There is any option to merge bottom face of pad eye and pipe curved face... Something like
1. Extrude face to a surface or
2. like notch option available in frame generator ?
N:B - pad eye is made by extrusion and pipe made by frame generator.
Is it possible to extend the curved face of the solid, straight up to the new not curved face. It need to be a solid .
View 3 Replies View RelatedSee Shell 2 .. it shells out but how do i have the Shell to the curved face on Revolution 1.I want the Shell to cut through Extrusion 1 and to the Revolution 1 curved face.
View 9 Replies View RelatedI am trying to pinpoint the center of gravity on a curved face of an assembly. I can use the c og G command to get the true center of gravity but i would like to incorporate lifting eyes into the finished assembly. Basically I need to know how to find the C of G on a given surface. I have attached the assembly I am working on and added lifting eyes roughly where I would like them. I have tried measuring from the C of G to a face and then creating the lug above the C of G but somehow it doesn't line up.
View 7 Replies View RelatedAll I need to do is merge a circular face to a flat face, so both faces become one continuous face. Is this possible at all?
I have a attached a screenshot to show what I mean. Face 1 needs to be merged with face 2. This is so if I constrain anything to that face it will constrain to the entire face and not either the circular face OR the flat face.
how to edit a solid with opening a hole only one face and deleting an another face..
I added a drawing file which has a coloured face solid,I put a circle on blue face and making a hole on this face,and I want to delete red face without exploding solid,after all this I want to mesh this solid with maximum 25 units.
Is there a way to use PRESSPULL on a face that's behind or underneath another face. When I use PRESSPULL it always selects the face on top and sometimes I want a face that is behind or underneath that face.
View 3 Replies View Relatedwhen I anchor the layer face over the background face the floating selection disappears which means I cannot work on the layer face and therfore am unable to erase the layer face into the background face,this is on gimp 2.6
View 4 Replies View Relatedhow to put someones face onto another persons face.
View 3 Replies View Relatedcreat roof with same line on top roof face & roof vertical side face?
View 2 Replies View RelatedIn Inventor 2013 when i export face as it is automaticly exported to DWG 2013 version. How to i set it to 2010 version export without having to do it everytime manually? (option then chooose 2010)
View 2 Replies View RelatedI am trying to CAD a model rocket I just made so I can test the aerodynamics of it. I have all of the individual parts made in inventor, but I am having trouble getting the fins on the rocket.
How can I constrain the fins (which have a flat face) to the outside of the cylindrical rocket tube? The photo shows the fin and the face (the narrow and long face) that I am trying to constrain to the tube.
I am trying to put a 1 degree draft on the face shaded in yellow in the direction I have shown....not sure how to accomplish this?
View 4 Replies View RelatedI can add sketch on a part's workplane (xy, xz, yz) by using sketchs.add.is there anyway i can select a face of part and create a new sketch?
View 6 Replies View RelatedI'm trying to model plug welds in IV2014. I've read all the posts here that say that I need to split the hole faces. Problem is, the split face command doesn't seem to appear in weldments. I want to make the holes to be plugged as a weld preparation. Am I just missing something here, or is IV so backward that a common weld can only be achieved when not working with a weldment?
Inventor Pro 2014 SP1
HP Z400 Workstation
Intel Xeon W3565 @ 3.20GHz
12Gb RAM
Win 7 64 Pro SP1
Spacepilot Pro v3.17.4
I have a script which saves the flat pattern from a sheet metal part as a dxf file. But we also have standard part files that we save a face as a flat pattern. So I'm looking to be able to select a face then run a script to save the selected face as a flat pattern in a dxf file.
View 1 Replies View RelatedIn doing a move face I noticed there isn't any parameters that can be edited after the move face has been created. I want to control the face length with a parameter after it has been created. Am I missing something or is there a work-a-round?
View 2 Replies View RelatedI need to find a way to export the selected face to dwg and to have the Part Number and if possible the description written under the exported face. I don't know if it's possible to do this. I know it's possible to export programmatically the selected face, but is it possible to get the name + description into the drawing too?
We're just looking for a way to "automate" the creation of our laser drawings.
