AutoCAD Civil 3D :: Export Parcel Analysis To Show Degrees Minutes And Seconds Instead Of Default Decimal Degrees

May 18, 2012

How do I get the export parcel ananlysis to show degrees minutes and seconds instead of the default decimal degreees. My direction settings are set to DMS, but I can't see where to change arc deltas...

(running C3D 2012 sp4, Win7 64bit, 8GB)

View 1 Replies


ADVERTISEMENT

AutoCAD Civil 3D :: Input Bearing In Degrees / Minutes And Seconds

Jan 22, 2013

when trying to input the bearing in degrees minutes and seconds I have to input (for example) 89%%d49'38". how do i change it so i can input ddmmss?

View 5 Replies View Related

AutoCAD Civil 3D :: Curve Label To Display Delta In Degrees / Minutes And Seconds

May 27, 2010

I'm using civil 3d 2008 and trying to lable my pavement radius with Line and Curve Label but the delta setting is only in decimal, how do i get it to read degrees, minutes and seconds.

View 4 Replies View Related

AutoCAD LT :: Set Line Direction By N E S W By Degrees / Minutes And Seconds

Dec 16, 1999

how to set line direction by N,E,S,W by degrees, minutes and seconds.

i.e.. drawing a plot plan laid out by a surveyor.

Must I convert to degrees for polar coordinates or is there a way to directly insert these angles?

View 8 Replies View Related

AutoCad :: Dsiplay Arc-degrees With Minutes And Seconds In 2011 For Mac

Oct 31, 2011

I would like to know, whether there is a way for diplaying arc-degree values not only in whole degrees but also including minutes and seconds. Couldn´t find a way to define this...

I am using AutoCad 2011 for Mac, Version 18.1.49.62, on a MacbookPro 2,1 (2,33 GHz, 2GB RAM; 17")

By the way, how do I create a signature for postings in here?

View 4 Replies View Related

AutoCAD Civil 3D :: Converting Decimal Degrees To Point ID

May 15, 2012

Is there a way to convert decimal degrees to a point id?  I have tried inputting the decimal degrees in as point but land no where close to the coordinate it should.  

View 3 Replies View Related

AutoCad :: Convert Coordinates To Decimal Degrees

Feb 22, 2011

I have a dxf file from a client created using autocad. What these coordinates mean -40 558.37E and -46 244.43 N. These are UTM? I need to convert to decimal degrees. How do I do this?

View 9 Replies View Related

AutoCAD Inventor :: How To Measure In Degrees And Minutes

Feb 20, 2011

How do I get Inventor 2009 to measure in degrees and minutes. Below is what I am trying to do.

View 3 Replies View Related

AutoCad :: How To Set WCS To Default 90 Degrees

Jan 27, 2013

Using acad 2010,I'm attaching an XREF to my drawing,But it comes rotated, I saw that in the xrefed drawing the wcs isrotated.I guess if I'll set it to pyre 90 degrees ill get it fixed.

How can I set the wcs to the defult 90 degrees?

View 4 Replies View Related

AutoCAD 2013 :: Setup Angular Dimensions To Show That First Zero If Minutes / Seconds Value Is Less Than Ten

Jun 25, 2013

Cannot find a way to set up angular dimensions to show that first zero if the minutes or seconds value is less than ten.

Desired: <degrees>08'05"
Stuck with: <degrees>8'5"

View 1 Replies View Related

AutoCAD Inventor :: How To Show Degrees Of Freedom Glyphs On A Sketch

Dec 12, 2011

This page mentions the degrees of freedom glyphs, but it doesn't say how to show them, and I couldn't find any ribbon button or context menu item that mentions them.

View 2 Replies View Related

Lightroom :: 4.4 Does Not Show WB Temp In Degrees?

Jan 2, 2014

My lightroom 4.4 does not show wb temp in degrees.  Does LR 5 ?

View 1 Replies View Related

AutoCAD Civil 3D :: Can Cut Corridor With (for Example) 45 Degrees

Nov 6, 2013

I have a corridor with  intersection.The intersection isn't  90 degrees. Can I cut corridor with(for example) 45 degrees?

