I have this block. It's called Linear Stock. In this block, there are 2 visibility states. The one that I'm looking at currently is called Stretch with Angled Ends.
What I'd like to have happen is for the angles created when I stretch each grip to the proper location to be readable by a table or excel document. I know that I need a parameter for this to happen, but I'm not sure how to make it happen.
Using AutoCAD2011
So, In this drawing, I have 2 blocks. Stair, and stair section. The one I'm working on is stair section.
What I have is the base of a block that will automatically add steps to the desired height, at a 7" rise and 8" run. I have the array function working correctly. It is inserting correctly, etc.
What I'd like to do is to be able to stretch the frame by typing in the final height of the stairs, and have the length and treads adjust as needed. I'm sure that there is something in the xy parameter actions that I can use for this, I just don't know what it is.
Is there a way to have AutoCAD use the "right angle symbol" instead of showing 90 degrees when it measures right angles?
View 8 Replies View RelatedI have created the following code in VB.NET that i allows you to calculate the internal angle of a polyline. First delivery getting the angle of deflection, a ves obtained 180 you rest this and get the inner corner. All fine, as long as the polyline is the image-1.png. Otherwise, if the polyline is as in the image-2.png there is an error in the vertex B.
That algorithm could follow in order to comply with the correct value. Since later this data i presented it in a table of AutoCAD.
Public Shared Function AngleDeflection(ByVal pto3d As Point3dCollection) As ArrayList Dim anguloM As Double = 0 Dim vangl As ArrayList = New ArrayList For i As Integer = 0 To pto3d.Count - 2 Dim V As Integer = pto3d.Count - 2 If i = 0 Then anguloM = Math.Atan2(pto3d.Item(i).Y - pto3d.Item(V).Y, pto3d.Item(i).X - pto3d.Item(V).X) - Math.Atan2(pto3d.Item(i + 1).Y - pto3d.Item(i).Y, pto3d.Item(i + 1).X - pto3d.Item(i).X) vangl.Add(anguloM) Else anguloM = Math.Atan2(pto3d.Item((i - 1) + 1).Y - pto3d.Item(i - 1).Y, pto3d.Item((i - 1) + 1).X - pto3d.Item(i - 1).X) - Math.Atan2(pto3d.Item((i - 1) + 2).Y - pto3d.Item((i - 1) + 1).Y, pto3d.Item((i - 1) + 2).X - pto3d.Item((i - 1) + 1).X) vangl.Add(anguloM) End If Next Return vangl End Function
I want to draw the VW logo with AutoCAD, 2010 but the problem is that I do not know how to get the sizes/angles to draw it. how I can draw it?
View 8 Replies View Relatedi measure the angle between two lines. the value of angle is displayed in command line but annotation letters are so small i can't see them. i don't want to zoom to every angle i measure. how to make those annotations bigger size?
View 4 Replies View RelatedI am trying to bring an element (a building's floor plan) in one drawing into another drawing where it can be joined onto another building and the site plan.
The thing is, the UCS of the destination drawing is different from the first drawings. The Y-Axis in the destination drawing is pointing somewhere beyond the 3 O'clock position while it is still at 12 o'clock in the first drawing.
How do I determine the exact angle of the rotated UCS in order to insert the element at the right angle?
Where I can get a wheelchair drawing of all 3 angles?
View 1 Replies View RelatedI am using Civil 3D 2012. I am drawing a water line in a profile with a vertical scale of 1" = 10'. I am trying to draw lines at 45 deg angles to account for standard fittings.
Now, I tried to block a 45 deg angle and exaggerate the y scale, but for some reason this does not work well mathematically. Is there a way to draw lies at a certain slope, or at a certain angle from another line, while taking into consideration the scale exaggeration?
In a part file is it possible to find the adaptive workplanes used to create extrusion1. And then find if the two workplanes are at an angle with respect to the origin planes.
Have been looking for a while but it seems hard to find information on workplanes
When I create a line using dynamic input, I key in the length, TAB, and the angle. Is there a toggle setting somewhere that will allow me to enter angles greater than 180°? Drawing Units are set to Base angle north (270°) angles in D-M-S measured clockwise, yet dynamic input angles are measured from east (0°) both clockwise and counterclockwise. I.E. an input of 90° gives me either north or south, depending on where the cursor is located.
Ideally, I would like to be able to enter either 225° or -135° and have the line head off to the southwest. So far, I'm stymied and have to resort to command line entry. How to make dynamic input do what I want it to?
In the course of working up a tooling proposal, I attempted to replicate a 3D part from a customer print. While doing so, I noticed that 3D Sketch will not, under any circumstances that I can find, allow an angular dimension between a line and a plane. The customer print has two pipes projecting at odd angles from a base flange, one of which has an elbow. The print lists datum dimensions for the open pipe ends and the elbow, and gives vertical and horizontal angular dimensions to define the directions in which the pipes emerge from the flange. I have defined these three datum points in 3D space without any trouble, but Inventor 2013 will not allow me to define an angle between these sketchlines and the XZ and YZ origin planes, or between these sketchlines and the faces of the flange base I've constructed.
