CorelCAD :: Can't Do 3D Pattern Counter Clockwise With Angle Less Than 360 Degrees
Apr 5, 2013
When using 3D pattern, and specifying a negative angle for counter clockwise, with an angle less than 360 degrees ( eg, 90 degrees ) the pattern will be spread over 360 degrees anyway.
Also, the directions in the application are wrong. negative angles are for counterclockwise, not clockwise.
Workaround: Make all patterns clockwise, and reverse the direction of the axis around which it rotates. This will achieve the desired outcome.
View 9 Replies
ADVERTISEMENT
Apr 9, 2013
I have this
Matrix3d cur = ed.CurrentUserCoordinateSystem;
Vector3d x = new Vector3d(1, 0, 0);
Vector3d y = new Vector3d(0, 1, 0);
Point3d o = new Point3d(0, 0, 0);
[Code] .....
Code is rotating well my model, but it's zooming to bad point. I want to zoom to the point from previous view, so I'm transforming it by new UCS - unfortunately something is going wrong (it's not this point what I want).
View 1 Replies
View Related
Mar 23, 2010
How can i test a polyline if its clockwise or counterclockwise? I have a routine that gets the area of polylines then if clockwise,the area is positive and negative if not. But I dont want to get the area just to test if its clockwise or not.
View 9 Replies
View Related
Nov 29, 2013
I have some closed polyline in a rectangular area like below screen shot. I want numbering these polylines counter clockwise or clockwise by selecting a reference polyline. In the below screen shot , I have highlighted a polyline (red marked). So , first I select that polyline and ask to numbering other polylines in couter clockwise.
The result of my requirement should be like below screen shot. how to do that? sample code in VB
View 9 Replies
View Related
Jul 28, 2013
Deriving “counter clockwise” azimuth from “clockwise,I’m wondering if there is a technique to automatically derive the counter clockwise azimuth from the clockwise or vice versa.
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
View 6 Replies
View Related
Sep 7, 2013
I am trying to set up the bulge for a polyline, in order to set up the bulge currecty I need to know if the polyline was created clockwise or counterclockwise.
View 4 Replies
View Related
Jan 10, 2006
I'm using the liquify tool to fit a fake tattoo to a face, and I want to twist part of the tattoo to adjust for perspective. Unfortunately, the twirl tool in liquify is in fact a "Twirl Clockwise" tool- Counter Clockwise doesn't seem to be an option!
View 5 Replies
View Related
Oct 15, 2008
Im drawing in isometric view and want to change the default drawing angle from 30 degrees to another angle.
View 9 Replies
View Related
Sep 7, 2011
Is it possible to rotate a viewport to an angle other than 90 degrees. I am trying to rotate a viewport 11 degrees counter clockwise. I cannot rotate the model.
View 1 Replies
View Related
Nov 9, 2011
I am currently using 2010 version of AutoCAD and I am having difficulties sorting out my angles.
I need to make a line of 25 at an angle of 150 degrees. Upon doing this it always goes the wrong direction to which I want the line to be facing.
View 9 Replies
View Related
Oct 20, 2011
Is there any way possible to have an angular dimension to denote an angle of greater than 180 degrees?
View 4 Replies
View Related
Aug 15, 2011
good way to start a line at one of the 45 degree angles of a circle block?
View 9 Replies
View Related
Jan 9, 2014
The rectangle tool is drawing at 90 degrees. I tried to fix it with the preferences>general>constrain angle, but I see that is ALREADY set to 0 degrees, yet the rectangle is 90 degrees! Is there another setting I should be aware of?
View 25 Replies
View Related
Mar 2, 2012
Almost every time I add a linear gradient to an object I want to change the angle from 0 to 90 degrees.
Is there a script that I could use for this, so that I could assign a keyboard shortcut and press that instead of clicking the box & typing 90 all the time? (i.e. select an object, run a script & it would apply the standard black to white linear gradient at 90 degrees instead of 0.)
