I wish to delete all project geometry in the active drawingsketch with 1 click
But unsure how to get to these constraints.
Are these geometricConstraints?
What I have now doesnt work:
Select Case ThisDoc.Document.DocumentType
Case 12292:
Case Else: MsgBox("Current Document not a drawing document")
Exit Sub
End Select
[Code] .......
I have an existing sketch and a new sketch onto which I want to project some lines from the existing sketch.
The panes of both sketches do not run parrallel.
Normally a projection is created by imaginary projection lines from the existing sketch to the new sketch perpendicular to the new sketch.
But now and want to project the existing sketch with imaginary projection lines that are perpendicular to the existing sketch.
Is there a way to hide project geometry from model sketch? I am modeling a sheetmetal part where I need to sketch centermaks, part number etc. for laser cutting. I want to use xy planes for symmetry reasons when sketching, but I don't want them to appear in dxf. This is a problem if I create a dxf directly from the model.
Usually I create dxf files from drawing by adding new sheet where I create flat pattern view from the spesific part (excluding machinigs etc, only thermal cut boundaries visible). In the drawing I am allso able to show model sketches and hide unwanted project geometry. Is it possible to include these sketches to dxf?
I am unable to select Sketch geometry via a crossing window to project to a new sketch.
While in the new sketch if I select " Project Geometry " I am only able to select one line at a time. quite tedious for some of my larger projects.
I can not honestly say that this feature was available in previous releases but it seems to me it was. Am I missing a variable somewhere?
Constraint to unresolved reference geometry. Finding these magenta broken links items in a sketch is time consuming. Is there a macro that can delete them all?
View 2 Replies View RelatedTrim/ extend sketch geometry dynamically doesn't work with construction lines?
View 1 Replies View RelatedIs there a way to quickly remove all geometric elements that have been projected upon a sketch?
I don't want to remove the constraints that lock them. I want to remove the elements that basically have that constraint.
We just upgraded from 2011 to 2013 and we are having SERIOUS problems with our projected sketch geometry in parts not updating. We have only done this about 1.1 million times over the past four years and now every one of our skeleton models we touch is failing to update and causing a whole mess of delays.
I looked through the Application options for sketching and didn't see anything.
In an assembly document, if you want to project a sketch from one part into another, you go through these steps:
- select the part
- edit the part
- create a 2D sketch
- select the plane
- select project geometry
- select the sketch in the other part
- finish sketch
This creates a reference to the original sketch, so if I move the original sketch the new sketch will also move when I hit Assemble.
I am trying to do the same through the API, so I create a proxy for the original sketch and a proxy for the new sketch. I then use the AddByProjectingEntity method on the new sketch proxy passing the original sketch proxy.
This works for projecting the sketch, but it doesn't create the reference, so if I move the original sketch the new one doesn't move, even if I hit Assemble. How to create this link between the two sketches?
"Path has discontinuous segments. Use Edit Sketch to change the path geometry"
View 5 Replies View RelatedCan we now toggle "sketch only" geometry when creating drawing view sketch transient geometry in the Inventor 2012 API?
View 2 Replies View RelatedI have generated a model but want to get rid of unwanted geometry to clean it up, how do I delete unwanted geometry?
View 4 Replies View RelatedAs we have layers in AutoCAD Product, I Started using different sketches and using them as layers by turning the visibility on and off.
Can we write a macro (button Click) to turn one perticular Sketch on and off???
For example If I had a Sketch named as GROUNDFLOOR, can I use a macro to turn them off and on when needed?
I am creating a view, then a sketch on the top of the view. I should be able to project geometry of the view onto the sketch, for some rason Project Geometry icon is grayed out.
View 2 Replies View RelatedI am designing a vacuum part in Autodesk Inventor, which is essentially a long cuboid shape with various valves and spaces for windows along it's length (see attached pic). Upon finishing the design of this part, a few details need to be changed - one being the fundamental shape of the object. It now needs to be a larger square section attached to a long cuboid section (as I found out the valves on the right hand side of the drawing are around double the size they are in this drawing). Rather than restart the project from scratch, I would like to only modify one of the ends to be extruded out into a square shape, or something like that. My first idea was to use the split command in order to split the faces into what I did and didn't want to change, but upon starting this, I don't think this is the best way.
View 2 Replies View RelatedI'm using Inventor 2012, and experiencing some trouble with certain types of projected geometry that I'm using in a sketch associated with a view in an .IDW file - but only when the view involves a break (or breaks).
I'm generating section views to show the layout of hole details at various axial locations along the part. When placing a section line, I can't "pick up" any appropriate locating geometry from the view. So, after creating the view (using just a vertical section line), I edit the sketch that defines the section line. Project some geometry (the edges of the holes, in the attached example), draw some additional geometry constrained to that, then constrain the section line to that. That works fine; if I move the view around, the section lines stay attached to it. This is what is shown in the attached "before break" picture.
