Is there a way to use the Split Solid tool to partially split a circle and have multiple solids after.
Ex) I would like to cut the tank at the 180 and 270 deg marks. Using the split tool still cuts through 0 and 90. I tried drawing a line from a top view that started from center going through 180, but it still goes through 0 as well.
I've attached an example shell of where I would like to have 6 solids after.
I have a really long parts list and would like to know if there is there a way to split the parts list into two distinct shorter lists.
This is how it is done in Solidworks. Just wondering if splitting BOM's is possible in Inventor.
[URL].......
how to create water flow inside inventor , i have a tank i want to fill with water & water then will flow through a pipe of certain diameter & length
View 1 Replies View RelatedI have an inventor part with the name “0955-P05”. To break it down the Job # is 0955 and the Mark # is P05
The code below will automatically take whatever the file name and split it to fill in the Job # and Mark #
'MarkNumber and Job Information
'Filename Convert
Part_Number = iProperties.Value("Project", "Part Number")
iProperties.Value("Custom", "Job" ) = "=" & Left(Part_Number,4)
iProperties.Value("Custom", "MarkNumber") = "=" & Right(Part_Number,3)
The code works great in till my Mark # reaches P99
I know what you’re thinking but I can’t change the Mark #s to P001 and fix the code that way. The whole company is already set up with this Mark # system and they will not change it.
I need to shell out a Loft in the attached IV 2012 part file.The Loft i tried also as a new solid but the shell also cuts into the cylinder ( revolution 1 ) . I only want the 2 sides and bottom of the Loft to be Shelled, not the cylinder. What do i need to change to get the shell to work?
View 4 Replies View RelatedI am creating three shapes out of a pyramid. I figure if I split the pyramid in half, I can create two, then mirror them and blend the two together to make the final design. I have figured out how to create a pyramid by extruding a cube with a taper.
My pyramid is 40mm x 40mm x 40mm. I need to cut it in half, diagonally, top to bottom.
When I have the pyramid in the workspace, I see nothing that I can select - that will allow me to create lines where I need to - to cut them out.
I'll add a logo in 3-d that I am trying to create. (also, I am using this project to familiarize myself with the software.)
Is it possible to fill a shell with sand? The end use of my design will have sand - like in a childs plasitc basketball hoop/stand assembly and I would like to try to approximate the center of gravity and other useful info.
ACAD 2010
ACADE 2008
AIS 2009
Whats the importance of "Shell Connector Tolerance"in the create new simulation dialog box. Any example or some kind of illustration to explain this.
C1
Inventor Professional 2013
Vault Collaboration 2013
When trying to shell a part i get the error: the attempted shell operation was unable to solve for a vertex....etc. i have attached the problem part file, of which the drawing is a fairly complicated frame (a chassis concept for a 3 wheeled race car i am designing)
How the part was made:It was created in an assembly using the frame generator tool and then converted to part file using the shrinkwrap feature. When using the shrinkwrap command, i selected: single solid body merging out seams between planar faces, All hole patching, break link, and remove all internal voids. and then when trying to shell i get the error message when selecting a wall thickness of 2mm.
i cant understand why the shell feature does not work as i have successfully shelled a very similar part file (with only slight differences in geometry from the file attached in the same way as what i am trying to do with this part). i can provide this part file upon request or the assembly file from which either was created. i need to shell the component in this way so that i can run accurate FEA (stress analysis) for crash simulations on it
I am using inventor 2013 (64bit OS)
I am trying to make a shell of a mesh feature after I have upscaled it.
I do not think the regular shell technique will work as my mesh feature has hundreds of surfaces. So, I decided to open the file with my part in it and then derive the same part but a little bigger using the derive button. I would then subtract out the smaller, original, one to make a shell of the bigger, derived one.
Unfortunately, when I use this method to upscale, the 2 objects are not concentric so I cannot make the uniform shell that I want to.
I have attached the file of my mesh feature in case you want to see it. not that you will have to convert the object you see on my file into a base feature before doing anything with it. I did not because it would have made the file to big to attach.
I have a funnel with a curved top. I'm trying to project an inset of the border onto the curved surface and use the shell command to create a hollow funnel with an overhanging lip. I have projected the inset successfully, but cannot select the resulting smaller face, just the whole original face.
A similar problem that I tried while attempting to figure this out was shelling a sphere. 2d sketch -> 3d sketch project onto surface, and try applying shell to the resulting "face". However I can only select the whole face when trying to shell.
This shape will not shell out with a 3mm thickness.....i suspect i may have not modelled correctly....how would you model this shape part so as it can be shelled out?
