ‘Color management settings for the best print output’ to get the best from your printers using PSE and bridge that knowledge gap.
This article explains color management in Photoshop Elements, how to get better prints, and addresses some of the following issues like horizontal / vertical streaks in print output, too dark or too light print output, ICC profile problems and Color differences between prints from PSE and other applications.
I was using CarelDraw 12 and had an output problen when I purchased a new printer (HP Laserjet 1525) The page is set for portrait, 8 1/2 x 11, as it always has been, the printer prints the top half OK, but shoves the bottom half of the document up so that the final copy printed is 8 1/2 x 8 1/2? I have downloaded a trial version of X5 and it does the same thing so I am assuming it is a printer/driver issue?
View 2 Replies View RelatedEvery time i print pdf or print to the printer machine, the output is black color no matter what object i print.
View 3 Replies View RelatedI am creating colage images in Photoshop CS4. I sometimes use scanned vintage daguerreotypes or other small snapshots. They are often small sized at 3.5" x 4.5" or 4.25" x 5.5". My Epson 835 scanner can scan in at 300, 400, up to 800 dpi. If I intend to print these scans at 8x10, 11x14 or a larger size within the overall collage, should I scan in at the highest dpi allowed by my scanner? Does this make a real difference after 300 in resolution/clarity?
Also, Does Photoshop CS4, in the enlarging process, as I bring the smaller image into my composite and stretch size it up with (T) tool, end up just making "junk pixels" using "Bicubic" or "Bicubic smoother" in the printing from flattened PS file, even tho I scanned in at a high dpi? scan in at best dpi so that the image won't be pixelated, lose resolution as it is used larger inside the final composite collage.
I have a problem with the file name of my pdf, after i publish drawings with DWG To PDF.pc3...I used to be: "the file name of dwg drawing"
+
" - "
+
"the name of the sheet"
--> in my case:
V10.350-05 + - + A4
--> V10.350-05-A4.pdf
But now it becomes always V10_350-05-A4.pdf...how i get the underscore back to a point?
The prepping process should be really simple right? Separate colour layers, using Illustrator, then print each layer onto transparency sheets. Well I'm about to loose my mind.
The image is CMYK, its a single spot colour (I think) which is red and the outlines are black. Printer is a Canon ix6500.
I can't seem to separate the colours in Illustrator CS3?! Why?! When selecting Print > Output > Mode > it won't allow me to select Colour Separations.
I've tried to overcome this by selecting Printer > Adobe Postscript and PPD > Canon ix6500 series. This allows me to select Colour Separations, but then it won't print, it only saves it as a PDF, and prints it as is.
if the print module sends srgb data to the printer by default?
The reason is I use a rip (it controls the printing) and the input needs to be matched so srgb > srgb this is the setting I have at the moment, but then someone meantion it was prophoto rgb which has me thinking?
I have created a bunch of Page Setups (for both Paper and PDF) that work great when plotting from the plot menu. Lately, I've convinced my people to start using the sheet set manager and the publish command. However, on some computers, (not mine) plotting (to PDF) from the Publish dialog box outputs a file that seems to ignore the page setup. Using the very same Page Setup, the file comes out perfectly when plotting from the regular Plot menu. I don't understand how:
1- I get the same result with both methods on my computer (the one used to create all those page setups);
2- I get page setup to apply perfectly on my computer;
3- I get the expected result on the problematic computers when using Plot;
4- But I get different results on the problematic computer when using Publish.
*Note: In the publish dialog box, I use "Publish to: Plotter named in page setup" and then I select the wanted page setup for all my selected layouts in the list. My page setups are using "DWG to PDF.pc3", so the "plotter named in page setup" in all cases should be "DWG to PDF".
I've been doing tests with PDF files set on A1 format (841mmX594mm) and the output is perfect on my computer. Then on another computer, strangely, I get a PDF with these dimensions: 863.6mmX558.8mm (34"x22"). On the second computer, doing the very same steps, I get 431.8mmX279.4mm (17"x11"). Three computers, three different outputs with three different values. One works, two miss. I'm stoked.
Keep in mind that all three computers output perfect files when using the standard plotting menu (using the same page setups) so I doubt the page setups are incorrect. Does the Publish command deal differently with page setups than the plot command ? I would have assumed that both commands would react the same. I 'd like my team to be able to batch plot like I can on my computer.
Our local agency has come up with a requirement that CAD-generated drawings be submitted to them as 200 dpi TIF files, of between 300kb and 900kb. They do not accept dwg, dwf, or even pdf.
When we create a new plotter in AutoCAD, using any of the raster file formats, setup for the format only allows 100dpi. You can create larger numbers of pixels, 1024x768 vs 1600x1200, for example, but that is not translating into higher resolution.
