See Shell 2 .. it shells out but how do i have the Shell to the curved face on Revolution 1.I want the Shell to cut through Extrusion 1 and to the Revolution 1 curved face.
View 9 RepliesThere is any option to merge bottom face of pad eye and pipe curved face... Something like
1. Extrude face to a surface or
2. like notch option available in frame generator ?
N:B - pad eye is made by extrusion and pipe made by frame generator.
Is it possible to extend the curved face of the solid, straight up to the new not curved face. It need to be a solid .
View 3 Replies View RelatedI am trying to pinpoint the center of gravity on a curved face of an assembly. I can use the c og G command to get the true center of gravity but i would like to incorporate lifting eyes into the finished assembly. Basically I need to know how to find the C of G on a given surface. I have attached the assembly I am working on and added lifting eyes roughly where I would like them. I have tried measuring from the C of G to a face and then creating the lug above the C of G but somehow it doesn't line up.
View 7 Replies View RelatedWhen trying to use the 3D shell command, I receive "Face loops not repairable" error. Why I get this error?
View 1 Replies View RelatedI've assembled a bolt and a slide block that is constrained to a base plate and am able to put everything in motion. I have the slide block constrained to slide the distance of the base plate and when I reach the end the bolt continues to rotate when, if this was a real part, should stop. How can I get this bolt to stop once the slide block reaches its ending constraint?
View 2 Replies View RelatedI am having trouble trying to get the Loft-1 to run the same shape as Revolution-2 .Picture 1-1 shows how Loft-1 is slightly off centre to Revolution-2 at the top .could i model the Loft-1 and Revolution-2 using different tools in one command making it a smooth shape. Another problem i have is how do i make Revolution-2 at the end terminate into Revolution-1 smoothly.I tried using Loft but it kept getting fail message.Picture 1-2 shows where to terminate the end into the Revolution-1 body.
Inventor 2012
I am trying to insert a revolution joint into my assembly but it seems it does not exist. I have attached two screenshots. One is from a tutorial I am going through which contains a longer list of available joints. (More.png) The other is the assembly I am working on which contains less available joints. (Less.png)
View 1 Replies View RelatedI'm having trouble with a tangent constraint. I have an adaptive part in an assembly and it is a revolution. I am able to constrain the top and bottom of the part so that it expands and contracts with my assembly. But, when I go to constrain the sides of my part via the tangent constraint I get an "inconsistent constraint" error.
View 6 Replies View RelatedI want to extrude a big number of pillars to a rather complicated surface and that works out fine. But each end of the pillars warps around the surface and I want them just to go up to it and stop with a resulting horizontal face.
View 1 Replies View RelatedAll I need to do is merge a circular face to a flat face, so both faces become one continuous face. Is this possible at all?
I have a attached a screenshot to show what I mean. Face 1 needs to be merged with face 2. This is so if I constrain anything to that face it will constrain to the entire face and not either the circular face OR the flat face.
I need to shell out a Loft in the attached IV 2012 part file.The Loft i tried also as a new solid but the shell also cuts into the cylinder ( revolution 1 ) . I only want the 2 sides and bottom of the Loft to be Shelled, not the cylinder. What do i need to change to get the shell to work?
View 4 Replies View RelatedIs it possible to fill a shell with sand? The end use of my design will have sand - like in a childs plasitc basketball hoop/stand assembly and I would like to try to approximate the center of gravity and other useful info.
ACAD 2010
ACADE 2008
AIS 2009
Whats the importance of "Shell Connector Tolerance"in the create new simulation dialog box. Any example or some kind of illustration to explain this.
C1
Inventor Professional 2013
Vault Collaboration 2013
When trying to shell a part i get the error: the attempted shell operation was unable to solve for a vertex....etc. i have attached the problem part file, of which the drawing is a fairly complicated frame (a chassis concept for a 3 wheeled race car i am designing)
How the part was made:It was created in an assembly using the frame generator tool and then converted to part file using the shrinkwrap feature. When using the shrinkwrap command, i selected: single solid body merging out seams between planar faces, All hole patching, break link, and remove all internal voids. and then when trying to shell i get the error message when selecting a wall thickness of 2mm.
i cant understand why the shell feature does not work as i have successfully shelled a very similar part file (with only slight differences in geometry from the file attached in the same way as what i am trying to do with this part). i can provide this part file upon request or the assembly file from which either was created. i need to shell the component in this way so that i can run accurate FEA (stress analysis) for crash simulations on it
I am using inventor 2013 (64bit OS)
I am trying to make a shell of a mesh feature after I have upscaled it.
