Is there a way to reorder positional representations in the browser. I'd like to keep them in order of how the assembly will function. That way, it's easier to create the animation in Studio. See attached image.
View 7 RepliesI have set up my assembly file so that it has the master and two other positions. When I switch from position one, to position two, it works fine. But when I go into inventor studio, and try to create an animation by using Pos Reps, it will not do anything.I do sometimes get an error saying that Excel is required. I do have the latest version of Excel installed on my machine.
View 1 Replies View RelatedI'm using 2011 pro. When I try to animate a positional rep in inventor studio, it complains that I don't have excel installed. (see attached image) although I do have it installed. I've put the hotfix on for excel, with no effect. I've repaired inventor and repaired excel no fix though.
View 9 Replies View RelatedI'm configuring a band with different supports. Each support is configured with a range; 600-900, 900-1200, 1200-1500 etc. those ranges can be adjust by 50mm and those steps are specified by the pos reps (see attached image).
All the different supports are put in the top assembly and in this assembly I want to switch between the positional representations. I tried to use:
ThisApplication.ActiveDocument.ComponentDefinition.RepresentationsManager.PositionalRepresentations("MyPosRep").Activate
But it won't work. I guess I have to replace "ComponentDefinition" in one way or another to the component name, but I don't know how.
In Inventor 2012 I could grab any part (except patterns of course) and move it anywhere into folders, out of folder, up down, wherever, till my hearts content. But in 2013 sometimes it lets me, sometimes it does not. Sometimes I select a group of parts and when I try to put them into a new folder it will place most of them in it tell me the others are not allowed to be moved? I must stress that these are NOT patterned parts, but stuff I have moved around for at least the last 2 versions of the software. Why in 2013 can I not do this as easily or at all in some cases? Is there a new check box checked by default I can't find? I have tried switching the browser between modeling and assembly view and sometimes it works and sometimes it does not.
It does this with both content center and non content center parts.
Inventor 2013 sp1.1
place a component in the assembly.
create an assembly plane based on the assembly origin planes, (not the component origin planes).
in the browser, try to drag the plane above the component.
its not working on my machine?
I am having problems with creating positional representations. I create simple representations that go from closed to open and when I finish creating the animation I have a position representation called WorkPR1 that overwrites any positional representations I have created. What do I need to do to get my representations to be used or how do I modify the WorkPR1 representation to show what I want?
I'm using 2014
I'm looping trough positional representations in a assembly and I would like to determine if one of them is failing.
View 4 Replies View RelatedI have an issue with Shrinkwrap/Derive when using a Positional Rep.Open the derived part and try to change it to the "work" positional rep.Everything appears to work fine in the "master" rep.I have this problem in a few of my assemblies and was able to track it down to the positional rep usage in the derived part.
View 8 Replies View RelatedI have an issue where a two positional representations are showing in the spreadsheet for editing, but not showing in the tree view.
I cannot delete a representation from the spreadsheet.
When creating positional reps in Inventor 2012 SP1 it rounds them to a 3 place decimal. So If I want the constraint to be at 1.1875 it rounds it to 1.188. Is there anyway to change this to 4 place decimal?
View 3 Replies View RelatedI opened the drawing and then from the drawing opened the model. In the drawing it is showing the 4th instance of ROUND CRS-032175 X 33 as an assembly. It also is not showing in the view and yet the visibility is checked. AI2012 SP2
View 1 Replies View RelatedI am trying to use the Browsernode.addchild method to add an occurence to an empty browser folder. The code fails at this point and I gett an error pointing to the line "Call oTargetNode.AddChild(oSourceNodeDef)". I can add the occurence with the browserpanes.Reorder method without issue if the folder is not empty. The code is pasted Below.
Format:HTML Format Version:1.0 StartHTML: 165 EndHTML: 29338 StartFragment: 314 EndFragment: 29306 StartSelection: 314 EndSelection: 314
SyntaxEditor Code Snippet
DimPrcsTpAsStringPrcsTp=InputListBox("Process Type?", MultiValue.List("ProcessType"), Parameter("ProcessType"), Title :="Select Process Type", ListName :="Process Type")DimRtgNameAsStringRtgName=PrcsTp&"-"&Parameter("NoRtgsInc")+1MessageBox.Show(RtgName, "Title",MessageBoxButtons.OKCancel)DimoAsmAsAssemblyDocument=ThisDoc.DocumentDimoMatrixAsMatrix=ThisApplication.TransientGeometry.CreateMatrixDimoOccAsComponentOccurrenceoOcc=oAsm.ComponentDefinition.Occurrences.AddVirtual(RtgName, oMatrix)DimoCompDefVirtualAsVirtualComponentDefinition=oOcc.Definition'CREATE AND SET THE
[code]....
When I press F1 Inventor opens the help on my default browser (Chrome), but when I click the bynocular it uses Internet Explorer.
Is it possible to force Inventor to use a browser of my choice or the default browser?
We are running Inventor 2013 and I am trying to create a simple positional representation of a small assembly. For some reason, the "New" option is grayed out in the positional representation browser.
I can't remember ever having trouble creating them in past releases.....
