I used "project geometry" in an assembly to locate and place a hole from one part to another. How do I save the new hole back to the original solid?
View 5 Replies
Can you add a hole back into a solid after you have subtracted it without remodeling.
View 4 Replies View RelatedI have several files that have lost their geometric data that is usually there when they are primitives. This also removes the grips that allow me to resize the objects on the fly. Is there any possible way "apply" new data to these objects without recreating them? Is there a command, an express tool or a lisp routine that can accomplish this?
View 2 Replies View RelatedIn an assembly document, if you want to project a sketch from one part into another, you go through these steps:
- select the part
- edit the part
- create a 2D sketch
- select the plane
- select project geometry
- select the sketch in the other part
- finish sketch
This creates a reference to the original sketch, so if I move the original sketch the new sketch will also move when I hit Assemble.
I am trying to do the same through the API, so I create a proxy for the original sketch and a proxy for the new sketch. I then use the AddByProjectingEntity method on the new sketch proxy passing the original sketch proxy.
This works for projecting the sketch, but it doesn't create the reference, so if I move the original sketch the new one doesn't move, even if I hit Assemble. How to create this link between the two sketches?
Should be a simple question. Using Designer Pro X I load a PNG file. I then do nothing except "save as" also in PNG format.
My expectation was I would get the same file. Instead it seems to have changed the resolution and now looks terrible.
An ordinary graphic program like paint.net or photoshop would save the same file back to disk.
There must be something I am failing to understand about Xara. How do I edit a bitmap and have it save back in its original resolution?
I just did a Circular Pattern of a threaded holes to a second solid body. The hole came through but the thread did not?Right now I have SP1 installed. I have been using solid bodies for a long time now and have not seen this.
A co-worker just came up with the same thing?
I have an existing sketch and a new sketch onto which I want to project some lines from the existing sketch.
The panes of both sketches do not run parrallel.
Normally a projection is created by imaginary projection lines from the existing sketch to the new sketch perpendicular to the new sketch.
But now and want to project the existing sketch with imaginary projection lines that are perpendicular to the existing sketch.
I am creating a view, then a sketch on the top of the view. I should be able to project geometry of the view onto the sketch, for some rason Project Geometry icon is grayed out.
View 2 Replies View RelatedI am designing a vacuum part in Autodesk Inventor, which is essentially a long cuboid shape with various valves and spaces for windows along it's length (see attached pic). Upon finishing the design of this part, a few details need to be changed - one being the fundamental shape of the object. It now needs to be a larger square section attached to a long cuboid section (as I found out the valves on the right hand side of the drawing are around double the size they are in this drawing). Rather than restart the project from scratch, I would like to only modify one of the ends to be extruded out into a square shape, or something like that. My first idea was to use the split command in order to split the faces into what I did and didn't want to change, but upon starting this, I don't think this is the best way.
View 2 Replies View RelatedIn an assembly i project a circle. I use the new center point with the hole wizard and save the assembly and the parts.
When i move the original circle the hole doesn't move with it, and when i try to edit the hole's sketch there are no dimensions. So, i cannot move the hole.
What is the best way to get a hole table on a converted SW file. Our Engineers use Solid works and I can easily import the file but when I try to create the hole table in the IDW file it comes up blank.
Do I need to recreate all the holes so they are native to Inventor? or I am missing a conversion setting.
Autodesk Inventor 2014 64 Bit Edition Build 170
Dell XPS 8300
Processor: Intel Core i7-2600 CPU 3.40 GHZ
16GM Memory
64 Bit Operating
Windows 7
Is there a way to hide project geometry from model sketch? I am modeling a sheetmetal part where I need to sketch centermaks, part number etc. for laser cutting. I want to use xy planes for symmetry reasons when sketching, but I don't want them to appear in dxf. This is a problem if I create a dxf directly from the model.
Usually I create dxf files from drawing by adding new sheet where I create flat pattern view from the spesific part (excluding machinigs etc, only thermal cut boundaries visible). In the drawing I am allso able to show model sketches and hide unwanted project geometry. Is it possible to include these sketches to dxf?
I wish to delete all project geometry in the active drawingsketch with 1 click
But unsure how to get to these constraints.
Are these geometricConstraints?
What I have now doesnt work:
Select Case ThisDoc.Document.DocumentType
Case 12292:
Case Else: MsgBox("Current Document not a drawing document")
Exit Sub
End Select
[Code] .......
I'm trying to project an edge of a cylinder in a "detail" view. Here's the process I'm taking. Click the view and pick "create sketch", then I pick "Project Geometry". Then I pick the edges of the cylinder I'd like to project and it only projects one side. I can select the edge, but when I right-click and pick done it won't project it. It appears to me that it's only allowing one edge of the same object to be projected. I've tested other objects and it seems to only do this with cylinders.
Is this a setting or a bug in 2012?
I am unable to select Sketch geometry via a crossing window to project to a new sketch.
While in the new sketch if I select " Project Geometry " I am only able to select one line at a time. quite tedious for some of my larger projects.
I can not honestly say that this feature was available in previous releases but it seems to me it was. Am I missing a variable somewhere?
Is there a way to easily "retrieve" solid model features and sketches from a stp file imported into Inventor Pro 2012 without having to recreate them?
View 2 Replies View RelatedI'm trying to create a solid using the inside geometry of a shell in Inventor 2011. is there a simple way of doing this? i have attached the part i'm working on and need a solid that represents the free space inside the shell.
View 2 Replies View RelatedWhen I create a new sketch on any given view and utilize the 'Project Geometry' command, not all geometry will project onto the sketch. It seems random; I've tried multiple times using different orders in which to choose the geometry. Sometimes certain geometry will project, sometimes not.
