What is the best setting for shrink wrapping an assembly?
I've found shrink wrapping it as a surface causes problems with the video card when rotating the model and placing views on a drawing.
I am working in an Inventor Assembly .iam, I have about 250 fasteners (screws) that are constrained to a flat washer and lock washer. I would like to put them in as a single unit (sub assembly if you will) and then promote or explode them in the top level so that my bom has 250 screws, 250 washers, and 250 lock washers all at the same level, not associated to one another except thru the constraints that were entered in the original assembly. I have tried Promote but that doesn't work because it removes the washers from the original file and I end up with only 1 instance of the assembly. Am I approaching this incorrectly? Is there a better way? I run across this scenario with different components quite often.
View 2 Replies View RelatedIf you have created a sub assembly and inserted it into an upper level assemby, is there a way to bust up the sub assembly at that level?
The issue arising is the individual components need to be called out on the upper level, but in the drawing are all showing up as the same balloon.
i have a valve vault assembly that i am creating that has two headers running through a large cylinder vault. how i get a total BOM if i were to create the header assembly file separate from the the total vault assembly file. is there a way to explode the header assembly bom when i do the drawing.
View 1 Replies View RelatedWhy does the table wrap like this (see attached)?? Shouldn't it place the wrapped rows on the bottom?
View 6 Replies View RelatedI'm attempting to use the "emboss" feature and wrapping the text to the surface of the part.
Attached is the example of the part I am working with. Also attached is the error message I receive after attempting the process. Is there another way to wrap the text about the surface of a "coiled" face?
I have a part that I want to have made by rapid prototyping that will in turn be used as a pattern for casting alloy metal parts. I need to apply a factor to the part to compensate for the shrinkage that occurs when a metal part is poured in a molten stage and will cool to slightly smalller dimensions than the mold. Is there an easy way to do this without having to recreate the part to slightly larger dimensions?
View 2 Replies View RelatedI have a part that was sent to me from a vendor. It was a large 80MB part so I put it in an assembly file and shrinkwrapped it to reduce the size of it. Now it is transparent and I can not figure out how to turn it off.
View 8 Replies View RelatedI have a part which is lets say 10ft long. Now I need to modify that to be 9.5ft. Is there a simple way to remove that .5ft from the center of the part?
I just need a way to cut out a .5ft section in the middle and then put the two remaining pieces back together. Doing this would be much easier than editing the sketches for the part, especially since I may have to change the amount that is cut out and that would change the number of holes and features.
Attached is a picture of the parts i have to edit and some lines to show the section that needs to get removed.
I've been attempting to create a sphere with an Earth texture, for which I've made a custom appearance with a flattened picture of earth. Instead of wrapping to the sphere, however, the image is mirrored on both sides of the sphere and extremely distorted. I knew wrapping 2D geometry to a sphere was not strictly possible, but is there no way to pull it off with an image?
If not, would something like this be possible in 3DS max?
how to Wrap the text shown here. Obviously the Column labeled "ITEM NO." would be 1, 2 , 3 etc. So I would like that column to be smaller. When I make the column smaller, the wording disappears.
View 1 Replies View RelatedWhen a parts list in an Inventor drawing is wrapped it always takes the bottom portion and kicks it to the left.
Is there a way to kick it to the right? So when you are looking at the BOM it reads such that item 1 is in the first group and not the second.
What is the purpose of creating/using shrink wrap substitutes? I thought that it reduces the file size, but noticed that some files turn to be larger after shrink wrapping it. ?
View 6 Replies View RelatedI am a tech illustrator taking our engineering models and creating dumb solids for architects to drop into CAD drawings. When I take an assembly and try to shrinkwrap it (with the Solid Bodies option) the file still has all the internal ribs and fillets and stand-outs. I have created extrudes to fill gaps and holes and even tried to create single pieces to assemble later to no avail.
View 3 Replies View RelatedHaving trouble Wrapping projected curve to a surface of a cylindrical solid to make a barrel cam,
View 2 Replies View RelatedI need to create shrink wrap on Bunch of files. I would like to create a programme.
let me know the code to proceed for Programme.
About Substitute Shrink wrap parts, it doesn't automatic update when I use UPDATE or even REBUILD ALL inside the LOD with it, even if I don't break the link with the assembly it doesn't update, so I have to go in each assembly with Substitute parts ( with are many in huge projects) and then verify with "Check for updates" in the correct LOD (which in some cases are more than one per assembly). Is there a way to update them direct from the main assembly with rebuild all or something like that ?
View 1 Replies View RelatedI'm trying to use assemblies when creating a corridor. The Tool Pallette is emply but I can drag the assembiles in from the Catalog. I've also created an assembly using the ASC. Neither work when I try to use them. The error message is attached.
I'm using a network installation and I do not have the option of changing it to a DVD installation.
I have 2 tanks, each one is an assembly in itself, and they have to be positioned on a steel skid, also an assembly and then interconnecting pipework between the two. My prioblem is that I can't seem to find a way to position the two tanks at a set distance from each other and in relation to the edges of the skid.