When I apply a break to the drawing, though, the section lines don't follow the changing view. They stay right there, as if the view had not been broken at all. This is what's shown in the attached "after break" picture. Move the view around, and they track with it - but always staying the same "real" distance apart from each other. It is as if that projected geometry were completely ignoring the break.
I observe something similar if I start with an IDW view with one or more breaks, then create a sketch associated with the view. If I project geometry, some of it projects where it should, but other geometry projects elsewhere on the page - as if no breaks were present in the view.
The part I've shown here is something I put together as a simplified example of what I'm observing. The part I'm actually trying to detail is more complicated (many more details), and much longer (so breaks are a requirement to put it on paper).
I am using inv2011. I have to create rec. blocks very often and in inv2011 . I have to constraint it in middle.
Can i write a Macto that gives me constraint rec block in sketch. This feature already available in Inv12.
I'm trying to project an edge of a cylinder in a "detail" view. Here's the process I'm taking. Click the view and pick "create sketch", then I pick "Project Geometry". Then I pick the edges of the cylinder I'd like to project and it only projects one side. I can select the edge, but when I right-click and pick done it won't project it. It appears to me that it's only allowing one edge of the same object to be projected. I've tested other objects and it seems to only do this with cylinders.
Is this a setting or a bug in 2012?
I am using projected and sketched geometry (2D sketches) in assembly space to create lines/ points that I intend to use to define planes and axes. The problem I have is that nearly all the geometry I create (lines and points in 2D sketches) is not "selectable" when I try to create planes or axes. I cannot even put a work points "on top of" my sketch points. Why are my sketches not usable in the assembly space? Since the components in my model are just two extruded rings I don't have any linear edges I can select to make this work/ define planes.
View 9 Replies View RelatedWhat is the code to delete an internal rule of a document using a macro vba?
View 5 Replies View RelatedWhen I create a new sketch on any given view and utilize the 'Project Geometry' command, not all geometry will project onto the sketch. It seems random; I've tried multiple times using different orders in which to choose the geometry. Sometimes certain geometry will project, sometimes not.
Inventor 2012
Using Inventor 2012 SP2
Have been using Inventor for 6 months or so after being on Solidowrks for many years.
With the settings I have from the start I have been avoiding using adaptivity because it causes more problems than it seems to fix. Just ran into this problem a few minutes ago.
Basic rect angle iron frame, put holes in them for fasteners. Created the cover and constrained it to the frame assembly. Used project geometry to locate all the holes in the frame onto the cover. Use the "Hole" feature and everything is good with the world.
Then changed the side pc of the frame, shortened it by 1.25 inches. Would not update until I deleted the cover and the fasteners. Even then I had to go thru all the constraints I used, edit them back to the number I had used. Once I did all that the frame was the correct size.
I must be missing something serious, it has to be easier than this to use adaptive parts.
I used "project geometry" in an assembly to locate and place a hole from one part to another. How do I save the new hole back to the original solid?
View 5 Replies View RelatedI played with adaptivity status of part 27 and sketch 3 in that part, and i now i cannot delete the sketch.
The delete command isn'ton the RMB and when i press Delete nothing happens.
I'm wanting to emboss a logo onto a part. Is it possible to project the logo outline? Or is there a better way of getting the logo into inventor? The logo file is a .jpg file.
HP Z400 Workstation
Intel Xeon @ 3.33GHz
12.0 GB RAM
Windows 7 64-bit
Inventor Pro 2014
How could I project a sketch on a cylinder?
(see image attached)
I am trying to delete fill from a sketch I have done on a drawing. (See attached). Unfortunately I cannot find any way to delete without deleting the whole sketch. I tried as Inventor said to go into Annotate Ribbon and change Layer & Style but both these dropdowns show blank when I try that. I also tried going into Fill/Hatch again hoping the new one would overwrite the old one but no success.
View 4 Replies View RelatedHow can I delete some points that show in my sketch like these (see the attachments). by the way, they are related to sketch constrains?
View 6 Replies View RelatedI want to delete the inital Sketch (if was already opened) that Inventor creates when a new part is added.
I have tried this, but doesn't work.
Sketch sketchActive = docPart.SketchActive.
sketchActive.Delete();
is there a method to project the sketch onto the part so that i can then remove 2mm of that shape from the part....?
Inventor 2013 & Inventor 2014 (work)
I have a sketch reference that is giving a cross part failure error. I am unable to select the reference in the browser so I cant delete it or update it.
How to get rid of it. Deleting the sketch and starting again will be a disaster.
Using 2011SP2 XP64.