AutoCAD Inventor :: Cannot Auto Balloon An Ipn View / 2012
Aug 23, 2012I can not auto balloon an ipn view in a idw file? I can select the view to auto balloon but can not select any parts.
Inventor 2013
GeForce GTX 580
Windows 7 64 Bit
ADVERTISEMENT
AutoCAD Inventor :: BOM Numbering - Auto Balloon
May 31, 2012I have an issue when using Auto Balloon.
Lets say for e.g. that I have 12 parts within an assembly, once auto balloon has done it’s job you notice that No. 9 balloon is blank and No. 10 balloon only shows 1 and not 10.
AutoCAD Inventor :: Auto Balloon Command Using Drawing API
Jul 8, 2010If we can access the Auto Balloon Command using Inventor Drawing API.
View 6 Replies View RelatedAutoCAD Inventor :: Auto Balloon Macro For Custom Sketched Symbols?
May 29, 2013I'm trying to create a macro which will attach a custom sketched symbol with a leader to some specific parts in a view. By modifying some sample code I managed to create a macro which will attach the sketched symbol to the currently selected edge (see code below). However I would like to select the view and let the code cycle trough all the parts and check the filename or a custom iProperty. If the filename has a certain pattern or a specific custom iProperty exists it should add the sketched symbol. I don't really see how I should do this, I can get a reference to the selected view and as far as I can see I can use the referencedfiledescripter to open the assembly and cycle through the occurences. However I don't see how I can use this to add the sketched symbol to the occurence in the drawing view.
' Set a reference to the drawing document. ' This assumes a drawing document is active. Dim oDrawDoc As DrawingDocument Set oDrawDoc = ThisApplication.ActiveDocument ' Set a reference to the active sheet. Dim oActiveSheet As Sheet Set oActiveSheet = oDrawDoc.ActiveSheet ' Set a reference to the drawing curve segment. ' This assumes that a drwaing curve is selected.
[Code] ......
AutoCAD Inventor :: How Are Arrowhead Locations Calculated / When Using Auto-Balloon Command
Nov 13, 2012How are arrowhead attachment locations calculated when using the Automatic Balloon command? Arrowheads seem to attached to objects at rather strange places!
I normally use auto-ballooning to place balloons within a drawing and then "season to taste". Is there a way to control how and where the arrowhead gets attached to an object?
AutoCAD Inventor :: Auto-drop Doesn't Work In 2012
Sep 19, 2011Im working with IV2012 and my autodrop feature doesn't work altough the checkbox in the content center is checked on. i can't seem to find a solution on my own.
As far as I know the feature has never worked since I went from IV2011 to IV2012. (alot of troubles in the beginning btw, most of it is gone since service pack installed)
AutoCAD Inventor :: Turn Off Auto Highlight Feature In 2012?
Jun 24, 2011Is there some way we can turn off the auto highlight feature in inventor 2012? I am working in a large assembly and every time I move the cursor over the assembly it is trying to pre highlite parts and assemblys and it really causing alot of delay in my work.
View 8 Replies View RelatedAutoCAD Inventor :: Auto Cut Lines To Cropped View
Aug 23, 2012I have several cropped views in an Inventor 2013 drawing. I was wondering if Inventor could auto add a cut line to the cropped edge of objects when creating these views or alternatively if I would have to manually add a cut line through the symbols library ?
View 5 Replies View RelatedAutoCAD Inventor :: 2012 - IDW View Constant Update?
Jul 25, 2013We have views of a large system that will constantly stay in a "updating" mode.
However you can place another base view of the same system from a different perspective and that view will solve out.
In the attached image the view on the left will not finish updating while the view on the right solve out rather quickly.
AutoCAD Inventor :: 2012 - View With Positions In IDW Not Correct
Dec 10, 2012In an idw views of an assembly with positions aren't represented correctly.
In the iam in is necessarry to update for an correct representation of the position.