View 9 Replies View Related

AutoCAD Civil 3D :: Surface Labels - Slope In Degrees

May 26, 2010

I'm just trying to figure out how to label my surface with slope values in Degrees. The existing options are rise/run, percent...

View 4 Replies View Related

AutoCAD Civil 3D :: Sid Don't Plot With DVIEW Screen Twist At 270 Degrees

Jun 12, 2012

plotting a MrSid using DVIEW TW 270 ?   Naturally we've spend 2 days on this.  DVIEW used to be a great way to create dynamic views...

View 8 Replies View Related

AutoCAD Civil 3D :: Why Does Linetype Change If Rotate Passed 180 Degrees

Nov 1, 2012

i have a simple fence line type with "x"s....if i draw the line straight up or to the right it looks perfect. but if i draw it anywhere to the left then the Xs are off centered.

View 9 Replies View Related

AutoCad :: Change Default Drawing Angle From 30 Degrees To Another Angle?

Oct 15, 2008

Im drawing in isometric view and want to change the default drawing angle from 30 degrees to another angle.

View 9 Replies View Related

AutoCAD Civil 3D :: Change Radius To Degrees In Horizontal Geometry Band Set Profile

Sep 25, 2013

How to set change the radius to degrees in horizontal geometry band set profile.

View 2 Replies View Related

AutoCAD Civil 3D :: Change The Format Of Lat / Long In A Point List Display From Degrees

Apr 4, 2012

Is there any way to change the format of Lat/Long in a C3D point list display from degrees, minutes, seconds to decimal degrees? I have looked pretty hard, but can't find anything. The geodetic calculator only does one item at a time, I think.  Any plug-ins out there? I suppose this could be on a wish list as well.

I am using R2012.and have ended up manipulating point values in Excel-not a quick way of going about it.

View 7 Replies View Related

AutoCAD Civil 3D :: Zero To Show On Angular Dimension For Seconds

Jan 17, 2013

How do i get the leading zero to show on an angular dimension for the seconds? as in: 108d 36' 03" ?

View 1 Replies View Related

AutoCad :: External Reference - Lock Up For 30 Seconds To 10 Minutes

Nov 1, 2012

I am having an issue with an external reference. It is basically a 3D drawing of a few trusses with truss bracing installed. I include it with almost every set of drawings. Problem is it often causes my AutoCAD to lock up for 30 seconds to 10 minutes. The problem occurs when switching from paper space to model space or when I load the drawing file.

View 3 Replies View Related

AutoCAD Civil 3D :: Parcel Reports To Show (reverse Curve)?

Mar 12, 2012

I have edited the "GeneralLegalPhrasings.xml" file used for the parcel report "General_Legal_Description_for_Parcels".

Two issues:  1. it will not label a reverse curve properly....it shows them all as "compound curves". 2.  A curve to curve is always shown as "NonTangent".

I've attached the .xml file (I only edited the imperial parcels - the second large group of <Metes>).

Quite simply, these two "types" below have the words "reverse curve" and tangent or non-tangent accordingly in the output phrase, but it only creates non-tangent compound reports.

Curve to TangentReverseCurve

Curve to NonTangentReverseCurve

This is the report from the parcel in the attached dwg file (notice the "curve to the left" -> "curve to the right" labelled as compound, and all non-tangent curve to curve):

From the POINT OF BEGINNING; Thence, North 90° 00' 00" West, 129.16 feet to a point for corner;

Thence, North 00° 00' 00" East, 100.00 feet to a point for corner, the beginning of a curve; tangent

Thence, 61.46 feet along the arc of a ____ curve to the right, having a radius of 39.13 feet, a central angle of 90° 00' 00", and a chord which bears North 45° 00' 00" East, 55.34 feet, to a point for corner, the beginning of a compound curve; non-tangent

Thence, 47.09 feet along the arc of a ____ curve to the left, having a radius of 29.98 feet, a central angle of 90° 00' 00", and a chord which bears North 45° 00' 00" East, 42.40 feet, to a point for corner, the beginning of a compound curve; non-tangent

Thence, 94.33 feet along the arc of a ____ curve to the right, having a radius of 30.03 feet, a central angle of 180° 00' 00", and a chord which bears North 90° 00' 00" East, 60.05 feet, to a point for corner;

Thence South 00° 00' 00" West, 169.11 feet to the POINT OF BEGINNING and containing 0.483 acres of land.