Having never used this command before I am struggling as to where it is located.I imported a U-Bolt in Solidworks format and I am just trying to move the nuts as indicated.
View 5 Replies View RelatedTrying to add draft to an area on this part. Not sure exactly how to get the results I'm looking for. Tried "Draft" command and that didnt work at all. Tried to do a sweep. Its close, but not exacly what I want.
I am trying to get draft applied on this entire face at a given angle (say 5°). The Sweep feature in the part is where I attempted it, but you can see below the Ø6in section, all of the face does not have the draft on it.
I have a face plate with strokes on it to represent pressure increments.I cannot get the numbers onto the face plate.On the large stroke it starts at 0 and goes to 9 .. How do i add the numbers. Also i used extrusions for the increment strokes with circular patterns and mirror features.Is this how it should be modeled?
2013 EDU
How can I add a material thickness to a face trimmed from IGES file?
I have a surface imported from IGES file, then trimmed to a single face in IV that I would like to materialize.
I tried times for thickness, but IV doesn't like it.
Neither can I apply Shell for part, nor thickness adding from Sheet metal.
It is a 3D Lofted surface, very simple single one.
i have two pictures. i want to take the face of one picture and put it on the face of the 2nd picture
View 1 Replies View RelatedI'm trying to notch a curved pipe with another pipe and its giving me many problems because I can't select it. What can I do to work it out?
View 9 Replies View RelatedHow can i get the length or diameter of a cylindrical face by selecting the face as shown in the attached picture.
View 4 Replies View RelatedI'm trying to apply a Knurled Face appearance to a bar the color will change from the current yellow to a polished steel but either the diamond patter is to fine or not there at all. I've be into the Appearance setting moved the sliders back and forward the preview image changes but NOT the actual appearance on the bar itself.
View 1 Replies View RelatedI need to be able to pick a face on a part in an assembly inside a iLogic rule. How can I set up the events to suspend the code to have the user pick the face?
View 6 Replies View RelatedI am working on a project were I need to select a face and create a workplane out of such face, see the figure attach. my language of choice is C#.
Here is what I think it should be done, my proble is that the oWork (the workplane I just created remains null) and the whole project crashes.
private Inventor.Application mApp = null;.....if (((mApp.ActiveDocument != null))){
if ((mApp.ActiveDocument.DocumentType == DocumentTypeEnum.kPartDocumentObject)){
PartComponentDefinition oPartCom = mApp.ActiveDocument as PartComponentDefinition;
PartDocument oDoc = mApp.ActiveDocument as PartDocument;if ((oDoc.SelectSet[1]) is Face){
System.Windows.Forms.MessageBox.Show("You just selected a surface", "Surface Evaluator");Face oFace = oDoc.SelectSet[1] as Face;
WorkPlane oWorkpl = oFace as WorkPlane;
PlanarSketch oSketch = oDoc.ComponentDefinition.Sketches.Add(oWorkpl, false);
//WHAT AM I DOING WRONG?
}}}
What I'm doing is preparing a model for FEA, and I want to split some faces for where the nuts meet a surface. So far I've only been able to do this by repeatedly making a sketch and then splitting around each hole. Is it possible to do several splits from one drawing or to pattern the split? (I've attempted both, but failed hard).
Splitting a surface 5 times is slow, but essentially fine. Doing it this way when I have more bolt holes though is a chore.
I have a .Sat file I've brought into Inventor. The problem is that, as you can see from the attached zebra analysis, the faces are smooth and flush but I still have several unnecessary isolines. How can I get rid of them and I don't mean changing the view to have lines off I mean actually sealing the faces such that they erase the seam.
View 5 Replies View RelatedI'm working with Autodesk Inventor 2009. I have several parts colored in gray, black and red.
The grey color is the basic part color/material.The black color is feature color styles.The red color is face color styles. I need to change all the face color styles (red) to the original part color/material (gray/default). I can do this by right-clicking on a surface > properties > face properties.
My problem is that I have a lot of surfaces (mostly due to fillets). I can choose multiple ones with ctrl + click, but even that would take forever.
Is there an easier way to change all the face colors at once?