But when a update of the view in the idw is forced, the view isn't correct!
I ticked association of the view in the idw.
I also installed the latest hotfix for Inventor 2012.
AutoCAD Inventor :: 2012 - Sketch Setting For View From ISO To Normal?
Oct 27, 2011Is there any way to stop the flipping of the solid/sketch view from iso to normal?
its annoying to make changes to a sketch and constantly have to re orient the part after finishing a sketch, I dont want the solid model to return to iso view after sketching, is there a setting for this?
AutoCAD Inventor :: Where Did Design View Representation Icon Go In 2012
Apr 29, 2011Where did the Design View Representation Icon go in 2012?
View 8 Replies View RelatedAutoCAD Inventor :: 2012 - View Change When Opening Sketch To Edit
Jun 6, 2012If I zoom in on a small detail in a large sketch and then issue the "edit sketch" command Inventor changes the view to where the origin is visible on the screen. Is it possible to disable this?
View 2 Replies View RelatedAutoCAD Inventor :: What Line Weight Changes Thickness Of Border Around Detail View In 2012
Nov 18, 2011What line weight changes the thickness of the border around a Detail View in 2012?
Inventor 2013
Windows 7 Professional 64-bit SP1
HP EliteBook 8470w
Processor: Intel(R) Core(TM) i7-3610QM CPU @ 2.30GHz
Memory: 16 GB
AMD FirePro M2000
3D Connexion SpacePilot
AutoCAD Inventor :: Convert 2012 View Scale From 0.5 To 1:2 Or Similar Within ILogic Rule?
Jul 2, 2012Is there a way to convert an Inventor 2012 view scale from "0.5" to "1:2" or similar within an iLogic rule? I can extract the main view scale and plug it into a variable but the format isn't correct for the drawings I'm creating.
View 2 Replies View RelatedAutoCAD Inventor :: Shaded View With Edges Is Disabled In Dynamic Simulation Autodesk 2012
Dec 5, 2013I am not able to see the model in shaded view with edges in dynamic simulation environment (Autodesk Inventor 2012).
View 6 Replies View RelatedAutoCAD Inventor :: Find Balloon In DWG
May 3, 2013I would like to make use of " find in feature tree" feature, but in DWG mode; Right clicking instead in BOM on part # and showing (highlighting) the balloon in the DWG so you know where it is that you put your balloon.
View 1 Replies View RelatedAutoCAD Inventor :: No Balloon Around Numbers
Aug 15, 2012I am putting balloons on an assembly drawing, but the circle is not appearing. The arrow, leader and number are there, but no circle. What could be wrong?
View 4 Replies View RelatedAutoCAD Inventor :: Truncated Balloon Contents
Sep 18, 2012If you're displaying the part number in a balloon, is there any way to truncate what is shown?
e.g., I have a part number "abc12xyz89", and want the ballon to display only "xyz89".
AutoCAD Inventor :: Balloon Welds / Joints?
Aug 16, 2012I am preparing a weld map for our welding shop, and they would like me to balloon each joint and create a table with each joint's number, so that the welder/pressure tester can sign off. Is there a way to balloon joints and not parts, or make a custom ballooning scheme?
View 1 Replies View RelatedAutoCAD Inventor :: Balloon To Sketch Item?
Jun 16, 2011I created a hatched sketch on one of my views to represent filler material. I want to balloon to this hatched area, but it want grab it. I have the filler material setup as a custom part. I can also create a sketched symbol for this, but it doesn't appear that they would accept it either.
I am currently running Inventor 2010 Build 272, Release: 2010-sp3
AutoCAD Inventor :: Balloon Renumbering Across Sheets
Jun 15, 2012I am trying to modify the code Brian Ekins posted on Mod the Machine to renumber balloons across sheets. [uRL ....
It works great unless the item on the additional sheet is a sub-assembly. I believe it is because PartDef is declared as a PartComponentDefinition and there is nothing in the code to handle an assembly.
