AutoCad :: How To Set Drawing To Layout And Print It
May 22, 2011how to set out a drawing to a Layout from model space?
View 7 Replies
ADVERTISEMENT
AutoCad :: Use Layout To Print - Scaling Drawing
May 25, 2011Scale in Layout. I drew my drawing in mm , and I want to use Layout to print it like I saw in a video, but how do I scale my drawing? For example, the counter and shelf I drew is 1:1 in the Model workspace(1600 by 2000mm) but in Layout, for printing on to an A3 sized paper how do I get it to print in 1:40 or something of that sort?
Right now I'm printing by using Fit To Paper with the dimensions included, but I notice our contractors are using 1:30, 1:40 etc. , my boss doesn't mind since I include the dimensions but I reckon it might cause problems in the future.
And is it possible to just select anything in my selection window, even 3/4 of a line? Because right now, I can only select the whole line no matter what, I only want 1/2 of it because I want to cut the whole drawing in half and move it apart.
By the way, is it possible to customize the panel? Instead of switching between tabs constantly, can I make my own panel? I googled this and tried using CUI but it is confusing. I just want certain sections grouped into 1 bar. Like... Draw/Modify/Attach/Windows all on the first panel.
I really want to be able to type in certain commands without hitting Enter, is that possible? If I hit M, it will move the object without me hitting Enter. Can that be done? Maybe not M, maybe Alt+1 to move, Alt+2 to Scale etc. etc.
AutoCad :: How To Print Multiple Drawing In One Layout Combined
Jun 19, 2013I want to print multiple drawing in a single layout (see picture) . It is possible in autocad to setup printing once? For example: One project contains 100 A3 drawing, one layout contains 20 A3 drawing. Up to now, i print to pdf separately, and i combined the 100 pdf in one file.
And i print from this file. (only in this way succeed to print collating multiple copies). But if the project changes, I could start all over again. Is there a solution to publish an combining the sheets to print immediately?
AutoCad :: Print Or PDF Drawing In (8.5x11) Layout View?
Apr 5, 2012My issue is this: While trying to print or pdf a drawing in (lets say 8.5x11) layout view, the edges get cut off. It looks as though the template I copied is too large to be printed in full. If this were the case, wouldn't it be the same even if I tried printing in extents? It still does the same thing printing in extents.
I am using Mechanical 2012.
AutoCad :: Trying To Show Only Portion Of Drawing In Layout To Print
Feb 2, 2014How to get only part of the drawing to show up to print. I've drawn a floor plan and have copied it several times. I have also drawn several patterns that represent a few different floor tile layouts and then put them over each floor plan and after some trimming I have a variety of options that someone can choose from for floor tile layout. I'd like to show each one on a separate sheet and of course when I go to layout the whole drawing comes over and how to only show one floor plan at a time.
View 4 Replies View RelatedAutoCAD Print / Plot :: Why Drawing Plots Results Using Viewport Scale In Layout Is Not Accurate?
Oct 8, 2013why the drawing plots results using the viewport scale in the layout is not accurate?
View 1 Replies View RelatedAutoCAD Print / Plot :: How To Print Multiple Layout Pages In A Printer
Oct 14, 2012I have multiple layout pages (58 pages) and would like to print them in a printer at once. How do I do that?
Currently, I open 1 layout at a time then print it 1 by 1, in which its killing me specially if I do have lots of drawings.
Publish does saving in DWF, PDF... But does not print in the printer.
AutoCad :: 2012 Layout Print And Designjet T2300 / D Size Incorrect Print Rotation
Jun 13, 2012I have a template with layouts of different sizes that had been working fine with a previous Xerox 6204. My D size and E size automatically oriented with the 36" side parallel to the roll feed. I have since moved to a job that got a Designjet T2300. On this machine the D size orients the 24" side parallel. This wastes 1' of paper on the left and uses 1' extra as it runs the 36" side perpendicular. I have been unable to rectify the problem. I have tried printing in portrait, that actually cut off some of the image. I have tried all types of rotation within the driver and layouts. Tech support had me going into the machine settings and set rotation to 90. Nothing. There is a warning that "HP utilities" is not installed. Could this be a remedy? When the tech came to set up the printer he installed the necessary drivers but mad no mention of this utility.