I do not think the regular shell technique will work as my mesh feature has hundreds of surfaces. So, I decided to open the file with my part in it and then derive the same part but a little bigger using the derive button. I would then subtract out the smaller, original, one to make a shell of the bigger, derived one.
Unfortunately, when I use this method to upscale, the 2 objects are not concentric so I cannot make the uniform shell that I want to.
I have attached the file of my mesh feature in case you want to see it. not that you will have to convert the object you see on my file into a base feature before doing anything with it. I did not because it would have made the file to big to attach.
I have a funnel with a curved top. I'm trying to project an inset of the border onto the curved surface and use the shell command to create a hollow funnel with an overhanging lip. I have projected the inset successfully, but cannot select the resulting smaller face, just the whole original face.
A similar problem that I tried while attempting to figure this out was shelling a sphere. 2d sketch -> 3d sketch project onto surface, and try applying shell to the resulting "face". However I can only select the whole face when trying to shell.
This shape will not shell out with a 3mm thickness.....i suspect i may have not modelled correctly....how would you model this shape part so as it can be shelled out?
View 8 Replies View RelatedHow can i shell out the part with 2mm thickness walls?
View 1 Replies View RelatedIs there a way to use the Split Solid tool to partially split a circle and have multiple solids after.
Ex) I would like to cut the tank at the 180 and 270 deg marks. Using the split tool still cuts through 0 and 90. I tried drawing a line from a top view that started from center going through 180, but it still goes through 0 as well.
I've attached an example shell of where I would like to have 6 solids after.
Using the shell feature. I have used a bit in the past and its always done what I want. This go around what I want is to shell without removing any outside walls, which it does no matter I seem to try. I can easily add a new outter wall back in, but if I can shell without removing an outter wall it would be just that much cleaner in my tree.
View 5 Replies View RelatedI would like to be able to the share external geometry of a fully assembled mechanical model without surrendering any part or assembly data. Is there a way to turn this assembly into an external surface "shell"…?
View 1 Replies View RelatedHow to create a oval shape.The attached file shows the shape i need.How do i make the shape and then shell out 2mm.
View 2 Replies View RelatedI am trying to shell out the underside handle of the feature. I have attached my part file along with the assignment briefing file. It is the second part on the page, i.e. the Garlic Press Handle.
View 2 Replies View RelatedI've been playing around with autocad rendering, I have the bowl which is revolution of a profile but it is 'ruled' looking. I changed the options in preferences to some higher numbers and regenall and everything smoothed out but the bowl. is there another setting somewhere for this? Also the spacers on the table are chrome, but are not showing the material.
View 9 Replies View RelatedI have a blade housing that requires a continuos radius around the profile. It is not a full radius. When I shell the blade, it looks like the raidius wants to continue. I was told I had to use two fillets and the particial radius will not work. However, the continuous radious in the customers requirement. Is there a way to shell this part correctly?
View 2 Replies View RelatedThe problem: a complex curvy part will shell 0.5 mm but not 3mm - some of the surfaces fall inside the others.
A work around : Offset each surace (individually - not quilt) then stich & sculpt.
A program: To offset an enclosed surface, individual face by face, internally. Then manually stich to identify any errors & patch accordingly.
Note these parts have 100's of faces so the code would be useful - not sure how to always offset the surface to the inside of the volume.
I'm trying to create a model of a Golf club head. I need it to be hollow but I am unable to do this using the shell operation or by creating a surface and thickening the faces. I created the geometry by lofting a series of sketches. I think the nature of the geometry may be causing the problem.
View 1 Replies View RelatedI'm not exactly sure how to verbalize this task, but I'd like to shell a solid by selecting 2 opposing faces amd maintain a center wall. Can this be done using only the shell feature?
Notice the solid below is hollow.
I am having trouble shelling a part I have designed. Every time I try, with no matter what thickness, I get the following message:
"The attempted shell operation had non-manifold inputs. Try with manifold inputs."
Having problem with a particular file crash/freeze/not respond whenever using the shell feature on Inventor LT 2013? I am operating with Windows 7. I have the AutoCAD Inventor LT 2013 Suite. Just bought the computer two weeks ago and just installed Inventor about two weeks ago also.
In any case, it seems the file of this model is corrupted, as I have never had a problem using the Shell feature before this and shelling other objects even while the corrupted part is open works fine. However, if the "visibilty" of the part in question is checked and i click on the shell button, the program immediately freezes. I am not sure how to work around this and I really do not want to start the entire part modeling over from scratch.
Working with... Autodesk: AutoCAD Inventor LT Suite 2013 | OS: Windows 7 | GC: ATI 6670 | Mem: 8 gigs RAM | Proc: Intel core i5 | Monitor: Acer V213HL