Because of this, my pipe router is going all over the place in trying to join up the two termination points.
Will the next release of Inventor have the capability to perform FEA on bolted assemblies?
View 9 Replies View RelatedIn SW I was able to create assemblies that had components with limited motion and then set them as "Fllexable" and allow them to move in larger assemblies. How do I do this in Inventor? I have a trailer with both the front and rear axles able to pivot. These axle sub-assemblies are both able to pivot as top level assemblies but when they are assembled in the trailer assembly the only way I have found to allow movement is to make one axle active and move it then activate the other nad move it. This doesn't work well if there are several interdependant subassemblies that should move together. I am in Inventor 2012.
Inventor Premium 2013 SP1.1
Vault 2013- plain vanilla version
HP G71 notebook
celeron cpu w 4gb RAM and 64 bit system
Win 7 home premium
I use hinges in my door assemblies and they are basically placed into the assembly each time and become flexible so the doors can operate. The hinges are one size and don't change in any way or shape. What is the best practice for inserting these hinges into my door assemblies?
Inventor 2013
Windows 7 Professional 64-bit SP1
HP EliteBook 8470w
Processor: Intel(R) Core(TM) i7-3610QM CPU @ 2.30GHz
Memory: 16 GB
AMD FirePro M2000
3D Connexion SpacePilot
I have converted a lot of STEP files to .iam files. What is the easiest way to put them in a library? there is realy no need to publish them is them, i already have them in subfolders etc.
View 6 Replies View RelatedWe have some structure issues going on. Below is an example of our current structure.
1. Overall Frame Assy
2. Frame Weldment
3. Spine Weldment
3. Bracket Assy
4. Deck Brackets
4. Air Brackets
4. Hyd Brackets
The biggest problem is we have all of these level 3 and 4 subassemblies that need to reference upper level assemblies to show placement on the drawings. We have tried utilizing LOD's and view reps but still can't fix the problem. The problem comes into play when we get to upper level assemblies that become so huge because of all of the references that are happening at lower levels. It is structured this way to create small BOM's and to be able to use in multiple different structures without having to pull a new Part Number.
We need the reference geometry to be able to show on the drawing our locations of all of these lower level assemblies and how they mount to the frame in their respected locations.
I'm trying to change the BOM structure of some sub-assemblies from "Normal" to "Phantom". However, some are displayed as disabled and therefore do not allow any changes/overrides. How can I enable these in the BOM?
Inventor RS 2011
AutoCAD Mechanical 2011
ASD 2013
Vault Collaboration 2011
Windows 7 Pro
This is using Inventor 2013 Professional.
I've created a simple iPart and want to insert multiple instances of it into an assembly. The plan is to use a parameter-driven iPart to create multiple variations on the same basic model which will eventually be lasercut.
I've included a sample archive. 2DiPart is a simple part with a couple parameters. 2Dassembly is where I've tried to include this part. I'm able to walk through all the dialogs to place the iPart, and will even see it in the canvas as I select the insertion point. However, after I dismiss the dialog, nothing shows up in the canvas. I'm still able to see the component instances in the project explorer however.
How to best to get multiple instances of a parametric iPart into a drawing that can be lasercut.
I'm having a problem highlighting parts within a sub assembly. A simple structure to demonstarte this issue would be:
TopLevel.iam
|
SubAssy.iam
|
ChildPart1.ipt
ChildPart2.ipt
Using this structure I wish to highligh ChildPart1.ipt, howver my vba macro code below doesn't seem to work (nothing happens):
Public Sub Highlight()
Dim SubAssy As Inventor.AssemblyDocument
Dim ChildPart1 As Inventor.ComponentOccurrence
[Code].....
I have assembly with over 100 sub assemblies. I need to export the COG for each sub assembly to excel. The COG must be in relation to the parent assembly's origin point.
I can get coordinates manualy (right click on sub assembly - iProperties-Phisical), but it is take a lots of time.
Autodesk Inventor Professional 2013
Windows 7 64-bit
Is there any easy way to turn off visibility for all datum planes when opening a Pro/E assembly in Inventor 2010? It is incredibly time-consuming, not to mention irritating, to click through and hide them all.
View 3 Replies View RelatedI'm trying to take multiple parts of the same type and make them into one .ipt I began doing this and It seemed to be working fine. When I put those grouped .ipts into an .iam, Inventor creates a Subfolder of each .ipt and fills it with each part from that group and now those created ipts are unique unlinked parts (unlinked to the group ipt). I'm trying to reduce our file count and link our .ipts and .idws/.dwgs so this Inventor file creator results in the opposite of what I'm looking for. My question now is is there any way to modify this process to work the way I need it to or is there a completely different way that I should be doing this?
View 4 Replies View RelatedHow do you limit translation/rotation of components in Assembly mode? I'm volunteering as a teacher to some high school students and we're modeling a robotic arm using syringes as prime movers. I want to keep the linkages from traveling inside-out and limit the travel of the syringe plunger.
View 9 Replies View Related