AC2012, HP desighjet T2300
AutoCAD Print / Plot :: Change Print Limits Of A Layout
Sep 12, 2012I’ve done it before in the past so I know its possible but I have forgotten how. See the attached image I would like to change the printable area of my paper space layout.
View 5 Replies View RelatedAutoCAD Visual LISP / AutoLISP :: Insert Another Drawing Layout Tabs Contents In Current Drawing
Mar 7, 2013I want to insert another drawing layout tabs contents in current drawing.
It's easy for MODEL tab, but for LAYOUT tabs, I dont know how!?
I prepared a code for INSERTING MODEL tab in current drawing:
(defun INS_DWG (TAB path dwg P / blk)(setq blk (strcat ""*" path dwg """));(setq N (vla-get-count (vla-get-layouts)));;Number of LAYOUT TABS in dwg(if (or(= TAB 0) (= TAB nil))(command "INSERT" blk P 1 0)); TAB=0 or omitted ==>Insert MODEL;(if (= TAB 1));==>Insert the 1st LAYOUT in dwg file;(if (= TAB 2));==>Insert the 2nd LAYOUT in dwg file;and so on....);;;usage:;;(INS_DWG 0 "c:\test\" "test.dwg" '(0 0))
Lightroom :: Print Layout Not Matching Final Print
Sep 26, 2012Epson 3880.
Lightroom 4.
Moutain Lion.
All current.
I am trying to print on 5x7 paper. I set the page setup to 5x7. I have the margins set to .2" on each side. The layout image inside Lr looks exactly how I want it to.Then I print. I end up with a .125" margin on the left and top, and a .625" margin on the right and bottom.
AutoCad :: Print A Floor Layout
Jan 18, 2013I want to print my finished floor layout but this layout view tab (layout 1) show me a tiny drawing I want it to cover all the A4 format
print.jpg
AutoCad :: Print Multiple Layout To PDF At Once?
Jul 6, 2012How can I print multiple layouts to PDF at one time?
View 9 Replies View RelatedAutoCAD Print / Plot :: Preparing A Layout Space
Aug 7, 2013I have an A4 peice of paper and need to change the scale of my drawing so it fits onto the page. I remember there was a short cut, but have since forgotten it.
It is currently at 1:1 and want to change that to a more appropriate scale.
AutoCAD 2010 :: Crash When Print Layout In Windows 7
Nov 3, 2011I tried to print the layout from autocad, the autocad will freeze and it will prompt out the AutoCAD Application error message as the attachment below. Once click on "cancel", the application will shut down itself.
*The printer is HP LaserJet P5225.
*Other program like Revit, MS Word and etc still able to print well.
*Computer spec: Windows 7-64bit, 12 GB RAM, Xeon processor.
*Installed with the HP original driver from original disc that given
AutoCAD Print / Plot :: Aligning Title Block In Layout Tab?
Jan 6, 2014Many times when I receive a drawing from an architect, when I go into the layout tab the titleblock info/XREF doesn't line up with the page layout. I would assume it lined up when the architect sent it to me in his software. For years the solution I use is to XREF the architects PDF in the layout and then go to print and change the Print Offset till it looked right in the print preview. Then I would apply it to the layout. I would then take the offsets and apply it to every sheet. This is a very time consuming process and was wondering if there is a better way to make this work and still keep the scales. I was also wondering if there was a way to move and align the layout on the fly in the paperspace.
View 3 Replies View RelatedAutoCad :: Print Viewbase Layout With Large Scale Factor?
Apr 21, 2012How to print a viewbase layout with a large scale factor? The problem I'm having with ac2013 is that the print is coming out with jagged edge.
View 9 Replies View RelatedAutoCAD 2013 :: How To Print Bing Live Maps In Layout
Dec 16, 2013How do I print drawings with such maps. I cannot seem to find the way to make it print in the layout. Otherwise it is a great new feature!
View 4 Replies View RelatedAutoCad :: Drawing For Each Layout?
Nov 3, 2011I have been using one drawing with in 50 Nos. layouts. Now I want to make the separate drawing for each layout. What should I do? Is there any lisp for do the above function?
View 8 Replies View RelatedAutoCAD Civil 3D :: Labels / Text Aligning To Layout Print Out Very Bold
Sep 17, 2013When I have my alignment labels and plan view text align to the layout view in Paper Space they plot out very bold.
