I want to draw a section with thermal insulation line without the boundary lines of main profiles and rivets. in fact thermal insulation should be around and back to main profile and rivets.
i used linetype batting and i can not do that. how do you deal with that?
how to create a lisp to draw the rigid insulation as attached.
View 6 Replies View RelatedRoutine that will draw a insulation hatch around a circle?
View 9 Replies View RelatedI'm more or less happy with annotation scaling, apart from the mysterious hatching problems that are not the issue of this message.
But there is a major annotative scaling issue with batting / insulation lines. Insulation lines should NOT change with annotative scaling ! A 4" insulation layer shouldn't become 16" just because i'm printing in bigger scale !
C3D 2012...but this feature has probably been in C3D for sometime
1-What is a 'Line Marker in Section' Section component of an Alignment Style?
2-How is it used (example )?
why my section is not parallel with my section line. I did constrain my section line in the section line sketch.
View 2 Replies View RelatedI have a problem with a recently downloaded version of Inventor. When I start a new drawing all I get is a blank blue screen instead of one with a grid display. If I start a line I can see the cursor change to draw the line but a line does not appear. I don't know if it something with how I installed the program or just system settings.
View 2 Replies View RelatedHow can I draw a straight line without that protractor shaped dotted line following my cursor making it lag and also not snap correctly to the next line? Also, I have noticed that I can't set my user interface to auto cad classic settings. There seems to be no option for it in workspace settings.
View 3 Replies View Relatedin autocad we use offset commend to draw a parallel line to another line what we should we use in Chief Architect x2
View 1 Replies View RelatedHow to draw a line that STARTS at a perpendicular angle to another line ???
View 4 Replies View RelatedI saw thermal properties in the list of Inventor's materials. However, I didn't find how to make a thermal analysis using Inventor MEF. Is it possible?
View 3 Replies View RelatedI have survey points for a water course and want to draw l-section, which command I should use to draw polyline l-section from all those points in one command.
View 8 Replies View RelatedI have a cube and I want to create a section plane that goes trough the middle of 3 edges that have a common point. After this I should be able to erase the smaller solid and keep the bigger one. If needed I will attach an image to be better understood.
View 4 Replies View RelatedI don’t know if there is some way to draw, or somehow to say to AutoCad that it let me to input measurements from line but not from main base pint.
For example in Revit I can make angular dimension between lines and then apply any angle that I want, maybe AutoCad has such tool?
I was drawing a lot of lines with the pointer that stuck at the end of the line and after that it stuck at the beginning of the other line (i hope you understand what i mean). I don't know what i pressed but now this function is not active and is very difficult to draw the lines.
View 3 Replies View RelatedHow do we do a break and or jog line in a section so we make things shorter? I did find the DIMJOGLINE command and that will be great for the dimensions but what about the other stuff, do we have to do that with a block or draw the thing, if that's the case what are you doing to handle this?
View 5 Replies View RelatedI am trying to do a drawing but there's a function I forget. I want to start a line from a section of another line. How to do something to skip a distance from a start point of a line to the position you want.
View 5 Replies View RelatedJust learning 2D CAD and trying to draw a cross section of a timber winder stairs as the strings change angle (I think) at the winder section. Looking at 3nr winding steps.
Setting out a standard stairs is okay, so I have the floor to floor height.
I must have pushed one or the other button but I don't know which one!
I use CS5 and have now a small arrow on my line segment tool (as shown in the picutres):
Ever since that when i click shift, it just allows me to draw vertical lines, rather than vertical or horizontal.
when I (try to ) use Pencil and Brush tools, (cross-hatching), some lines get erased/replaced by the lines drawn close to them. It must have something to do with the preferences, but I am not sure what to change/adjust.
View 2 Replies View RelatedI have a b&w image (greyscale) that i want to colorize based on the greyscale. Some thing the provides a thermal or in this case a colorized pressure map. I
In this case it is a like a stamp. Replacing the blacks with red and down toward blue as on the grey scale.
1. if i draw a line using the line tool.. can i curve it to say 40 degrees like i can with the text function?
2. So ya that one was easy.. hows bout when i want to cut something out ACCURATELY, the pen function, right? (according to a friend)when i make all those little boxes and select the area i want to cut, all that gets copied are the outer lines, which i presume is what ive just drawn.. how do i cut the area inside this?
3. and finally maybe a slightly less easy one- In Paint, when you cut out an object and paste it, you can select for the white of the image to become transparent so you can paste over what you have already.. is thee a feature in PS for this?
At the top of the clock, how do you draw the curved lines, which say radius of 4.
[URL]........
In model space I draw a line with a particular linetype, say a fence row, and I adjust the linetype scale so that it reads like I want it, but then when I go to paper space, it's just a plain line no matter what I set the linetype scaling to?
View 9 Replies View Relatedhow do we draw a tangent line in autocad
View 1 Replies View RelatedI have created a layer for the dashed lines, but they continue to be solid lines.
View 9 Replies View RelatedI want to load a text file, the file is in X,Y format. I want to draw the line on this file without have to enter the x,y coord one by one.
View 2 Replies View RelatedHow to draw a line with given angle at the end? What is the command?
View 4 Replies View Relatedwhen i draw a line with 4 units in autocad the line seems as small as a point but in the example i watched it was long enough so how can change line length shown and in the another example i watched after clicking the line command and specifying first point the user was typing a length in the command line as 4'7-1/2 and clicking enter.after this the line's direction and length was automatically forming.but when i doing the same it doesnt work.how can i do both of these.
View 9 Replies View RelatedMy question is: Why certin AutoCad files, I'm not able to draw lines?
I'm in model space. I can move objects. I can even erase/delete things. But I'm tring to edit this shop drawing, i need to add some details, so i need to draw some lines. I use the "l" command. Select my 1st point, then 2nd point. It doesn't work? The Command line keeps saying: Specify next point or [Close/Undo]. But no lines are getting drawn. i finally have to hit escape to end the line command but no lines have gotten drawn. its the same thing if i draw a square or circle. (Not sure if you need to know this but these are my companies files created by a former employee of my company using our own AutoCad. So, i would think if he's locked this file somehow, i should be able to unlock it.)
I am having a problem this morning. When I started AutoCad LT 2012 and opened my drawing, I can only draw a line in one direction. Also, when i insert a block, all I get is a flat line.
View 3 Replies View Related
