How does it work? I see in the properties after I high lite it. Annotative Scale no/yes. We xref one drawing into other drawing and the view scale changes. will my hatch look the same or will the smaller view scale look really big in the drawing.
View 1 RepliesI make a drawing1 with layers on it and then I made another drawing2. I Xref the drawing 1 as my reference , where I put the column of the building. When I open drawing 2 referencing drawing 1, my scale is different. my inches scale is becoming feet when referencing in drawing 2. I put the same LTscale and limits in both drawing
View 4 Replies View RelatedI am trying to xref a base drawing. But everytime I insert the drawing, the scale factor always comes up to be 12. I tried changing it, but it won't let me. I have attached an image of the problem I am getting.
View 1 Replies View RelatedIs there a way (IV2012) to have the drawing view default to 1:1 when inserting a detail into the sheet? Now it tries to select a scale based on who knows what.
View 8 Replies View RelatedI can control the size of my main drawing views using ilogic based on the models extents as there is a direct relationship between a parts length and the drawing view width. however, I have several isometric views that I scale according to the model size but in certain configurations of my model the ISO’s are completely the wrong scale for that particular view where the main views are ok.
I have a set area on my drawing sheet for the iso view and it would be more beneficial to control the size of the view rather than the scale of the view. I can read the height and width of a view so why can’t I control the size of a view but the height or width?
I am working on an architectural drawing and for some reason when I try to "objectscale" the annotation to the same scale as the view port I am using, it doesn't appear or if it does it is a lot smaller scale than I requested.
View 4 Replies View Relatedwhat i am trying to do is create an iLogic rule that if your drawing view scale is set to the following ...
1:1, 1:2, 1:4, 1:8, 1:12, 1:!6, 1:24, 1:32, 1:48, etc. on the view label for that view it will diplay ...
SCALE: 1/2" = 1'-0"
and so on for the rest for the standard scale factors.
i know it will be some sort of a loop and it needs to check all views when ran for any changes.
i have never done any coding for the drawing side of inventor yet only model coding
i have a template, created a viewport and fit the model view in the layout space. However, when i scale the template... the viewport model doesn't follows the layout scale. Is there any ways to fit it so that when i scale the template i don't have to set the view again.
View 8 Replies View RelatedWhen I open a new drawing in my AutoCAD 2013 that I just recently installed last week, I encounter a problem that I am not familiar with from previus versions of AutoCAD I have worked on. First of all, the units default to decimal, and I want them to default to architectural, with feet and inches. I have to type UNITS in the command line every time I open a new drawing in order to adjust this. I have AutoCAD for Architecture 2012 on another computer, and the program automatically defaults to architectural units upon opening up. Just to let you know, the program I am having this difficulty with is part of a package called Autodesk Building Design Suite 2013. I was under the impression that it included AutoCAd for Architecture, but I think it has only standard AutoCAD.
The scale of the objects I draw vs. the scale of the drawing field is very out of proportion. What I mean is, when I open a new drawing and draw a 30' -0" line, the line appears so long on the screen that I cannot see the whole object, even if I zoom out to the maximum. I should be able to see the object in it's entirety. In fact, when I draw a line that is only 12" long, even when the zoom is all the way out, the line looks huge in length. I have tried adjusting the units to the architectural/inches setting of course, and I have tried adjusting the scale in model space from 1:1 to 1/4'=1'-0", but nothing is working.
I have drawn my blocks and text using annotation scale. When I xref the legend which has also been drawn using annotation scale, I cannot set the scales. That is annotation scale does not work when I use xrefs.
View 0 Replies View RelatedI have a file that is x-reffed into another file. In both instances the drawing has the same measurements, but when I make a viewport in the receiving file the drawing (in the viewport) is 1000x smaller than it should be. It should be noted that I am working in metric units AutoCAD 2011.
View 5 Replies View RelatedWhen I have placed dimensions in model space with a text height of 2.5 now do I get them to a readable size in paper space
View 9 Replies View Relatedi have a structural xref drawing that has all the text 10"high. I xref (overlay) that drawing into another one, but that drawing is going to have a scale 1/4"=1'-0" is there a way to auto scale all the text in to xref to become 4" high?
a bit more information
the structural drawing that im xrefing in will be overlayed over my floorplans, then printed at the 1/4"=1'-0"
I need the structural base drawing to keep the 10" text height because some times i have to print off the entire structural plan separate.
I am having some problems getting the hang of applying the drawing scale to my assignment. I understand the scale factor that is applicable to the printing only and that AutoCAD doesn't care about the units used...but something is not clicking here and I'm sure it is pretty simple. My assignment requires me to draw 3 simple structures at 1/8" scale on 11X17 paper. Each house is 20' long with 10' walls and each is done in absolute, relative, and polar. I actually completed the work with all 3 formats without specifying the scale or paper size, just to get familiar with the commands. But now that I am trying to set the dimensions correctly, I cannot replicate my work because I'm getting lost in the way things are defined. I am using AutoCAD 2005, also have a 2002 version to which I can defer.
View 9 Replies View RelatedI'm inserting an xref, and its coming in at a weird scale.... I noticed that in the 'external reference' dialog box the 'block unit' scale factor is set to a weird scale (.0394), but it will not let me edit it.
View 5 Replies View RelatedI have several .dwg files which I attach using XREF so that I can ensure I have the latest versions combined.
The problem is that the line types do not show up correctly. After looking up on google I have found that this is a problem due to it being a 3d model rather than it being flat.
