I am relatively new to Cad and would like to know how to properly use the align command. I have a rotated drawing I'm trying to match up with a drawing that isn't rotated and I need to be exact. I know I can use rotate and mess around for a few minutes to get it done but I know using the align command would save me a lot of time.
AS3: In component list my icon and label text are not align properly, when app is started, label text is over icon and when I put mouse pointer over any item in the list then alignment it's ok.
This is when I test flash app: And when I put mouse pointer over any item, alignment of icon and label is ok! Here is code:
Site layout has moved and rotated a little. Have spot elevation labels in my sheet but unable to use align command. Align command is able to be used but only moves labels rather than move and rotate.
when I attempt to use the ALIGN command (both from the command line and also the ribbon) I receive a response as follows Command: _align "The file geom3d(.lsp/.exe/.arx) was not found in your search path folders. Check the installation of the support files and try again.nil" I checked thru my programs and there is NO geom3d.lsp, exe or arx file. There is in Program files/autocad2013 folder a geom3d.CRX file. I attempted to copy the original geom3d.ARX file from release 12 into the same folder, went to place the folder in the working directory via the options menu but the directory wouldnt load from the Support File Search Path to the Working Support File Search Path so I placed it in the Program files/autocad2013/support directory and loaded this directoryinto both the Support File and WOrking Support directory which loaded but the following response showed "Command: _align Initializing... ARXLOAD failed" How can I get this command to work as it was fine in Autocad 2012 before I upgraded.
I am using the ALIGN command to overlay two groups of blocks, I'm then using some VBA code to export the coordinates of the blocks to an excel sheet to make comparisons.
The issue I'm having is when I use the ALIGN command the coordinates exported are different to those in the drawing (but only for those moved using the ALIGN command).
I don't get this issue when I use the move, rotate and mirror commands, only ALIGN. What may be causing this?
I am currently using AutoCAD 2012 and having problems with the STRETCH command.When I select 3 lines, then deselect 1 of them lines and then select the STRETCH command it does not stretch the selected lines.
Now this is the way I have done in it in previous versions and it has worked. (AutoCAD 2010). Our Company has recently moved to 2012.Is this a function that has been removed with this version or am I doing something wrong?
On ACAD versions higher than 2005 the STRETCH command does not work properly. The problem happens when selecting the items from the left to right. The item is MOVED instead of STRETCHED. It works normally when selecting item from Right to Left. However I need it to work from Left to Right so that I can individually select the item that I want to stretch. Because of this, I am still using 2005. Both 2009 and 2012 have this BUG, making them un-usable for my applications. I just got a new computer with 2012 version only, but I can't use it. I am trying to get 2005 installed on it now.
previously i was using civil 3d 2010, now while i am using 2012. i want to create a grid of points with easting and northing. i have manually created a point but when i use array command it does not work properly. as u can see in this image.
i created point with proper values of easing and northing but after array easing northing values becomes just -19.
I have been using the frame generator quite often and recently the insert frame command is not working properly. I would like to know if there is a fix/patch for this problem or do I have to re-install the program? I am very frustrated with this problem as I do alot of structural design and the insert frame command comes in very very handy.
Occasionally paragraph allignment works opposite for left & right align, usually on Illustrator documents with Russian type.
In additon on center align text I set my cursor to input a period at the end of a sentence, and the period instead gets added to the beginning.
In character palette language is set to English USA, this is point text.
I created a new point text and this is happening, if I paste text from another document alignment works fine, font is Arial black but happens with all fonts.
AutoCad 2011. I am having no luck when trying to drag a command from the Command List pane to the Quick Access Toolbar. I have success draging to Tool Palettes
I am currently writing a series of routines for setting the layers for text, leaders and dimension commands. The end goal is a system where any annotation command sets the correct layer for the duration of the command, then reverts back to the layer that was active before the command.
I have managed to complete all the code, and it appears to be working fine, I just have one question: I have used -layer "m" "Lay_name" etc... for all layer setting commands, rather than any code to see if the layer exists already. In my limited testing this seems to be suitable, nothing that exists on that layer seems to be affected.
I know how to write code to determine if the layer exists already and set the layer instead, but so far it seems unnecessary??
