AutoCad :: 2011 - Unable To Plot PDF Files / Job Cancelled
Jul 4, 2011
I am unable to plot PDF files from my AutoCad 2011. Plots OK in Word etc so Windows 7 printer seems ok. Get error message : Job: - Canceled
Job ID: 8
Sheet set name:
Date and time started: 4/07/2011 11:48:32 AM
Date and time completed: 4/07/2011 11:48:33 AM
UserID: user
Profile ID: AutoCAD 2011 Prosteel Ribbon
Total sheets: 1
Sheets plotted: 0
Number of errors: 1
Number of warnings: 0
Sheet: - Canceled
File: D:ProjectsP079 - PDG Engineering for Standard Stacking ConveyorC DrawingsdwgsP079-BMSPR01-0000-SS-DR-0059 to 0066.dwg
Category name:
Page setup:
Device name: Adobe PDF_A3.pc3
Plot file path:
Paper size: A3
MESSAGE: Error : A StartDocPrinter call was not issued.
ERROR: The device has reported an unknown error.
Job: - Canceled
View 3 Replies
ADVERTISEMENT
Sep 1, 2011
AutoCAD Architecture 2011
Windows 7 x64
8GB RAM
Created new PC3 for KIP 3100 plotter using its AutoCAD Heidi driver for Win7x64. Upon plot preview the following error occurs.
This causes a crash report which has been submitted to Autodesk. The response was to install service pack 2. Error still occurs after installing the service pack.
Using the non-AutoCAD driver works.
View 1 Replies
View Related
Jul 20, 2011
I can't plot PDF on AA 2011.
View 3 Replies
View Related
Feb 13, 2013
I am trying to plot a drawing, Visual style: wireframe, occluded edges: dashed. The drawing has millimeters as the unit of measurement. I have tried this (taken from a website some of you might be familiar with):
[URL]
but it does not work. I set the ltscale as low as 0.01 but without result. I tried printing from "model" and "Layout" (everything is set at Wireframe and dashed occluded edges).
I have finished the drawings and documentation and this is holding me back from printing and sending what I have done.
View 9 Replies
View Related
Jan 11, 2012
I'm using AutoCAD 2011 with a Ricoh Aficio W3601 plotter. Occassionally I need to plot out pipe wraps for projects that would be longer than a 36" sheet. Our plotter has a 36" x 150' roll capacity. I have figured out how to define a custom user size paper and get it to show up correctly under the properties button in the plot dialogue box. The print preview is correct, and the plotter cuts the paper off at the correct length, however, the printed portion of the plot is always cut off at 36" or is printed the wrong direction and limited by the roll width. I have tried every combination of landscape/portrait combination without success. I am trying to plot from the model tab using a 1:1 scale.
View 4 Replies
View Related
Aug 21, 2012
Can users with a 64 bit computer share pc3's and pmp's with 32 bit users without adverse effects?
View 1 Replies
View Related
Nov 15, 2010
One to Five people has the same project loaded into their Project Navigator.
One of the people opens a plot sheet while using the Project Navigator.
ALL computers with that project loaded experience an Autocad 2011 Crash.
-No Error Message appears.
-Autocad shuts down completely with no warning.
-Simultaneously!
This only occurs with DWG files located under the Sheets Tab of the project navigator.
It is not Project specific. This has occured for different users in our office with different projects open. However Autocad only crashes for the users with the specific project accessing the plot sheet loaded.
We recently made the switch from 2009 to 2011. So far this is only a problem for projects where the plotsheets were created in 2009. We can't go back to 2009 to plot since the walls etc have now adapted to 2011.
View 6 Replies
View Related
Sep 14, 2012
i lost the media CD of the AutoCAD LT 2011, while i am trying to reinstall the AutoCAD LT software in my laptop unable to do so as the AutoDesk site doesnt have a link to download LT 2011, it has only the LT 2013 now.
where i can download the Lt 2011, i have the serial no and other details with me.
View 1 Replies
View Related
Feb 24, 2011
When I select an object to move I am unable to snap to the grips of the object or any other object close or any intersections. I have double and triple checked my osnap settings. Also, If I select a circle to move I am unable to select the center of the circle through additional osnap settings. One last issue, If I select an object and do a copy with base point command, I am unable to select a definitive base point. No grips or intersections show up.
My co-workers are able to do these functions but I am not.
View 2 Replies
View Related
Mar 31, 2013
AutoCad 2011
I am unable to access the program.
I started using Version 2008, 2009, 2010, 2010 and now 2011. This is the first time I have problems accessing the program.
I get not messages.
