I am having difficulty aligning the profile for a sweep feature. I need the profile to be normal to the path, but aligned vertically. In other words, the rectangular profile should remain "plumb" along the entire sweep. Is there a simple way to do this?
I have shared the sample files, trying to use the profile in two different ways, through Dropbox (they are too large to upload). I am using Inventor 2013.
[URL]........
I am trying to sweep a profile throughout the helical sweep path which is a series of 3d sketches. The sweet prifile sweeps correctly to the first 3d sketch profile but whin I select the second line the preview is gone and Inventor gives me an error saying the sweep cannot be done. how I can have the sweep done throughout the helical structure.Attached is the ipt file.
View 3 Replies View RelatedMy purpose for Inventor (2012) is for cabinetry, more specifically the majority is for kitchen cabinetry.
All of our kitchens have crown, but not the same crown profile every time. There will be dozens of profiles if not reaching 100 or more.
What I am trying to accomplish is a way to model a sweep (which I can do no problem) but I would like to have the option of changing the sweep profile on the fly. I would be sitting with a customer and they would say "yes or no" to what they like.
I have looked at derived parts and iFeature and unless I am missing it, it's not giving me what I would like. Is this where iLogic comes in? How to use that, which I know I will have to eventually.
Right now I have an .ipt file with 7 crown profiles. Not sure I want to go any further for fear of re-work.
I am trying to perform a sweep of a profile and I am unable to select the profile. I have a part with a plane through the part. I created a profile on this plane that I want to sweep along my path. However whenever I try to select the profile I am unable to, even when I sectioned the part to the created plane.
View 2 Replies View RelatedI am working on Sweeping three helix profiles around a cylinder to create a screw thread. When I sweep the profile, Inventor gives me the error messages:
"The attempted operation would create a self-intersecting surfaces. Try with different inputs".
or
"The attempted operation did not produce meaningful intersection edges from the face-face intersection. Try with different inputs".
However, this is exactly what I need to create the helix profile I require and eventually increase the size of the Extrusion Sweep profile to 80mm. When I increase the sweep profile to 80mm I get the same error message about the self intersecting surfaces.
I am working with Autodesk Inventor Professional 2011, 64bit, 8gb RAM, Windows 7, Intel Core i7-2860QM.
The attached file shows a gear tooth profile that I need to sweep along the lines shown. The problem is those lines are not all parallel to the UCS The tooth profile is a region.
Is there a workaround to make this happen? I used to do this all the time in 2008.
I couldn't attach the file 'cause it wss too big so I saved it as a PDF but now I can't attach that because it is not a DWG
How do I attach a PDF?
I making a glass panel with a metal trim for a bank window teller family. How do I control the lineweights for the metal profile?
It seems by default wide lines are being used. I don't see an option in the family editor to pick thin lines.
While working in the conceptual mass environment, I have inserted a closed profile (1 polyline) from a dwg file.
What I need is to either extrude or sweep this profile as a surface, but obviously Create Form only gives me the solid option.
How do I go about doing this?
Can sweep profile cut up to the bottom of stair stringer?
Find attached.
It's possible in maya to sweep a profile along a closed curve? Like in 3DsMax, for example to make a window frame with a particular section profile?
View 1 Replies View RelatedI just created a wall sweep on a wall , but I noticed the sweep doesn't adjust to the wall profile, please see the second floor wall in the attached image. Is there anyway to make the sweep adjust to the profile of the wall automatically?
View 2 Replies View RelatedI'm trying to create a Tiled Skirt (150x150mm) profile or pattern to be used as Wall Sweep. Is there anyway to create this profile as the Family Template: metric profile (wall hosted) only allow me to create a 2D profile.
I would prefer to avoid detail lines or Filled region to get the tiles shown as I need to schedule and quantify this element.
I am attempting to model an internal 1/8"-27 NPT thread, both the through hole and the tapered part of the hole are modeled, but after I draw the helix and the polygon and orient the polygon to the helix correctly, (or even if I don't, I have tried it) it keeps saying unable to sweep object. I am using Sweep with Alignment with the No option. If I select the polygon first, then click sweep, it works, but rotates the polygon so that what I get ends up looking nothing like a thread profile.
I have tried reducing the polygon radius down to a ridiculously small value, thinking it might have been interference due to a possible trig miscalculation, but with no success, still have the same issue. FYI, I am using a .037" turn height for 27 TPI and a polygon radius of .0214", with a helix small end radius of .177" and large end radius of .189".
I am attempting to creating a complex profile of a window frame using the Edit Profile command within Sweep. It tells me that lines cannot intersect. How can I draw more that just a simple rectangular profile?