I am using Style: Swis721 BT-Italic. I use that style in the profile for labels and in plan view. When I plot out the sheet the profile view plots good but the text that was aligned in the plan view is very bold.
AutoCAD Print / Plot :: Change Page Setup In All Layout Tabs
Nov 8, 2003I get several dwg's a day with up to 40 layouts in each one. All the settings are correct ACCEPT the plotter. Is there a way to set all page setups for all layouts at the same time? Something like select all layouts and do a page setup for all. Possibly with LISP or VBA?
View 5 Replies View RelatedAutoCad :: How To Create PDF Of Drawing From Layout
Feb 12, 2013recently switched from 2007 to 2010. All of my dwgs in 2010 were created in 2007. When trying to create a pdf of any drawing from any layout...adobe has difficulty reading layer/plot style info...it prints everything gray. I've tried pretty much everything and now think it has to do with importing something (maybe plot style?) from my earlier version? I don't know... need getting my plot style to be read properly by adobe.
View 2 Replies View RelatedAutoCAD LT :: Orientation Of Drawing In Layout
Mar 15, 2011A client gave us a file in which the drawing in model space has an orientation wherein the N is in positive y-axis. But if I go to layout (viewport), the orientation of the drawing is different, N is 45 deg from the x-axis. How does the orientation of a drawing in layout (viewport) changed without changing the original orientation of the drawing in model space?
View 9 Replies View RelatedAutoCad :: How To Make Each Drawing To Be Placed On Different Layout
May 9, 2012In the model space, i have 1 sheet and have 3 different drawing in it( lets say , i have a circle, a polygon, and a rectangle).
How can i put the circle on Layout1 , the polygon on Layout2 and the rectangle on Layout3.
AutoCAD Print / Plot :: Named Page Setups Don't Stay Assign To Layout Tabs?
Feb 24, 2012We have, since moving to 2012 had an issue with our standard Named Page Setups in our DWT file staying assigned to the layout tabs. When you click up to plot a dwg... the Page Setup Name indicating that the Named Page Setup assigned to the plot configuration dialog box says <None>. Even if you click in the drop down and select a setup... the name selected shows as selected after the box colapses... but then a split second later, the box defaults back to <None>.
View 2 Replies View RelatedAutoCAD 2010 :: Converting A 3D Drawing To A 2D Layout?
Feb 15, 2012I am having an issue with a 3D drawing (xref) with size very large and crashing due to lack of memory. I want to compress it into a 2D layout. How do I compress a 3D drawing into a 2D drawing or something much smaller than the 47 MB it is now?
View 3 Replies View RelatedAutoCAD LT :: Drawing In Layout Not In Model Space
Apr 20, 2012I have received a drawing that is only showing in the first layout tab on a contractor's template. The drawing is in a viewport of course. The drawing does not show in the model space.
1. Is it possible to send a drawing only in the Layout tab?
2. Is it possible for me to do something to view the drawing in model space and how is it done?
3. Could it simply be a compatibility issue between the contractor's.
AutoCAD Inventor :: Surfaces In Layout Drawing
Jul 12, 2012I've been doing a layout drawing of a plant
The floor of the plant is split into different faces to denote walkways etc.
When i saw they were missing from the drawing i thought it could be because i haven't 'included surfaces'.
I clicked on include surfaces on the model and it worked!
However, when the green arrow update finishes, they disappear, and the include all surfaces box is unticked! i didn't untick it, so what did?
Inv 2013 64bit
AutoCAD 2010 :: Output To PDF / In One Layout With Many Drawing
Feb 17, 2013I am new user in AutoCAD 2011.The situation is:How can I output to PDF when one Layout with many drawing?
I know how to output to PDF when one Layout with just one drawing(use Page setup + Publish), any many Layout one of them just with one drawing.the attachment will show you the 2 situations
1) one Layout with many drawing
2) one Layout with one drawing
AutoCad :: Company Logo Into Drawing And / Or Layout?
Mar 30, 2011how to put my companies logo into the drawing and/or layout.
View 1 Replies View RelatedAutoCad :: Copy / Move To End A Layout Tab In A Drawing
Jun 23, 2011Using AutoCad 2011. When trying to 'copy/move to end' a 'layout' tab in a drawing, I keep getting the message:
'ERROR:Copy of layout failed'
I have in the past been very successful operating this command in earlier vers of Autocad.
