I need a Manikin in Inventor. The export from Catia V5 is failed. When I open it in Inventor i cant see anything, only 3 flats. The problem is that i dont find the command to do a Manikin in Inventor.
View 4 RepliesI need to drawing something similar to the attached image on either side of a "U" shaped rod.
The "U" shape is drawn using a sweep of a circle (the hatched section on the atatched image illustrates).
I just can't fathom how to draw the solid at the top oneiter side.
I've been trying to add a plane at an angle, then draw a circle & try to sweep that for each half of the "u", but after a few hours, total fail
I have tried in vain to construct a planetary gear train in Inventor 2011 & the spur gear generator hasn't work much since the results are far from good, I have problems getting all the gears to fit together. The Internal gear has a diametrical pitch of d=120mm & the smallest gear a diametrical pitch of d=20mm, the outcome should produce a 6:1 gear ratio. The 3 other gears only offer stabillity, but I still need to know how I get it all to fit together with my measurements?
View 9 Replies View Relatedhow to construct a curved tube/pipe run?
I've created a 3d sketch with the run of the tube on it but when I click "Derived Route" although the full 3d sketch is highlighted bugger all happens. There's nothing in the "Included Geometry" folder.
Is it because of the material? I've set it to a "Tube With Bends" and set my default radius.
Inventor 2013
I have a paper blueprint of a floor plan, where all units are expressed in mm. I need to transfer this to autocad, so I am wondering how to construct the plan in mm? (changing units, etc.)
The scale is in 1:100. Does that matter?
I am having trouble constructing the roof for a 3d model. I have attached drawings which should allow you to visualise the type of roof I am aiming to construct.
I have had a go at using the box function then using slice to get the solid into the right shape but then I am unable to slice it at an angle as shown by the red dotted line on my attachment.
roof.docx
I try to use the ACA .Net c# API to add a new construct to my project. Currently in 2013.
In the samples I've found one for basic Projetnavigator things, but adding a new construct isn't covered.
I'm starting to set up Sheets from our template but none of the construct is transfering except for dimension lines. The views are drug in from Project Navigator. Elevations are fine, but when the viewport window is made larger the construct isn't there. I've attached an example of what is supposed to be the floor plan.
I've edited the walls but that made no difference. They are set to start at 0". Is there anything I haven't checked? I'm supposed to go to contract with these drawings next week.
How do I construct a sort of compound curve using Autocad?
What I got is a circle or arc of about R=6. A node or endpoint about 5-6 units away from the center. I want a curve of R=10 to create an arc to go through the endpoint, and be tangent to the arc too. I can visualize it, but cannot draft it.
Now, I realize that there are a few possible solutions, but only one applies. I tried using the 2P function on curves, but instead of being tangent to the curve it comes up at a right angle to it. I can draw a tangent solution within a couple of seconds, but a curve?
How do you construct the actual involute curve in AutoCAD?
View 1 Replies View RelatedHow to construct Type U Threads in rectangular view.
View 1 Replies View RelatedI cannot xref a construct into a view dwg using PN. I get error "Could not reference file <construct> in <view>. Same problem whether I use relative or full pathing. But I can manually attach the construct using the XREF command. So I know it is not a file/folder permissions problem. What's annoying is that I did get it to work with one construct but not another.
I am using ACA 2013 and I see that there is a service pack 2 update.
I am drawing a house with a hip roof. The roof has a overhang with fascia and soffit. What is the best way to construct the components of the roof system. Should the hip roof and the soffit with fascia to be one system or two separate systems?
View 3 Replies View RelatedHow to construct a table to lay out the "horizontal curve" on the ground?
The steps that follow the design of the horizontal alignment is to set up it on the ground. For this purpose a table that contains angles and distances is established to set up the curve on the ground. How this process is performed on the C3D.
I have several different views xreffed into a single view, should'nt they all share the base construct? i.e. If I want to overlay the lighting plan, HVAC plan and my reflected ceiling plan- they should share the first floor construct. Instead each one brings in the same base construct and then when you overlay them, the walls interfere and you get wall errors.