View 5 Replies
View Related
Jan 16, 2013
I would like to know how to draw segment elbow 90 degrees ( segments are not equal ) and create Flat Pattern for each of the segments - using sheetmetal in Autodesk Inventor?
View 9 Replies
View Related
Oct 27, 2009
I have been practicing using a older book(copyright 1990) and it has some decent exercises in it. I was able to do this one but it seems I can"t find the proper way to do this..First drawing a line a certain distance..ortho on,click the first point anywhere,move curser to the left and click again. that gives me a line at 180 degrees at what ever length..Line command again starting at the second point of the first line..after clicking that point,I type in @2.38<150 that gives me a line2.38 long at 150 degrees..now how do i make a third line relative to the second line so that the angle is 75 degrees and a certain length..the picture shows what I am trying to draw..using the polar cordinates you get an angle based off the UCS( which is set at world) when you try to draw the third line ..that makes the angle between line 2 an 3 not the angle that I want..To make the drawing,I rotated the ucs -30 degrees..But there has to be a better way than that..
View 9 Replies
View Related
May 18, 2012
How do I get the export parcel ananlysis to show degrees minutes and seconds instead of the default decimal degreees. My direction settings are set to DMS, but I can't see where to change arc deltas...
(running C3D 2012 sp4, Win7 64bit, 8GB)
View 1 Replies
View Related
Oct 13, 2013
I am setting up a family of parts that consist of a round disc with a fixed OD and a circular pattern of notches cut into the OD. The notches must go to a certain depth from the center, so those parameters are set. My problem is that I need to control the amount of material left between the notches, along the OD, after the pattern is done. Given the fixed parameters of the major OD, minor OD (3.5" in this case) and number of notches, the only way to control the amount of material between notches is to change the angle. When I set up the sketch to do the notches, I can only get a fully constrained sketch if I assign a specific angle to the notch. I need to be able to set it up so that the angle of the notch varies so the end result is a specifc amount of material left after the circular patter is completed.
In the attached PDF, I show what I have done so far. In this case the OD of the part is 4" and the diameter of the notch at it's closest to the center is 3.5". So basically, I end up with a driven parameter of 0.443. If I assign this value the parameter of d14, I need to make it equal to a ratio of another parameter (let's call it d15) so that d14 = d15*2.. This can only be accomplished by changing the angle.
In my family, the major OD and minor OD remain the same, but the angle must change to retain a specific amount of material between the notches when the number of notches is increased or decreased.
Is there an iLogic rule I can write to control this?
View 6 Replies
View Related
Sep 5, 2012
When I open any image, photoshop rotates the image 90 clockwise by itself. All the other programs (even windows imageview) dont do that. Only photoshop does that. I can open the photo in any other application and they are fine, but when I open them in Photoshop CS5, they get rotated.
View 7 Replies
View Related
Jul 13, 2013
I have an avatar which is positioned correctly in PS & in Preview. When I insert that in my Avatar on this forum, it is rotated 90 deg clockwise! ? When I rotate it in PS and load as an avatar, it appears the way it is rotated. ? Very perplexing.
View 4 Replies
View Related
Nov 19, 2012
I have an image, and I want to add some text along a curved path beneath it. Imagine the motto beneath a coat of arms, or a product or company name beneath a logo.
Now, I tried using the text tool to add the text along a path, and I think that I now understand how that works.
Now it turns out that there is a feature missing that I would like to see, which is that text justification should make the text conform to the ends or centre of the path... by this, I mean that if I draw a path and the text is too short to fill the whole of the path, I should be able to centre the text along the path.
The way around this that came to mind is that if the path is a circle then I can place my text starting anywhere, and then rotate that layer to centre the text beneath the image.
So I make a circle selection, and convert the selection to a path... but the path seems to start at the top of the circle (I don't now what you want to call it: 0°, 12 o'clock, top dead centre, North?) and go clockwise... meaning that if I rotate my text to be below the image it will be upside down.