I managed to half solve the issue by inserting each drawing into one, then exploding the whole image. Then changing the scale in the bottom right to around 1:200 to make the line types visible.
My problem is this ends up being a lot of work as the separate drawings can be updated daily. Is it possible to have all the drawings Xref'd in and to be able to have the scale changed to be able to read the line types? I tried to save the XREF setup as a template, then just bind all the drawings into one, explode and change the scale. But for some reason this doesnt work for me. I end up with just solid lines, rather than line types. I don't the drawings are made up of several lines, all of different length. (This I have been told is why the scales do not appear correctly)
I have been shown one method to work around this, which is to open the Xref drawings, explode them, then take each section of line and manually change each scale to the biggest that shows up.
I've got a drawing that contains an XREF. I've got a field reading the viewport object's Custom scale>Use scale name. However, whenever the drawing is loaded up all of the XREF's scales get imported. Since they contain the same scales, the field changes to read the XREF scale instead of the one it was set to. They are the same scale, but the field reads the XREF one first. Here is a screenshot showing what I'm talking about. Notice that the viewport's properties never show the scale as 1:20_XREF, but the field does.
I've been having to click "show all scales", do a SCALELISTEDIT, remove the XREFs, then do a UPDATEFIELD. I have to do this every time the drawing is open. It stays that way until C3D is closed. This becomes a problem when I go to PUBLISH a sheet set. If I haven't opened all the sheets in the sheet set and changed the scale list then they all get the wrong scale list shown.
Infrastructure Design Suite Premium 2014
Civil 3D 2014 x64
Windows 7 64-bit
6GB RAM
I realize it may be a Civil3D question. When I change my drawing scale in the "Drawing Settings" dialog box to 1"=40', for example. The Annotative scale in the Properties Palette changes to 1"=40'_XREF.
View 2 Replies View RelatedAs a part of a 3D Cad course I am doing I have to use the slice command to obtain a section view of my model . Wblock is then used to copy to file and then oops used to get full model back. I have to produce numerous views including 3 of these sections in paperspace .Where and how do I xattach these section views . I have tried a few different ways without success.
View 0 Replies View RelatedI'm a document controller that is trying to ID the situation with 2600 drawings. Some files are so large - 250,000kb, they won't open. They have bound xref's in them. We want to ask the contractor to unbind them and attach them as normal xref's. I need to view if a drawing has bound xref's. I just want to see them as BLOCKS which I now understand they are. How do I do view the blocks that were once xref's?
View 9 Replies View RelatedI am working with a seris of 3d views that I want o make bigger. How can I do this.
I want to keep the view the same but changed the "scale" of the view/perspective
I am simply xref'ing a profile drawing into a sheet drawing to print out. AS shown on the attached, when the profile comes into the xref I lose all the band data and the EG line does not come in as a dashed 2 line as the layer is set to. It almost looks as if the PL linetype generation is off for this line.
View 1 Replies View RelatedI cannot xref a construct into a view dwg using PN. I get error "Could not reference file <construct> in <view>. Same problem whether I use relative or full pathing. But I can manually attach the construct using the XREF command. So I know it is not a file/folder permissions problem. What's annoying is that I did get it to work with one construct but not another.
I am using ACA 2013 and I see that there is a service pack 2 update.
Is it possible to have the parent view for the section in one drawing and the child views in another drawing?
View 2 Replies View RelatedAfter upgrading to Inventor 2014 we notice that the graphics do not work properly, and that the overall performance in drawings and modelling bad compared to 2013. Then we installed SP1 and now drawing views are disappearing, however when we select "shaded" view the view reappears and works perfectly..
Any workaround regarding disappearing views?
Each time when I place a part in base view, have to follow few steps; go through view label, format Text, than choose type option - [Properties-Model] and its property - [Part Number], than placing dimensions. it takes long time and very repetitive, especially, when placing a hundreds of parts and I was wondering if there is an option, to set up view label; [Properties - Model ]& [Part number], as a DEFAULT. So, each time placing a part, in base view it will come up with correct label. Also, overall dimensions, can it be retrieve using parameters of the part?
View 4 Replies View RelatedA question about ex referencing. Can it be done within a drawing. In other words, can I can Xref the plan to another part of model space to then create the elevations in UCS, and then Exref the elevations from USC to a horizontal line.
This would be very useful in the sketch plan stage.
Suppose I have a Drawing Structure like:
MasterRoot
Root1
MasterChild1
Child
MasterChild2
Child
Root2
MasterChild1
Child
MasterChild2
Child
When I use XrefGraph xg = mainDb.GetHostDwgXrefGraph(true); in Code then I get all the Files as a node including MasterRoot (say count=6).
If I want to get Only direct Children (here, Root1 and Root2)(means count=2 only), then what i have to do?
Is there any advantage when inserting someone else drawing into yours to xref it rather than copy and pasting into your drawing?
View 1 Replies View RelatedI have an operator here who has an XREF that he brought in and it did not line up as it should with the remainder of the drawing. He then went in to the drawing being XREF'ed and reset the origin so that it would line up properly. When he did so, the XREF did move but no to where he set the origin. The XREF is still showing the insertion point some place other than where he has the origin set on his XREF'ed drawing.
View 6 Replies View RelatedI have a main drawing that I want to pull into another drawing as an XRef. When I try and attach the drawing as an attachment I get then message *Invalid* in the command line.
I have taken the drawings off the network and put them directly on my computer to make sure that it is not a network issue, but I still cannot attach the drawing.