Inventor 2012
Using Inventor 2012 SP2
Have been using Inventor for 6 months or so after being on Solidowrks for many years.
With the settings I have from the start I have been avoiding using adaptivity because it causes more problems than it seems to fix. Just ran into this problem a few minutes ago.
Basic rect angle iron frame, put holes in them for fasteners. Created the cover and constrained it to the frame assembly. Used project geometry to locate all the holes in the frame onto the cover. Use the "Hole" feature and everything is good with the world.
Then changed the side pc of the frame, shortened it by 1.25 inches. Would not update until I deleted the cover and the fasteners. Even then I had to go thru all the constraints I used, edit them back to the number I had used. Once I did all that the frame was the correct size.
I must be missing something serious, it has to be easier than this to use adaptive parts.
If we require to create patterned holes thru a number of solids, this works great only requiring the one hole feature.
However, once an assembly is created with the parts, (these parts obviously have their own derived individual solids in them) when needing to place a bolted generated assembly to the patterned holes. It won't recognise the pattern.
So I've come to the conclusion that the bolted generator/drop place function really needs improvement for solid body modelling technique. (Mind you, the BG needs a complete rethink because its at about 50% complete).
What I can see needs to be added, is the functionality of the parts recognising the hole pattern. e.g. when using the make components function it gives an option to add a link to the hole feature.
My only other option at present is to create the holes within the assembly file and transfer the hole feature to each part file. This obviously loses the parametric functionality.
Is there a quick way to revert an edited BOM back to the original quantities before they were edited?
View 2 Replies View RelatedI recently change the volume of a part thinking that it would change the actually size of it. It didn't effect the size at all and now I don't know what the actual volume of the part is anymore. How do I find out the part's actual volume?
View 3 Replies View RelatedIn the attached file there are two custom iProperties that cannot be perminantly updated nor deleted. The iProperties are "size" and "purch_qty". These iProperties were created and set using a custom macro but they are of course accessable via the standard iProperties dialog. I can change the values for these particular iProperties but as soon as I save the file they revert back to their original values. Same goes for trying to delete them. All other iProperties, custom and otherwise, seem to behave normally.
The sketch in this file originated with a 2D DXF file for a vendor supplied aluminum extrusion quite a few years back. The original file has been copied (save-as...) to about 20 different files over the years. The iProperties in question were added years after most of the files were created, Each file is exibiting the same problem. These files are used in a LOT of assemblies. The thought of recreating all these files from scratch and updating the assemblies is not very inviting.
No other IPT files seem to be having this issue.
Inventor 2012 SP-1
Acad 2012 SP-1
Vault 2012 Update 1 Hotfix DL18480860
Windows 7 Pro 64-bit SP-1
Quad core Xeon 2.26GHz 12 GB
Quadro 4000, 7936 Mb, driver 8.17.12.6570 (265.70), Dual Monitors
SpacePilot Pro, driver 3.3.107.0
When I place the cursor over a part in an assembly it now turns bright red and semi-transparent, where to change the settings back to solid colours?
View 4 Replies View RelatedWhy do I have to select edit hole note each time I use the hole feature tool? It will not keep my settings to show qty.
It seems that I should be able to save it to my library and make it the default. I have saved library,templates all with zero luck.
See 2 screen shots in the attachment.
I've got a template with a set of Object defaults for an Inch drawing and a set for a Metric drawing. I've just noticed that within my metric set, if I insert a hole table with tapped holes, the font on the tapped holes doesn't match the other hole types. I'm searched around, but all the settings for the hole table style reference the same text style. (Please see the attached image.)
So is there a way to set a certain hole type to have a certain font or size within a hole table? Because if there is, I'd obviously like to remove it..... But I can't seem to figure out where the issue is.
I am trying to add a hole to an existing hole chart. I drop the part into a new drawing, set the ordinate "zero", and add a hole chart by selecting a few holes. When I attempt to edit the chart: click chart, right click "edit", click add hole, select new holes, right click to create, the "create" selection is greyed out and all I have to choose from is cancel. I searched the forum here but could not find a reference to this a know issue. Am I doing something wrong or is this a glitch of 2013.
We are running win7 x64 machines and this happens on both the 2013 Ultimate and Premium editions of the product.
I have had this problem intermittently for a few weeks since going to Inventor 2013 SP1.1. I have a part within an assembly and that part has holes created in it before assembling it with other parts. Now when I try and create a hole table in a drawing of the assembly I cannot select hole edges and the hole table is blank when trying to create it automatically from view selection. I originally thought it may be an alignment issue but I have since aligned everything correctly and it still persists. I can create the hole table if I import in just the part into the drawing but it will not allow me to create the table on the whole assembly.
I can also create the hole table if I use "centred pattern" and create cross hairs on all of the holes however it does not give me correct annotations for the holes as shown in attachment and I can manually change the annotations but seriously this should not be required. As shown in the screen shot it reads as A1 down to K1 instead of A1 to A10. .
Question: Is it possible to control the Hole Dimensions called out on the Hole Chart? As in controling leading/trailing zeros for main hole dim, alt home dim and tolerances? Can you combine the Main Dim with the Alt dim in a single column, separated with parentheses? (same with tolerance?)
View 5 Replies View RelatedI would like to use the hole command to place a hole in a part. When I place the hole it won't allow me to use one of the origin planes to locate the hole from. Can I only locate holes off edges?
View 4 Replies View RelatedI have an assembly that contains a part and a hole feature (the hole feature is at the assembly level). Using the api, I'm trying to get the hole location relative to the part's coordinate system in a without using the holeplacementdefinition.distance property, this way I can get the hole location regardless of the way it was defined.
View 2 Replies View Related