View 8 Replies View RelatedWhat I'm doing is preparing a model for FEA, and I want to split some faces for where the nuts meet a surface. So far I've only been able to do this by repeatedly making a sketch and then splitting around each hole. Is it possible to do several splits from one drawing or to pattern the split? (I've attempted both, but failed hard).
Splitting a surface 5 times is slow, but essentially fine. Doing it this way when I have more bolt holes though is a chore.
I can split a part into 2 solid entities, I now want to rotate one of these entities with it's features say 30 degrees or whatever and then rejoin them as a newly shaped part.
I think all this is possible apart from rotating the split solid after splitting?
how can I rotate my split solid?
How can i shell out the part with 2mm thickness walls?
View 1 Replies View RelatedUsing the shell feature. I have used a bit in the past and its always done what I want. This go around what I want is to shell without removing any outside walls, which it does no matter I seem to try. I can easily add a new outter wall back in, but if I can shell without removing an outter wall it would be just that much cleaner in my tree.
View 5 Replies View RelatedI would like to be able to the share external geometry of a fully assembled mechanical model without surrendering any part or assembly data. Is there a way to turn this assembly into an external surface "shell"…?
View 1 Replies View RelatedHow to create a oval shape.The attached file shows the shape i need.How do i make the shape and then shell out 2mm.
View 2 Replies View RelatedI am trying to shell out the underside handle of the feature. I have attached my part file along with the assignment briefing file. It is the second part on the page, i.e. the Garlic Press Handle.
View 2 Replies View RelatedSee Shell 2 .. it shells out but how do i have the Shell to the curved face on Revolution 1.I want the Shell to cut through Extrusion 1 and to the Revolution 1 curved face.
View 9 Replies View RelatedI have a blade housing that requires a continuos radius around the profile. It is not a full radius. When I shell the blade, it looks like the raidius wants to continue. I was told I had to use two fillets and the particial radius will not work. However, the continuous radious in the customers requirement. Is there a way to shell this part correctly?
View 2 Replies View RelatedThe problem: a complex curvy part will shell 0.5 mm but not 3mm - some of the surfaces fall inside the others.
A work around : Offset each surace (individually - not quilt) then stich & sculpt.
A program: To offset an enclosed surface, individual face by face, internally. Then manually stich to identify any errors & patch accordingly.
Note these parts have 100's of faces so the code would be useful - not sure how to always offset the surface to the inside of the volume.
I'm trying to create a model of a Golf club head. I need it to be hollow but I am unable to do this using the shell operation or by creating a surface and thickening the faces. I created the geometry by lofting a series of sketches. I think the nature of the geometry may be causing the problem.
View 1 Replies View RelatedI'm not exactly sure how to verbalize this task, but I'd like to shell a solid by selecting 2 opposing faces amd maintain a center wall. Can this be done using only the shell feature?
Notice the solid below is hollow.
I am having trouble shelling a part I have designed. Every time I try, with no matter what thickness, I get the following message:
"The attempted shell operation had non-manifold inputs. Try with manifold inputs."
Having problem with a particular file crash/freeze/not respond whenever using the shell feature on Inventor LT 2013? I am operating with Windows 7. I have the AutoCAD Inventor LT 2013 Suite. Just bought the computer two weeks ago and just installed Inventor about two weeks ago also.
In any case, it seems the file of this model is corrupted, as I have never had a problem using the Shell feature before this and shelling other objects even while the corrupted part is open works fine. However, if the "visibilty" of the part in question is checked and i click on the shell button, the program immediately freezes. I am not sure how to work around this and I really do not want to start the entire part modeling over from scratch.
Working with... Autodesk: AutoCAD Inventor LT Suite 2013 | OS: Windows 7 | GC: ATI 6670 | Mem: 8 gigs RAM | Proc: Intel core i5 | Monitor: Acer V213HL
I'm trying to create a solid using the inside geometry of a shell in Inventor 2011. is there a simple way of doing this? i have attached the part i'm working on and need a solid that represents the free space inside the shell.
View 2 Replies View RelatedI have drawn an assembly of parts and now wish to line up the small hole in the large shell to the projecting pipe,i thought it would be a simple task of using mates (insert aligned) but this does not let me pick on the boundary of the small hole.
View 3 Replies View RelatedFor a while now, I've been trying to shell a split game controller that will create the bottom part of the casing. However, every time I try to shell, a problem occurs "Modelling failure in ASM. Redefine inputs".
I've tried to find the source of the problem through supressing features, and when it finally does shell, the casing creates another problem that will not allow me to loft to get the proper appearance.
I am using AutoCAD 2012 and I noticed that the dish/dome command is gone. How do I make a dish?
View 9 Replies View RelatedI have to design 35m dia panel tank (water storage), the shell, roof all design i done. How to design foundation of tank?.
View 9 Replies View Related