View 6 Replies
View Related
Oct 8, 2012
Suddenly, each time that I attempt to plot or print a drawing I get the message "Errors or Warnings Found". I open it up and it shows that the plot has been cancelled. I have run all of the "traps" that I know but to no avail.
View 5 Replies
View Related
Apr 28, 2010
After upgrading to ACA 2011 in plan view I am unable to snap to the edges of walls. Toggling the osnap setting check box to allow object snap to act on wall justification lines seems to have no effect as it always snaps only to the justification line and to nothing else. This is extremely annoying and makes it impossible to dimension to the face of a wall that is center justified. Is this a bug or am I missing some new setting somewhere? All my layers are unfrozen including layer 0.
View 9 Replies
View Related
Aug 16, 2012
I display Preview, then modal form with some options.
One option needs select window but I receive *Cancel* in command line.
If I try to select a window again, everything works OK.
If I disable displaying Preview, it works fine, but function is useless for my purposes
[URL]
I tried Regen, UpdateScreen, etc. after displaying Preview but with no effect.
View 4 Replies
View Related
Jul 30, 2013
I am using inventor 2011 to make an assembly, and No matter wether I sketch off a face or a plane, I cannot get get my sketches to extrude, inventor wants to make cuts when there is nothing to cut. Not sure what I am doing wrong, becasue when I try doing the same thing on a new part it works just fine.
View 3 Replies
View Related
Feb 22, 2013
I have been using LT2000 and LT2006 for years. A few months back we purchased LT2013. It took me a little while to get comfortable with the workspace. Then I found the AutoCad LT Classic option. All was good.
My normal procedure with drawings is to take a screen shot, crop it in paint and paste it to ppt and save that ppt as a pdf. This method allows me to share a small portion of a detailed drawing with customers and vendors for review. I am now to a point with one particular drawing where I would like to plot to PDF. This is something I have never had an issue with using the two previous LT versions. When I go through the motions as I always have before…all I get is a blank page. Preview is blank. I am stuck and can’t seem to figure it out in 2013.
View 5 Replies
View Related
May 15, 2008
I have been making drawings mostly from objects I copy/pasted from objects in previous drawings in my company's database. I had to draw some additions and it is these objects which will not print (everything copy/pasted plots fine).
When I look at the layers window, nothing is out of the ordinary (all layers thawed, unlocked etc).
This is AutoCAD MAP 3D 2009 by the way!
View 6 Replies
View Related
Jan 8, 2013
Unable to plot with AutoCAD Map 3d. Problem just began. Reinstalled program. Installed SP-1. AutoCAD will not plot to ANY device. Previews just fine. Printer icon behaves as if plotting. Stays at that point until plot is cancelled.
View 7 Replies
View Related
Jun 27, 2012
In the early days of Lightroom there was a problem where if you cancelled a edit on a raw file in Photoshop without changing the file (maybe you opened in error) you still ended up with a tiff or PSD file that then needed manual deletion.
This was corrected in later versions. Now however the problem seems to have returned! Am I missing something or is it a screw up by Adobe?
View 1 Replies
View Related
Mar 28, 2011
I am running Windows 7 Professional 64 bit, plotting to HP 4500 DesignJet. If I attempt to plot an oversized map the plotter either spits out a blank page or says it plotted the map and no map prints. We have another machine running Vista 64 bit and Map 3D 2011 and it is able to plot just fine. Another machine is running XP and Map 2008 and can plot fine.
I have updated plotter drivers, settings, and I have tried plotting off several .pc3 configurations all ending with the same result. As of right now when I need to plot large maps I have to send an e transmit to my other machine in order to plot, which just isn't going to work.
View 2 Replies
View Related
Jan 23, 2013
I am new to autocad, I downloaded autocad 2013, When I tried to print/plot it always blank(white), Is there any settings I need to for print/plot?
View 1 Replies
View Related
Sep 4, 2012
I`m using the AutoCad Version 2010 and since last friday I`m not able to Plot PDF datas anymore.It shows the Error "Invalid Window"..But it worked hundreds of times before in the same way.
View 3 Replies
View Related
Mar 18, 2013
Is there any way to import SAT or STP files into AutoCAD LT2011?
View 2 Replies
View Related
Nov 12, 2012
How to import shx and lin files from Autcad LT2011 to version 2013. Each time we upgrade over the years it has been a simple task of saving the 2 files into the program file/autodesk folder however when we try to do this with LT 2013 it doesnt recognise the files. They are from another program called Artisan which uses the Autocad platform. The file extensions are: Artisan.shx and Atrisan.lin.