We have tried the route of printing to pdf, then converting to TIF, but the file sizes are coming out far too large.
If we are unable to find a solution, I guess we can always print to hardcopy and then scan to tif. In 1996 I would have been happy to do that, but not now.
Our specific version of AutoCAD is AutoCAD Civil 3D 2013, but I am sure this is more a generic AutoCAD issue.
I'm having problems with printing a color seperation. I'm working with CS5 and it won't allow me to print seperations to a pdf-file. I tried to print to an Adobe PostScript file, but also this won't allow me to select the Separations (Host-Based) or In‑RIP Separations Mode as that option is greyed out.
I followed: [URL]
I made sure all colours are in cmyk and already unsuccessfully checked google for solutions, but i'm sure that i'm just missing a simple option.
Using an HP 1050c Plus with the latest HP drivers for Windows XP on AutoCAD MEP 2009. If I use the standard printer margins it all works fine, except that the margins are way too big and no border we have will print without cutting off at least .25" all around. If I go to properties and change the margins to .1" all around, my 42x30 sheets will print out with 43" of paper. If I make them .25", I will get 42.5" of paper. I just started at this company and have never had this problem before with an HP 1050 plotter. I have tried different combinations of the Extend margins, Inked area and autorotate checkboxes but haven't been able to figure it out yet.
View 2 Replies View RelatedIn LR4 print module the print and print one tabs are greyed out and I can't reset.
View 1 Replies View RelatedSo I am working on this document and it has silver background. I go to print preview (Photoshop cs3 and cs4 on Vista) and I get color looking more like bronze looking but when I do print, it comes out just like it should (in working mode which is Monitor RGB with Proof colors checked).
This setting is the only one I've used to make sure image/psd looks exactly like what it should when printing. I tried the default Working CMYK with and without Proof colors but it's still showing me the bronze look instead of silver. I've looked on the net and no exact easy fix for this was found. I really really appreciate any help.
Another simple question is regarding size. I'm working on a document size of 17.5 x 8.7 inches and the actual Banners will be printed at size 175 x 87 inches (5 banners each at 35inch wide but combined into a big one). So essentially, I'm working at 10% the size of what the final print will be and my file size is 760mgs. You can only imagine how big the file would be if I work on the actual size.
When printing from PS CC using the print dialogue box I am getting a severe red shift in the final print. When I print the same image from PS CS5 or CS6 I get a color-correct print.
I am running a MacPro with OS 10.7.5, and printing to a Canon iPF8300 with its latest firmware and print driver. I am using the proper ICC profile for the paper. In the print dialogue box, I select "Photoshop Manages Colors".
A couple things I noticed: In the "Print Settings" where I dial in the printer setup, the settings for "Color" are both turned off (Colorsync & Vendor).In the printer driver settings (still within "Print Settings") the "Color" tab is grayed out, but when I click the "Settings" for that sub-panel, Colorsync is selected.When I printed the image from the Canon PS Plug-in, the red cast was gone, but the blacks were too heavy (there is no "Black Point Compensation" check box available because the Canon plug-in uses Adobe Color Engine for that, and it's only 32-bit and won't run).
-PC based system running Windows Home Premium 64 bit8 GB ramLots of hdd spaceCS5.5 Master Suite
-Epson Sylus Photo R1900
Operating system, CS5 suite and printer drivers all updated.
When attempting to print a photo, it can take anywhere from 5 to 15 minutes for the print dialog box to open up. It takes SO LONG that it appears that Photoshop has frozen, but it has not. The print dialog box opens eventually. This started about 2 months ago. I have looked at all preferences, assigned more RAM to Photoshop, uninstalled and reinstalled the entire suite, ran all updates, uninstalled and reinstalled the printer drivers - all to no avail.
I am at a loss as to why it would take SO LONG for the print dialog box to open after selecting print? I thought there may be a problem with the print spooler or print queue, but the slowness happens BEFORE the print back system is touched. The print queue is empty, and there is nothing stuck in there. I've checked.
I'm having trouble printing in Photoshop CS2. Rregardless of which printer I try to print to, I get the message "Could not print because of a problem writing the print file". I have never encountered this error before.
The psd file I am printing is a wall banner, and is quite large (~200MB). It contains elements copied/pasted as pixels from Illustrator CS2. However even if I flatten the file, or save as a flattened tif, I still get the same error message.
Thinking that the psd file is corrupted, I tried printing an earlier version of the file, with no luck. I've even tried printing other, small unrelated files, and can't print those either. Even after rebooting the computer.