My work-round is to create a temporary layer and draw a circle on it, then use that as a guide to create a path along part of the circle in an anti-clockwise direction.
But I thought that there might be a mechanism for easily swapping the start and end positions of a path,another, better way if placing text below an image,a way of centring text along a path.
View 3 Replies
View Related
Dec 6, 2005
Need to create the text as below. (i.e i need to put my project name in Clock Wise what's the way to do it in photoshop ....
View 1 Replies
View Related
Nov 13, 2013
Is there a shortcut to draw a 45 or 90 degree angle from a drawn line on an angle using the pen tool? ie. Rather than just from the x and y axis.
I trace a lot of maps and site plans.
View 19 Replies
View Related
Oct 5, 2011
Is there a quick way to rotate an object to match an angle without knowing what the angle is? I am using AutoCAD 2011 now. I was using 2007 and I had an add on command the would rotate an object using a base point and picking the two lines that make up the angle, and it would match the angle you wanted. I can not get that command to load in 2011.
View 4 Replies
View Related
Jul 25, 2012
I have a property line that is N 36d19'52" E but needs to be N 12d52'18" E. The obvious and calculated rotation angle would be 23d27'34" but when I rotate the line by the calculated angle it doesn't rotate to the right angle. It's off by 0d11'10"!? When I draw a line by bearing at N12d52'18" E and inquiry the angle between the property line and the drawn line the angle difference is in fact 23d27'34".
View 1 Replies
View Related
Feb 11, 2011
Let's say I am inserting a square block into a dwg and want to get it parallel to an existing angled line. Do I have to read the angle of the line and insert the block to that angle or is there a quicker way?
View 6 Replies
View Related
May 26, 2013
I have used a driven contraint in a sketch.
Can that also be done in an assembly?
In one assembly I want to make one angle half of a driven angle.
View 3 Replies
View Related
Apr 7, 2011
Rotated text.cdr
How can I stop new text boxes being rotated? When I make a new text box (or start typing artistic text) using the text tool, the box (or artistic text) is rotated 90° clockwise. The tabs also show on the left hand ruler instead of the top one. I have looked at all the options in the Tools menu but there does not seem to a way of changing this. I have attached a CorelDraw file as an example.
I am using CorelDraw 14.0.0.701 from Graphics Suite 4. My PC is running Windows XP Pro, Service Pack build 2600.
View 5 Replies
View Related
Jan 16, 2013
mirrorclip.JPG
Just thought I'd share some stuff that can be done with CorelCAD.
Under export, you can export a STL or STereo Lithography file. These files can be sent to a 3D printer. Sometimes, when things around the house break or go missing, a quick measure with a caliper and some fast CAD work - then a half-hour or so in the printer will produce a new part.
CorelCAD is quite useful for that kind of work.
Here's some stuff I've done with CorelCAD and an UP 3D Mini printer, which makes parts in ABS plastic - and they are quite strong... So it's great to build stuff.
First project: A clip to stop my mirror wobbling. Took about 8 minutes to design and about 8 to print.
View 9 Replies
View Related
Jul 6, 2013
how to convert "real world" angles of elliptical arcs into those shown in a dxf file?
Say that I have drawn an elliptical arc with its start angle on 210 degrees and an end angle of 324 degrees. The values in a DXF file, for an elliptical arc, have something to do with the contant "PI" (3.14159). I know that a full circle is 2*Pi but how to do this with elliptical arcs!!
View 1 Replies
View Related
Jun 2, 2013
I am new to corelcad. In fact, I am looking at the trial to make my buying decision.
I have installed the trial of corelcad2013 and have opened a autocad lt file from autocad lt 2002 (I guess).
I see a black model page.
When I select all (ctrl+A) I see all elements selected.
Any way to get them visible?
View 8 Replies
View Related