I am currently waiting on a proper 3D CAD model from the customer, and I'm considering longhand trigonometric calculations to place these lines properly, but I find it very hard to believe that Inventor is incapable of constraining a line to lie along what is effectively the surface of a cone.
Using:
Inventor 2013
AutoCAD 2013
I am using inventor 2012. Is there a way to ordinate dimension angles? For example dimensioning an irregular bolt pattern in a flange.
View 3 Replies View RelatedI want to create a segmented polyline with known angles / lengths, but I want to do this in 1 operation without having to copy/rotate/chamfer etc.
I'm sure it has something to do with UCS, but I've not used it in quite some time, I am stumped and everything I have tried so far has failed.
I have a arc that is about 21.5 radius and .5 in width. My problem is that it is going on a bench that i have made and the corner piece needs to be cut out and i am trying to figure how to make this line look like an actual piece. I can extrude the piece to 21 inches tall, but then i need it tapered back to fit this bench were making.
View 9 Replies View RelatedI face problem to draw angles. Normally angle are defined clearly but if they show the angle b/t two lines . Then may problem to understand . More clearly view image. I want to draw line with these angles more quickly and easily.
View 9 Replies View RelatedI am using a 2007 autocad version,is it possible to take dimensions like radius and angles on a 3D drawing?
View 1 Replies View RelatedHow does one measure angles greater then 180°, using the angle in measuregeom. i have tried the "Specify vertex" but it always returns the smaller angle, it is not a problem when you use angular in dimangular and specify vertex!
View 6 Replies View RelatedThe issue I have with Inventor 2010 is when i dimension a rectangle to be 44 in wide and 79 in height it becomes a slated rectangle. This event occurs on the work version of Inventor 2010. I have an educational version of Inventor 2010 at home and when I tried this same dimension rectangle at home it didn't have this issue. Is there a setting I need to turn off to fix this.
View 1 Replies View RelatedIf there was any way to get deflection angles of an alignment into a table? I finally figured out how to get C3D to label them using the add note label. If this is not possible, is there a way to make a table of the notes? I am using C3D 2013 version if it makes any difference.
View 4 Replies View RelatedI have a site plan that has buildings at different angles. How do I rotate my view so that the buildings are displayed at a normal x,y view?
View 1 Replies View RelatedI'm currently working on a Spa design and using new tools which is all new to me. I've used Draft Angles before but on a spa where you sit normally the sit reclines back.
Now I'm not sure how to do / show this in a 3D drawing. I've read and serached for different things but have yet to find something similar I'm looking for.
I've attached a PDF along with the circled area as to what I'm trying to accoomplish. Wanna be able to show the dip etc via Inventor.
If I am drawing in 3D and I want to draw a line with a specific angle, how do I choose the plane that it is drawn in? Cos whenever I specify an angle the line is drawn in the horizontal plane
View 2 Replies View RelatedHow do you draw circles along the circumference of a circle at various angles? for example i want to plot a small circle every 30 degrees along a larger circle.
View 9 Replies View RelatedHow can I draw lines with specific interior angles between them?
For example, if I draw my first line then, I want to draw the second one but with an interior angle of 100deg between them, what can I do?
Is there a function to obtain the start angle and end angle of a pline, i know arcs do.
View 4 Replies View RelatedBasically I have one hatch pattern that was used at different UCS values. The hatch patterns are correctly shown on the screen as shown in the attached image. But the puzzling thing is that they both have a pattern angle of 0.
I have been writing a program that globally changes hatch patterns, but the problem is that once I update the pattern, they all have the same angle. I need them to keep their current rotation when the patterns are updated. I cannot seem to find object access to what that actual angle is.
vla-get-patternangle does not seem to provide the data I am looking for.
I'm having problems getting Inventor to dimension using the current view option on an assembly. I ungrounded the assembly and constrained it to the angled work planes that I needed so I have to use the current view option, but when I try to dimension to the intersection of the angles, it won't give me a dimension.I'm using Inventor 2011.
View 1 Replies View RelatedI need to create an axonometric view of a model with specific angles (see attached). What is the best and quickest way to do this?
View 4 Replies View RelatedI have tried a thousand different scenarios with the new pressure pipes. When I create a new parts list and try to draw a water line, the compass only gives me 3 angles. This is using the "out of the box" templates.
View 5 Replies View RelatedI have just created a cylindrical object with an extrusion length of 300 mm and then created an assy(.iam). On to this cylinder i have placed a plate at right angles to the axis of the cylinder
What i wish to do now is mirror this plate.
It would appear the best way would be to create a work plane(mirror plane) thro the centre
Of the cylinder,however, how can this be done if when requested to create the plane 3 points are required,am i missing something here.