After installing the VBA Module, I get the message "Unknown command "VBARUN"". I've rebooted, restarted and tried reinstalling the VBA Module to no avail.
I press CTRL+9 to make the Command Line disappear while drawing. When I plot (or when doing a plot preview) , the Command Line appears again by itself. So I always have to turn the Command Line off manually after each plot
The bug still happens;
- if Dynamic Input is turned off or on - if I plot to a real device or in PDF - if the Cammand Line Palette i docked or floating.
This is not an issue in AutoCAD 2012 so I guess it has to do with the new way they programmed the revamped Command Line palette in 2013.
I need to save a drawing file and give it the name of my desire using a single command, I don't want to issue "saveas" and then specify the name in the file name prompt. This problem is has been faced when I was using ScriptPro and I couldn't succeeded to do that. Hence I need to know if it is feasible to do the stuff using a single command. It will be preferred if I can choose the location to save the file also rather than save the file to the default location.
without reiterating a lot of what is said in this thread: [URL] ......
This happen outside the potential malware infection?
if you care to not click-through, the problem is that certain commands (not all of them) simply do not disply in the command line. so the MOVE command for example looks like this:
I'm trying to align 1 to 2, Sketch up can let me align simply by moving and it will detect the face of object 1 to object 2, is there a similar way to do it in Autocad?
I'm trying to Align the Z Axis with 2 points, that works but I'm 90deg off around the Z Axis.
Shared Function UCSAlignZaxix(ByVal Point1 As Point3d, ByVal Point2 As Point3d) As Matrix3d
Try Dim ZAxis As Vector3d = Point1.GetVectorTo(Point2).GetNormal Dim yAxis As Vector3d = ZAxis.GetPerpendicularVector.GetNormal Dim xAxis As Vector3d = yAxis.CrossProduct(ZAxis).GetNormal Dim NewMatrix3d As Matrix3d = Matrix3d.AlignCoordinateSystem(Point3d.Origin, Vector3d.XAxis, Vector3d.YAxis, Vector3d.ZAxis, Point1, xAxis, yAxis, ZAxis) Return NewMatrix3d Catch Return Nothing End Try End Function
I’m wondering if there is a way to align texts in the AutoCAD with no work around. For example, in the ArcGIS we can select the texts and force the alignment.
Sure, in the AutoCAD, I can force the text to have the same x-coordinate to align them or other kind of work around, but why we don’t have this as a command like what we have in the ArcGIS?
I am having difficulty aligning the profile for a sweep feature. I need the profile to be normal to the path, but aligned vertically. In other words, the rectangular profile should remain "plumb" along the entire sweep. Is there a simple way to do this?
I have shared the sample files, trying to use the profile in two different ways, through Dropbox (they are too large to upload). I am using Inventor 2013.
How to align a model to the origin, and NONE of them seem to be correct. I am using Inventor 2013. I tried the move body command, however there is no part of the dialog box that lets me choose a face or plane to align to.
What to do when you import a model that is not aligned to the origin?
I am detailing a drawing with typical hole dimensions on a piece of steel angle. The drawing is setup such that the fabricator will have two options for each end of the steel angle. I have created two parts with the two options per end and have placed them outside of the page for reference.
I would like to reference each end of each piece, so that there are four pairs of views on the page (the two legs of the angle at each of the four ends), aligned in a grid. I have determined the best way to do this is with detail views. (Using breaks causes the break sign to appear huge, given the large gap I want between views. Using cropped views does not make it obvious that each end is a cutaway.)
My issue now is aligning the eight views. I know of the align options (horizontal, vertical, and in position), but they align to the "origin" of each detail, which is the center. With the angles being the same size, this works fine horizontally, but vertically, the pieces will never line up exactly, which is crucial to at least lining up the two legs of a single angle. The best I seem to be able to do is get the detail sizes as close to exact as possible so the centers come close to lining up. Even creating a projected view from a detail treats the cutaway end as part of the geometry, making it look a bit ridiculous.
way to precisely line up the views? I have done extensive searching and am confident that there is no inherent way to align based on a point or edge (seems like a deficiency on Autodesk's part), but is there a way to move the origin of a detail or something like that?