View 9 Replies View RelatedI'm trying to replicate the way these circles are connected for use in a new design. At first I tried constructing this with the use of a white outline around the circles. But this isn't a solution, as the white pace around each linked circle obviously isn't a perfect circle itself.
The problem is achieving a perfectly aligned, flowing "s" curve. The connecting points that are giving me trouble are in the red circles.I can approximate the connection points, but this leaves a "kink" in what should be a perfectly flowing "s" curve. I thought smart guides/snap to point would br useful here, but to no avail.
i need a lisp that construct line between two lines of wall by selection called (Wall Centerline)
i attach example of what i want assuming that i will often isolate wall layer in the project to facilitate the task.
I want to construct lines between every two line ending point by multi selectio window instead of drawing it manually between lines ending point ?
View 3 Replies View Relatedwhen trying to create a panorama on Element 11 I get error message: window does not have a construct
View 1 Replies View RelatedIs there a way in the description field of an Inventor hole table to have mixed units? Some hole sizes at fractions, some at 2 plc, and others at 3 places.
Inventor Pro 2013 or 14
I can't get Inventor 2013 show a custom iproperty correct.My iLogic rule is this:
iProperties.Value("Custom", "myvol")=volume = iProperties.Volume
But the custom iProperty is a Yes or No.Had no problem with this in Inventor 2011.
I'm trying to use iLogic Design Copy to copy an assembly and all its associated parts to another directory. The assembly contains content center parts. Inventor warns me that the destination file of one of the CC parts (and 18 others) will be overwritten. When I go ahead and copy anyway, the copying process stops at that specific CC part. The Design Copy Progress dialog box states there is an error copying that CC part. When I close the Design Copy Progress dialog box, Inventor crashes.
The error copying the CC part: I'm allowed to use content center parts in iLogic Design Copied stuff, right? I searched some related topics and I'm under the impression that Inventor keeps the CC parts in its own directory and shouldn't be trying to overwrite them.
We are trying to get task scheduler to automatically download certain files from the Vault. Templates and Styles. The templates work great, but there is no way to specify any filetypes other than Inventor filetypes. Am I missing something? Is there a way to specify non-inventor filetypes?
View 2 Replies View RelatedCan't seem to locate the Inventor Material Library....under Default in Projects, the Inventor Material Library is highlighted in Red. Where I need to browse to inorder to locate it?
View 2 Replies View RelatedUpgrading to a new computer.
1. What is the best CPU to use for Inventor between the i7 and the a Dual Xeon System
2. Would 32GB of memory easily cover all modelling such as assemblies?
3. Any advantage of having 2 x SSD instaed of 1 x SSD
4. Looking at the Nvidia GTX690 graphics card....this should be a good card
Is there a program that can make stp files from our inventor models? Our purchasing department wants to do this task for our vendors and they don't want in have a full version of Inventor to do it.
View 6 Replies View RelatedSo I installed TD Inventor Professional 30-Day free trial and I downloaded the installer and went through the download of the installer process and it made an autodesk inventor folder on my desktop. I click on it and it takes me into the C drive under the autodesk file Inventor 2012 TestDrive and has an Application called TDSetup. Once I click on it it does a load wheel then nothing happens.
I can't seem to find a solution and I just installed DirectX.
Inventor on a touch screen style PC, and if so... does it work? This hardware looks like it would be fun to work with, but I don't know if it's quite there yet for CAD work.
View 7 Replies View RelatedHow to set off the trim inventor does when one dimensions cross another one?
View 4 Replies View Relatedwe modeled prototypes of trains (locomotives) in 3dsMax, these models will be used to produce molds and thumbnails of these, you must give the producer STP files, max does not export these files, and we have exported in various formats supported by some programs if exported STP, eg Inventor, we have exported files are STL, oBJ and DWG, so far so good, all save the parts or layers without problem.
The problem comes when exporting from Inventor to STP, nothing happens, the STP file is as if you were empty, there is nothing ..
I have attached the DWG file, if possible, have 17 CAD models for export to STP.
I would like to know how can i create or add an UOM. (for example : 25 per box) in my BOM.
View 1 Replies View Related