The problem
- I have a top level assembly (lets call it '01.iam', which contains a range of subassemblies (e.g. '02.iam', '03.iam' etc)
- The subassemblies have positional representations
- I want to be able to manipulate the pos.rep's from the top level using iLogic.
I found this snippet of code on the forum which works when I create the rule in one of the subassemblies.
ThisApplication.ActiveDocument.ComponentDefinition.RepresentationsManager.PositionalRepresentations("MyPosRep").Activate
But I'm having trouble adapting it to work from the top level, as I would like all my rules saved in one place.
what code I would use in an assembly if I want to enable and make visible certain parts depending on the positional rep I am using.
Basically I am having trouble reading the pos rep into an iLogic code
I'm trying to employ a technique that I've used with SolidWorks. I'm working on a project with several engineers doing design work on a large assembly. The way I've seen this handled in a SolidWorks shop is to create a master assembly with sketches on the principal planes that define envelopes for sub assemblies, interface dimensions, and so on. Each engineer can have the master assembly in their sub assembly, as a guide. Where I've used this before, it has worked with integrating the sub assemblies later on.
Here's the complication: There are several different "families" of the product that require different dimensions on the master sketches. What I had hoped to do in Inventor was use view representations or level of detail representation to control the visibility of these "families" of master sketches. When an engineer includes the master assembly in his sub assembly he could then easily turn on the "family" he wants to see. But it turns out that neither view representations nor level of detail representations influence the visibility of sketches. (Position representations don't, either.) Sketches are either visible or not visible, regardless of which representation you're in.
Is there some way I can control the visibility of sketches, in groups?
How can I block the View representations on Master, so that when I reopen the asembly it is on Master, or, the view I want ?
View 2 Replies View RelatedDoes Inventor 10 not allow position representations to be created in Weldments? I Right Mouse Button (RMB) click on "Position" under "Representations", but "New" is grayed out.
View 9 Replies View RelatedThere is some association between prints and view representations i am missing.My typical process is:
-Build a model
-Create a representation
-Lock the representation
-Create a print from that representation
-Create a new representation and continue to work on the model
When i go back to the original print there is parts flying everywhere (see attached picture - hope you get a kick out of it)
Whenever I do a model update through an ilogic form my View representation changes from default to master and then i have to go and manually change them back to default also in my idw files in order to update the drawing files I have to go in and change the view representation from default to master click ok and close it then open view edit set it to default and close. Is this normal? Is there a setting so that my model views will stay on default?
View 2 Replies View Relatedis there a way I can "Unlock" my MASTER view in representations. I keep having to create new views as the MASTER is locked and for some reason I can't unlock it.
View 4 Replies View RelatedIt seems that Views are easier to use, are there any benefits of View option over Level of Detail and vice versa?
View 3 Replies View RelatedI created view representations in my assembly, for example a column with k-polates and base plates, the column is a FG part, so now i create drawings and place views on that drawing, what i am askign for is I want to place the name of the view representation in my view label as a paramater so in the event i change my view names in my model they update in my drawing, this is important because i can create a cross referance to my 3D DWXF file views.
View 4 Replies View RelatedDesign view representations in an iPart file are not included in the generated members after installing Inventor 2014 SP2 (and also in Update 1).
In the attached part factory, the two work planes are included in the members. They would need to be individually set invisible in each assembly view representation because the members only have the Master view representation.
Is there a way to have the parts list filter to show only the visible parts from the view representation, especially the quantities? I thought that was what the filter is for. And if not then what is the filter used for?
IV 2012 sp1
Inventor 2013..I am trying to show a part in a drawing of three different configurations of a casting:
1) Rough as received from the foundry
2) Partially machined or rough machined
3) Final machined
What is the most basic bullet-proof way to show this? Three different models?What is the procedure to change the representation to show changes in the model?Why does suppressing a machining feature in one representation change all representations?The rough part is brought into an assembly and the machining or removal of material happens in the assembly.
I have an assembly with a client feature that contains client graphics. I have exposed the visibility (ClientFeature.Definition.ClientGraphicsCollection[1].Visible) to the user via a context menu option. Changing the visibility currently affects all view representations. Is there a way to associate the visibility with each design view representation?
View 5 Replies View RelatedIs it possible to have iLogic rule create parts lists out of View Representations? [URL] .......
View 9 Replies View RelatedI want to modify the default Profile Grade Break label style that comes with the product as I don't want the line component in the style. When I delete the line component I have to reconfigure the attachment points of the remaining components. I want the marker to attach to the feature, then the PVIS to the marker, then the PVIE to the PVIS. The problem is these components are in the wrong order in the style and thus I can't get the PVIE to be left aligned with the PVIS. There apparently is no way to re-order the components in the style. The only solution seems to be to delete and recreate them in the proper order. Is this the case? If so then there defintely needs to be an enhancement in the product to change the order.
Infrastructure Suite/C3D 2013, LDT 2004, Power Civil v8i SS1
WIN 7 64 PRO
HP Pavillion h8xt, i7 2600, 12 GB
RADEON 6450, 1 GB