View 2 Replies
View Related
Apr 25, 2012
I have one workstation running Autocad LT 2007 on a windows 7 32 bit OS, and needs to print to a non plot printer, which is a Kyocera KM-4050 KX. I am unable to print to this printer through Autocad LT 2007 and recieve the following error message . . .
"\ServerNamePrinterName: This plotter configuration conanot be used for one of these reasons: The driver cannot be found, the device can not be found, or the driver has a problem. The None plot device has been substituted."
The Printer works fine with all other applications, and the rest of the users who have Autocad LT 2011 have no issue printing.
I followed the instructions in [URL] ..... and did not see my printer model in the list and was unable to load the driver from a disk.I believe the file it was looking for was .hif, which could not be found.
I also uninstalled and reinstalled the printer driver, and did some testing, so the printer works fine except for this application. According to the user the print function never worked for them in Autocad LT 2007.
View 4 Replies
View Related
Dec 16, 2012
The product is AutoCAD 2013 Architecture. It installed fine. Typically, as part of the install routine, I go in to the Plot dialog and set the plot style table to monochrome.ctb.
However, on this particular install... something is different. When I open the screen, typcially the plot style table is set to 'none' and I then set it to monochrome.ctb. That is not the case on this one. It is defaulting to AEC Standard.stb and monochrome is not in the list.
1.jpg
I read elsewhere to run CONVERTPSTYLES at the command line. I tried that and it did work..however it does not hold the setting. If I close and restart CAD, I am right back to the AEC Standard.stb default again.
This seems to just be a problem with new drawings? If I open one from the network, it does have the monochrome.ctb setting already set.
I assumed it must have been a problem with the default in options, but I believe I have it set correctly? See below.
2.JPG
If I interpret the above correctly, the plot style table drop down box should be defaulting to 'none' ? but it does not... it defaults to AEC Standard.stb.
I have already tried a complete uninstall/Reinstall of CAD and still have the same issue.
View 3 Replies
View Related
Mar 10, 2011
where I can get the Chapter 4 tutorial files for Map 3D 2011. I've looked everywhere for the Creeks.SDF file, but have come up empty handed.
View 2 Replies
View Related
Dec 9, 2013
Our structural firm is using 2011, and our office has received drawings that came out of 2014 twice in the past week (from separate arch clients). In both instances, we back-converted using DWG TrueView 2014, but upon opening in ACAD, none of the walls were showing up (although they do appear in the preview). One of my other drafters dealt with it the first time, and got it resolved, although I didn't get specifics on how. Naturally, the second time it happened, she was out, so I am seeing if the architect can back-save to 2010 on their end and send the file.
While waiting on that, I tried QSelect in the offending file, and in the list of items that comes up, there was, amid the usual Text, Line, Pline, Block, etc., something called ACAD_PROXY_ENTITY. I selected all (nothing was visible, however--usually you see grips at least when you QSelect things), then exploded, and the walls showed up.
I have had somewhat similar odd behavior from drawings coming from I think ADT (do they still make ADT?), where things like walls, doors and windows come in as something block-like (I think AEC OBJECTS?), and we have to explode them in order to control color and visibility of their constituent parts. Perhaps this is something similar?
At any rate, this seems like something that either shouldn't be happening, or that has a more obvious fix than having to qselect and explode invisible things to get them to show up.
View 2 Replies
View Related
Jun 29, 2012
issue I'm having editing some drawings. I have been tasked with editing some drawings that were given to me in .dwg. I can open the files fine in Inventor 2011, but I cannot edit them. Do I need AutoCAD to edit the dwg files?
View 1 Replies
View Related
Dec 19, 2013
Exporting DWG. Files to Stl in 2011 Autocad
View 2 Replies
View Related
Sep 4, 2012
1. I prepared a 57 mm square, proportionally resized it to 58 mm and applied enter for the change but it remained as is i.e. 57 mm sq. Next I made the same changes through property bar, it worked. Through further experiments I observed it only make transformations through enter if we give x=val and move to y=val through tab and press enter. Or if we directly give new value to y and press enter. The property bar doesn't has this problem.
2. Transformations dockers problem of showing wrong position on y-axis. Screen shot attached.
3. Open and Import dialogue boxes don’t get cancelled as we hit ESC key. This problem remains as is from v16.0.0.707.
4. Printing - EPS with CMYK / Native colour management shows graying problem on RIP. Facing it as a major problem.
Problems encountered even after resetting through pressing F8 at startup.
View 2 Replies
View Related
Oct 28, 2011
I am unable to plot lineweight in Mtext while printing the drawing. I have checked the 'Scale Line weight' in Page Setup Manager but the Mtext is not get weighted while other entities gets lineweight when printed with the same options.
View 4 Replies
View Related