View 3 Replies View RelatedAny way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies View RelatedSolution to getting a horizontal sweep to miter with a vertical sweep? Or maybe there is a way to pick a path? A feature in the full version that Autodesk deemed unnecessary for LT.
View 1 Replies View Relatedgetting a horizontal sweep to miter with a vertical sweep? Or maybe there is a way to pick a path? A feature in the full version that Autodesk deemed unnecessary for LT
View 1 Replies View RelatedOn solidworks, There is an option to rotate the profile along the path as it sweeps. I'm curious if there is anything similar to that ability in Inventor? And if not, if there is a way to create a helix along a curved axis.
View 3 Replies View RelatedI have looked through these forums and found plenty of sweep problems and the answers to the problems but none for this particular type. I made a 3d intersection curve and am trying to sweep a profile along that curve but I keep getting the discontinuous segments error. I am using standard inventor 2011.
View 9 Replies View RelatedTrying to create a 3D sweep. I want to keep the sweep parallel to the XZ plane (like a parting surface). In the attached part, there is a SweepSrf3 that has sort of what I am trying to do, but it does not go all the way around the path. Notice how the sweep is parallel to the plane. I tried to do the same thing in SweepSrf4, by selecting the 3D Sketch1 as the path, Sketch2 as the profile, and Workplane2 as the Guide Surface. That failed.
In SweepSrf4, the only way that I could get the sweep to come close to working was to use the 3D Sketch1 as the guide rail and the circle as the Path. Seems like I need to use the circle as the guide rail and the 3D Sketch1 as the path to get what I want... but that fails.
Is it possible to sweep a solid along a 3d sketched line path to cut a groove / slot? This is like milling a slot in material on a milling machine so the cutter goes along a path removing material.
I can draw a rectangle that represents the side plane of a slot type cutter and this works but in the corners it is not working like a round cutter and leaves sharp corners which then need filleting to finish, but also I am not sure if it is cutting exactly as if a solid round/cylinder cutter would.
I tried the tube and pipe run to build this segment, and cannot select the route from the 3D sketch.
This route was based off of a 3D sketch made from included geometry from another part.
Tried sweeping too - and get error that the sweeping operation did not produce a meaningful result.
But I don't get the self intersecting error.
All this is is a .250 OD and .180ID profile that needs to be run through the path.
I included the part file.
am using Inventor 2012. Is there any way to select two rails when sweeping? One for the x and one for the y. I can only select one rail. If I choose Profile Scaling X & Y, it does not sweep the way I want to.
View 1 Replies View RelatedI have created a pipe using sweep through 2 planes and 3d sketch. I want a specific bend on that pipe to be extracted for drawing purpose. How do I do that ?
View 9 Replies View RelatedIs there some way to get the overall length of a sweep path?
We are creating a 3D sketch to run a pipe cross section along and for the final material we need to know what the LF is.
Inventor Pro 2013 (PDS Ultimate)
Vault Pro 2013
Windows 7 64
Xeon 2.4 Ghz 12GB
i used to use Solidwork's sweep-cut with a solid body feature but i can't find it in Inventor now.
Procedure:
In part file;
Create a second solid body (must be axis-symetric, like revolved feature),
Create a path that intersects with the solid (can be a line or a curve),
Sweep the solid along the path with cut command.
I need this where the sweep-cut with a profile is not enough, to get surfaces obtainable by milling on a cylindirical body on a helical path.
So I have a 3D sketch. As you can see in the image attached, there are circles on a 2D plane that are attached to circles on another 2D plane via all the purple lines. My goal is to do a sweep for each of the circles so that I can get a bunch of holes. However, after I do the first sweep, the sketch disappears (see pic 2) and I do not know how to go back to the sketch so I can sweep again and again.
View 7 Replies View RelatedWe are developing an equation driven 3d spline using VBA.
It generates a 3D spline, guide rail, and tool profile, but we're having trouble figuring out how to do the actual "sweep with guide rail" using the API.
Attached is an .ipt of the shapes our program is generating automatically. The problem is we are having to manually create the sweep after the geometry is created.
How can we automate the sweep with guide rail process?
Autodesk Inventor 2012
I am using Inventor 2012. I am trying to sweep the pink shape around the pink rectangle but I get a weird result. Can I not sweep around a rectangle from the center? See attachment. I want to add more to the shape but when I do the result gets weirder.
View 2 Replies View RelatedIm struggling coming up with a loft or sweep to get the design effect I need. see on the pic how the profile terminates to a point.
View 4 Replies View RelatedI am practicing modelling 3D sweeps using an intersection curve, and tried to insert a swept cut on the attached model, but the ends are not circular. I assume this is because the plane which I drew the sweep profile on is not on the top face. Is there an easy way to rectify this and create the semicircular channel in the ends?
View 3 Replies View Related