Civil 3D 2011
Windows 7 x64

View 3 Replies View Related

AutoCAD LT :: Rotate Plan 180 Degrees

Sep 15, 2012

Needed to rotate my plan 180 degrees.  So I typed in UCS enter then z enter then 180 enter and then plan enter.  My plan rotated and it looked fine.  I noticed my crosshairs where now green and red.  I needed to add more things to my drawings but the lines I was drawing do not look straight - they look bent and the ucs icon doesnt look square. I attached my drawing for you to see what I am talking about 

View 1 Replies View Related

AutoCad 2D :: Drawing Leaders At 90 Degrees

Jun 16, 2012

How do i draw a leader with all 90 degree angles. When i'm drawing a leader with an arrow for example and select two points it makes an angle.

View 4 Replies View Related

AutoCad :: Convert Pitch To Degrees

Sep 17, 2012

How do i convert pitch to degrees, in order to get the proper angle?

View 6 Replies View Related

AutoCad 2D :: Cross Hairs Are At 45 Degrees

Nov 16, 2011

I am an occasional user of AutoCAD. I have a received a drawing from a company where the cross hairs are at 45 degrees and I can only insert dimensions at 45 degrees.

I have tried PLAN > Enter > Enter . This rotated both the cross hair and the drawing 45 degrees

View 9 Replies View Related

AutoCad :: Setting 0 Degrees As North?

Apr 11, 2013

my default 0 degrees is set at east. setting 0 degrees as north, south etc

View 6 Replies View Related

Photoshop Elements :: Freezes Up After 30 Seconds To 3 Minutes Of Use

May 24, 2013

My Photoshop Elements freezes up after 30 seconds to 3 minutes of use.  What can I do to fix this?

View 2 Replies View Related

AutoCAD Inventor :: Sketch Flipping When Going More Than 180 Degrees

Feb 20, 2013

Here's the situation:

I have a tube, approximately 16" O.D., 14" high, and 1/8" thick. This is all a single part.

I'm trying to cut 3.5" wide and 4" tall slots around the top. The number of slots can be 1-6.

I'm driving the size and slots from a spreadsheet.

The orientation of the slots can have the first slot anywhere from 0 to 360 degrees. (FWIW, the spreadsheet redefines 0 and .0001 and 360 and 359.99).

Anyhow, as long as the first slot is between 0-180, it works just great. Once you pass 180, however, the verticals of the sketch flip so it's barely cutting the notch at all.

To make the cuts i've created a sketch off the top of the cylinder and drawn a construction line at 0 and another and put a driven dimension between them to set the correct position of the angle. I think create a workplane off that line tanget it to it's end point. At that point, draw sketch, extrude, etc.

I've also create a workplan off one of the origin planes and the origin Y axis that's perpendicular to the notch (angle driven by spreadsheet and equation in workplanes angle offset). Offset a 2nd plane tangent to the O.D. of the tube, created a sketch, extrude etc.

In both instances, when the angle crosses 180 degrees, the sketch flips on me.

What can I do to keep the sketch from flipping?

View 1 Replies View Related

AutoCAD Inventor :: Degrees Of Freedom Glyphs

May 16, 2013

If there is a way to change the size of the 3d glyphs which display the degrees of freedom of parts within an assembly ? I need to alter them to be slightly bigger.

View 1 Replies View Related

AutoCad :: Make Line Of 25 At Angle Of 150 Degrees

Nov 9, 2011

I am currently using 2010 version of AutoCAD and I am having difficulties sorting out my angles.

I need to make a line of 25 at an angle of 150 degrees. Upon doing this it always goes the wrong direction to which I want the line to be facing.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved