AutoCAD Inventor :: Square To Round Transition Options

Apr 14, 2012

I have a square to round transition that I need formed up and the shop is telling me that they would prefer to split this thing at the corners rather than the flats. I've tried two different ways of doing this but how to handle this part. It's 10.75" OD at the bottom and 2'-4" square at the top and 1'3" in length and made of 1/4" stainless steel plate. The shop wants this in four bent pieces that they can weld together down the corners.

I've tried making just the one side but I'm not getting the results I would like to see. Making the full transition (as in the picture above) gives the finished result I am looking for but I can't separate it into multiple sides.

View 9 Replies

AutoCAD Inventor :: Square To Round Transition - Sheet Metal

Oct 18, 2011

Here I am attaching a square to round transition duct drawings which is weld assembly & assembly drawing in pdf, This one was made in Inventor from one of our principle maker, I am trying to make this similar in inventor as I couldn’t, I am pretty good in sheet metal able to make the casing well, but couldn’t the assembly of pins and making of cladding sheets on that curved surface.

Autodesk Inventor 2010.
Windows XP.

View 9 Replies View Related

AutoCAD Inventor :: Unable To Get Exact Flat Pattern Layout For Round To Square Transition

Nov 4, 2013

I am able to extract an flat pattern (for round to square) but not exactly as the customers drawing.

The original drawing shows some relief in bending lines which i am not able to add in inventor. after a glance at the attachments you will clearly understand what i want.

View 6 Replies View Related

AutoCad 3D :: Solid Square To Round Transition?

Jul 19, 2007

Im a trying to solid model a square to round transition.

View 9 Replies View Related

AutoCad 3D :: Section Of Ductwork Is A Transition From 12x8 Square To 8 Dia Round

Jan 28, 2007

Alright, I'm trying to make a section of ductwork that is a transition from 12x8 square to 8 dia round. I've tried all kinds of methods, but nothing has really gotten me an accurate, realistic model.

View 9 Replies View Related

AutoCAD Inventor :: Weld Round Bar To Square Hollow Section

Mar 22, 2013

I have a solid bar which has a diameter equal to the nternal dimensions of a SHS. I am trying to create a weld, basically to fill the gap with a weld. I tried a similar arrangement with a Circular Hollow Section and it worked perfectly. I have tried fillet and groove for the SHS but it will not accept it.

View 3 Replies View Related

AutoCAD Inventor :: Smoothing Faces Of A Loft (square To Round Shape)

Oct 16, 2013

When I make a loft, from a 12x12 square to an 8" circle (12" high for the sake of arguement), the corners of the square kind of loft up to the circle where it's corners would be...leaving a sharp break between the planes

Is there a way to make it look like the sheet metal lofted flange appears? So that the corners of the square drift to the quadrants of the circle, making a smooth transition?

Inventor 2014
Windows 7 Pro SP1
Intel(R) Core(TM) i7-3770k CPU @ 3.50GHz
16GB RAM
NVIDIA Quadro 4000
3D Connexion SpaceMouse Pro

View 9 Replies View Related

AutoCad 3D :: Solids Taper With Square Base Up To Round Top

May 13, 2010

I'm working on this shape: it has square base, goes to the top round , and round top is shiffted off center.

View 9 Replies View Related

AutoCAD Architecture :: Change Default Square Columns To Round?

Jul 27, 2013

I have modeled a house with some colums supporting a deck. Ideally I would like my colums to be round with a spiral twist.. But would be happy to know how to change the default square into a round colum.

View 1 Replies View Related

GIMP :: How To Round All Square Corners

Aug 5, 2012

Suppose we have a standard QR code composed of hundreds of squares and their hundreds of square corners. (e.g., [URL]......)

How can I get Gimp to round all of the internal and external square corners - let's say to a 10 pixel radius?

View 5 Replies View Related

Photoshop :: Make Round Coner Of Square

Jun 10, 2004

How can round the coners of the square.

View 3 Replies View Related

Photoshop :: Make A Square With Round Corners With Certain Radius

Mar 2, 2013

I would like to make a square with round corners with certain Radius. I use Rectangular Marque Tool with Feathering set to some value. The thing is that when I cut the shape from Layer I don't get a sharp corner but instead I have shaded corner.

View 9 Replies View Related

GIMP :: Round Corners Of A Square Or Rectangle Using Two Functions

Dec 2, 2013

With Gimp you can round the corners of a square or rectangle using two functions: the problem is that doing so all four corners will be rounded, while I am interested in only the two upper corners. Here's an example of what I would do.

View 1 Replies View Related

Paint.NET :: Change Paintbrush Type From Round To Square?

Feb 20, 2013

How do I change the paintbrush type from a round type to a square type, & make it permanent 'till I changed it?

View 5 Replies View Related

Paint.NET :: Design Square Icon With Round Corners?

Mar 15, 2013

I want to design a square icon with round corners. How do I get rid of the little white triangles in the four corners? I tried to design my icon on a transparent square canvas but I still get the little white triangles in the corners!!! And it does not seem possible to resize canvas to "fit" image size...

View 4 Replies View Related

Illustrator :: Create Shape With Round And Square Corners?

Feb 4, 2013

I haven't used illustrator for a while so I'm really stuck on soemthing that should be simple.

I want to create a shape that has round corners on the bottom and square cormers at the top.

I have created two shapes, one with round corners and one with square one.

I was hoping to put them together then use the pathfinder to unite them but this then make the round corner square.

Is it possible to unite shapes with different corners.

View 5 Replies View Related

CorelDRAW X3 :: Crop Image And Make Edges Round Instead Of Square?

Mar 17, 2008

I want to crop an image and make the edges round instead of square. Do I do this with a mask? Can't figure out how to use a mask. I went to Mask Outline->Smooth and it cut the image out and left the round edges.

View 12 Replies View Related

CorelDRAW X6 :: Attract - Repel Tool Missing Sharp And Round Options?

Mar 1, 2013

I watched a tutorial done by AdvancedTshirts.com that showed 2 options for the Attract and Repel drawing tools. The options were in the Property Bar and one was to set the sharp tip option and the other was to set the round tip option. I'm using v6.2 but they are not there when I select either tool.Also, I have to drag very slowly or it doesn't push or pull the edge.

View 2 Replies View Related

Photoshop :: Marquee Tool :: Only Oval Or Square Options Are Available

Jul 4, 2009

i am using photoshop elements and on the marquee tool my only options are square or oval how can i get the other two options for lines?

View 3 Replies View Related

GIMP :: Extend Drawing Border And Change It From Square Outer Border To Round

Nov 11, 2012

I have a drawing that has a white background.

I would like to add more to the white background to make it bigger without having to stretch it and distort the image.

I want to place a circle shaped outline border around the original image with a set border thickness and color and be able to crop/remove the portion of the image beyond the outline, changing it from a square/rectangle image to a circular image.

If I am not able to change the drawing to have a round outer border from square, how can I make the outer parts past the newly created circular outline transparent?

View 6 Replies View Related

AutoCAD Inventor :: How To Smooth Transition Between Two Parts

Apr 12, 2013

I need to do a smooth transtition between that first long cube and the cylinder kind of shpe on it's right so that the cube and cylinder are attached toether and we dont see the edges of the cube.

View 9 Replies View Related

AutoCAD Inventor :: Transition On Cylindrical Backplate

Nov 27, 2013

View 9 Replies View Related

AutoCAD Inventor :: Lofted Surface Transition

May 1, 2012

When creating a loft between two curves, I am not able to control the top and bottom portion of the surface created, I have joined a picture of the part and my IPT file with the problem I got.

View 9 Replies View Related

AutoCAD Inventor :: Put Together Transition Box Assembly - 12N U Joint

Jun 17, 2013

I am trying to put together a transition box assembly but I am in need of a 12N U-Joint. iPart/iAssembly of the u-joint would be even better...then I won't be back looking for the smaller u-joints I am going to need later.

View 2 Replies View Related

AutoCAD Inventor :: Smooth Transition Between Two Pipes?

Apr 12, 2013

See the two pipes connecting at the end on the right side see screen shot 3. How do i make so they look like that in screen shot 3

attachemnt one is the drawing atachment two is the problem that im asking

attackment three is the solution i just don't know how to make it in the actual drawing

View 6 Replies View Related

AutoCAD Visual LISP / AutoLISP :: Diesel Expression - Display Area In Square Feet Not Square Inches?

Feb 16, 2010

How I can update my diesel expression to display the area in square feet not square inches. See expression below.

^C^Cattdia;0;_-insert;AREABLK;1;1;0;$M=$(getvar,AREA);attdia;1

View 9 Replies View Related

AutoCAD Inventor :: Molding Two Features Together / Smooth Transition

Jun 14, 2012

How to mold a pipe and flange together wit a filled in transiton as if they were one continuous piece.

The pipe edge is flush with the flat square fange. The combine option does not allow me to conduct operation.

View 2 Replies View Related

AutoCAD Inventor :: How To Create A Smooth Transition Between Radii

Nov 13, 2012

I am struggling to create a smooth transition between radii called out on a drawing. I am also unsure of how to create a flange on that edge of my part.

Here is the drawing and the model I have created so far.

View 2 Replies View Related

AutoCAD Inventor :: How To Create Lip All Round

Nov 25, 2011

I tried unsuccessfully to create a lip around a curve surface and there is no flat plane to select for the sketch. Wonder if this could be done in Inventor. My version is 2011.

View 4 Replies View Related

AutoCAD Inventor :: Round Parameter Using ILogic?

Sep 20, 2011

how to round a parameter using ilogic.

For example. I have Roperev=Roperev_1. Roperev_1 is determined by an excel equation. I need Roperev to produce a nominal number because this parameter dries a coil revolution and I need the revolution to be a whole number.

I can not just round the excel result because the excel result needs to be multiplied by 2.53 to get the resultant for Roperev_1

View 9 Replies View Related

AutoCAD Inventor :: Extrude Round Stud

May 14, 2013

Right now I am trying to model a concrete embed plate. The design calls for 1/2" round steel embeds at the contour of the line in the attached image. What is the best way to extrude this line into a 1/2" DIA dowel? I have tried the revolve command and sweep command without any luck... I know the sweep command would probably work the best but I can't seem to draw a 1/2" dia circle perpendicular to the line.

View 5 Replies View Related