The computer I'm using has a dual core processor, 4GB RAM, a decent graphics card and is running under XP. I have gob-loads of HD space and also use a scratch disk.
I really only want to print the file myself as a proof. However, I'm concerned that the banner printers won't be able to print the file either.
I have Windows 8 and am new to Elements 11. How do I get print to completely fill a 4 x 6 print paper?
View 5 Replies View RelatedI have trial version of Elements 11; Also have full version, but have not installed yet, as I wanted to wait until I completed current project. I created/edited an album of wedding photos in the Organizer. I tried to upload album to Shutterfly to make an archival DVD and also make a photo book in Shutterfly. The photos uploaded individually to the Shutterfly print page to print individually, but the album will not upload to My Pictures, it shows the album name, but it is empty. How do I get the photos to upload?? Shutterfly was not sure how.
View 1 Replies View RelatedUsing a Mac, what is the best way to print multiple images on a 4 x 6 print in Photoshop Elements 11?
View 5 Replies View RelatedI've some problems with Adobe Brigde, it's the first time using that an I wanna export some photos but I don't have the tool Output or extract (I don't know the excatlly name in English, I'm working with the french version).
I tried with Ctrl+K ->bootscript but I cannot find the Output took inside.
Another problem with Adobe Extention Manager CC, it's impossible to install new extention, I rode the tutorial but it doesn't work, I want to install some brush for exemple.
What settings do I have wrong that I see certain colours in PS, then either 'Save as', a jpg (for web use).. Or even 'Save for web'..
And when I compared the colours to PS, they are different?
Usually more red/magenta in jpg format.
I have been told my a printhouse that my designs in photoshop need to be submitted as vectors and saved as an .eps file. So I saved my psd design as an eps file but they said that it wasn't correct.
I have since been informed by them that I need to my pixel graphics into curves, even the text. They suggested that CorelTrace would be able to trace my design with curves. Is there any way that this can be done in CS2? The design is quite simple, a few stripes and some text.
So anyways im runing the New Photoshop. i was working on an image a while ago and bla bla.. I go to save as .jpg and for some reason the photo comes out Much more contrasted then it actualy looks like in photoshop.
like wayyy too much, like its geting kind of anoying because its not the picture i made it to be. it used to work fine before. what should i do.
could i get a broadcast video output in Photoshop CS4.I would to check colors on a PAL monitor,
View 1 Replies View Relatedway i can get photoshop to put out xml and icon files along with my psd files? I want to make my own photo lithos but can figure out how to out put it.
View 1 Replies View RelatedI have a sliced image, which i'm trying to "save for web" using JPG format for all slices, but when i select the JPG settings (these in right) it outputs as a JPG only one of the slices, and everything else is GIF?! If i select all slices one by one and set them to save as JPG, it will work, but that's just too much slices, and i think there should be better way?
View 4 Replies View RelatedI use CS6 on a Mac pro os 10.8.3 & print to an Epson Pro 4900. If I print an image via LR4 print module the print comes out at 12 X18 in. Recently I have tried that same image via CS6 and the print comes out at 6 5/8 X 8 1/2 in.
In Print Settings in Printer Setup in the print module of CS6 stats "Super A3 / B 13 X 19 but the printed image dimensions are a little over half of that.The printer used to print normally in CS6 print file.
I've been using Photoshop CS3 for awhile and printing fine. I just updated my print driver (Epson 3800 to version 6.5) as well as my graphics driver (NVIDIA GeForce 8500 GT)at the same time. After rebooting I cannot click on the Print menu selection to print. IE: When I click on Menu the Print option is greyed and not selectable. Print as well as Page Setup, and Print One Copy are all greyed out (not selectable). I rolled back my graphic driver and rebooted and it still doesn't work. I then upgraded my driver again and it doesn't work. I've opened jpg's as well as psd files and no matter what file I open the Print menu's are greyed out. I can print from Word and other programs. I also reset my preferences (con-alt-shift) and still can't select print. I've done everything but uninstall. I'm hoping not to do that. My computer is on: Vista Ultimate 32 bit SP1, 4gb ram. In addition to updating the print driver and graphics driver I updated: Ultimate Extra Sounds, Group Policy Preference Client Side Extensions, Samsung CLP-310 Printer driver, and Microsoft Tinker.
View 4 Replies View RelatedI'm editing a storyboard with music in the timeline panel. I work in a studio and don't want to disturb everyone by repeating the same part of a track over and over while I work. So, I plug my headphones in BUT...sound keeps coming out of my display (even though I can hear the audio up/down "blip blip" in my headphones when I adjust volume). Searched preferences but there is NO mention of any way to edit the audio output.
View 4 Replies View Related