Dim partDef As PartComponentDefinition
Set partDef = drawBOMRow.BOMRow.ComponentDefinitions.Item(1)
partInfo(I - 1).ReferencedFile = partDef.Document.FullFileName
The Set partDef line was giving me a runtime error when it came to an assembly in the BOM until I added
"On Error Resume Next" at the start of the loop.
I tried changing the declaration to ComponentDefinition. It compiled fine, but didn't do anything. I think I'll have to add some duplicate code to handle an assembly in the BOM. Is there a better way to do this? Am I even on the right track?
AutoCAD Inventor :: Attaching Text To A Balloon?
Feb 5, 2008How do I attach text to a balloon? For example, I want to add the text "2X" alongside the balloon to denote that there are 2 instances of this part.
I can't believe that you need to make a text box each and every time you need to do this! There has to be a simpler way.
AutoCAD Inventor :: Balloon Text Alignment
Oct 18, 2005If a balloon style is set to "Linear" the text in that balloon is automatically left aligned. If a balloon style is set to "None" the text in that balloon is automatically center aligned.
Is it possible to create a balloon with the balloon style set to "None", and have the text left aligned in a drawing document. Typically the balloon text is more that one line . The new line in inserted by pressing ctrl+Enter in the override value of the balloon.
AutoCAD Inventor :: Custom Detail Balloon
Jul 15, 2013I dont know if this is possible but what i am trying to do is create a custom detail ballon & outline similar to what is attached. this is how our client wants it to look & currently we create the detail & then sketch the outline & add a sketched symbol which has the identifier. We then turn off the detail layer which has the default outline.
View 1 Replies View RelatedAutoCAD Inventor :: Balloon Arrow Turns Into A Dot?
Feb 27, 2012When im replacing the balloon arrow it turns into a black dot. Pretty annoying to change all the dots to arrow everytime.
View 4 Replies View RelatedAutoCAD Inventor :: How To Attach Text To A Balloon
Nov 11, 2003Can you attach text (qty or other info) to the side of a baloon or a point on the model view? If so can the qty update automatically?
View 3 Replies View RelatedAutoCAD Inventor :: Store Information In A Balloon?
Nov 16, 2012I'm using balloons to get information from parts, then writing that part info to a custom table. I need to keep track of which balloon corresponds to which table row.
Is there some object/property of Balloon where I can store a single number or string? I'm already using the value field, so that's unavailable to me.
Also, one balloon corresponds to one table entry. That means I cannot create a custom iProperty in the part the balloon is attached to since more than one balloon may reference the same part.
Win7 x64 - 16gb ram
i7 3610qm
FirePro M4000
Inventor 2013
ETO 6.1
AutoCAD Inventor :: Connecting Sketchedsymbol To Balloon Using VB
Nov 28, 2012I am trying to create & connect a Sketchedsymbol to a balloon. I was able to create the sketched symbol but, i was not able to connect to balloon.
The code is as below
Public Sub AddBalloonAnnotation()
Dim oGetPoint As New clsGetPoint ' custom class object
Dim oClick As Point2d
Dim DrawDoc As DrawingDocument
Dim oActiveSheet As Sheet
[Code] .......
AutoCAD LT :: Macro In 2012 To Auto Label Rafters With Lengths
May 9, 2012I need a macro to auto label, with DIMLINEAR, the lines for Rafters with the lenghts. I have the Dimension Styles set up for each roof pitch, but need a macro to auto label the line instead of clicking each line individually. Also, I can't find a ROUNDUP feature in the Dimension Styles. I've got it to round to the nearest 2' but it won't go up....if it's 11' it goes to 10'...I need it to go to 12'.
View 5 Replies View RelatedAutoCAD Inventor :: Create Custom Symbol For Balloon?
Jun 17, 2013is it possible to create a custom symbol for my balloon?
View 2 Replies View Related