I am trying to adapt the length of a rod to join two nodes. The error message reads: The new constraint conflicts with existing assembly constraints.
A simple 3-part example is attached.
The middle part should adapt to connect the two cylinders. The middle part is flagged adaptive in both the assembly and the part. The adaptive dimension is not constrained.
In inventor 2013 I want to extrude a horizontal circle on surface of a bigger vertical hollow cylinder. but what i did it enters into cylinder, and i only want to extrude it on external surface.
View 1 Replies View RelatedI've been working with adaptive parts for a while now so I think I have a pretty good handle on how they work, but I've tried every trick I know and can't get this adaptive part to adapt correctly. When I apply the final constraint, which should drive its length, Inventor tells me it's an inconsistent constraint. If the part would adapt, it should be perfectly consistent. I've attached my work-set, the constraint I'm trying to apply is "Flush:17" under "Side Guard Plate" (the last component in the browser tree).
View 9 Replies View Relatedco-workers part file. in the assembly tree the part file has
Cut-->Sketch52-->Reference38.
Now from what I understand if I adjust something in the the assembly file that this Reference38 is associated to then the cut will be adjusted accordingly. My question is, is there a way to determine what Reference 38 is referring to exactly? Which assembly file and which component/part?
I have an assembly that i want to insert in another assembly. When i do insert it i try to make it "Adaptive" but the option is graded out/not available. How can i make it Adaptive?
View 2 Replies View Relatedwhat kind of work flow I can use to make an assembly adaptive as possible..I need to make a machine fixture that requires cut outs for three parts. The fixture is made from a 8" x 5" x 0.19" thk piece of UHMW. I've made the "blank" and it features the work planes I need to place the three parts that the cut outs are derived from.
At first I just started the assembly and placed the parts where they should be and then used sketched outlines to define the cuts. However, since the parts are there they get "cut" as well.
I was wondering if I could make adaptive sketches linked to these parts and then import THEM into the correct plane. I could then use them to define the cuts.
I have an assembly with several analogical parts and they have sketches with project geometry inside this assembly ("Adaptive" function works good, look pic "Works").
Unfotrunately, one part of parts doesnt work perfectly ("Adaptive" function is not active, look pic "Doesnt work"),
I had a part which was adaptive in the context of an assembly. I managed to remove it from this assembly in such a way that Inventor did not clear it's adaptive flag (when I remove a part from an assembly, Inventor typically asks whether it should clear this flag - this time it didn't, I can not remember exactly what I did). Anyway, now I can not make this part adaptive anymore in another assembly. How can one clear this flag?
View 3 Replies View RelatedIs there a way to make a part being placed into an assembly instantly adapt using imates?
For instance:New assembly... Place box 1...Place box 2, but have it automatically placed inside of box 1 and sized to fit inside with 1" clearance all around.
I'm trying to make an adaptive part using a sweep. I'd like to be able to constrain both ends to other parts in an assembly and have it change as needed. I'm having trouble making the part adaptive though.
If I make a simple extruded cylinder, I can right click on the feature and make it adaptive. Then in an assembly it will change it's length when I constrain the two ends to fixed objects.
If I make a sweeped cylinder along a simple zig zag composed of three lines, I don't get the adaptive option in the right click for the feature. If I make the two sketches the sweep is comprised of adaptive the sweep feature has the adaptive icon next to it, but it won't change. I made both parts adaptive inside of the assembly also.
Is there some trick to making a sweeped part adpative?
I've been working with inventor professionally for about a year now doing piping and vessels for the oil field. This also involves a lot of pipe supports and platforms.
I'm trying to streamline the process right now by coming up with a way to make some adaptive bracing that I can reuse so I don't have to model it over and over. Most of the engineer drawings I get are basically the same; 2d lines for beams with work points for the bracing and typical connection details.
I start with a skeletal model and use frame gen to drop my beams in. But bracing is where I run into difficulty. I get it done but its just tedious and time consuming
Is their a way I can make a reusable adaptive or flexible bracing for this task? Here's some pics of what I've been sinking around with to try and automate this (I haven't found a good solution yet).
1. Created my skeleton
2. Dropped beams in
3. Created bracing template
4. Dropped bracing temp in assembly
5. Constrained it into place
6. used make parts to place the gusset plates into my assembly
7. gusset plates fully parametric
I'd like to have a better process of doing this. Ideally I'd like to drop a whole brace sub-assembly (gussets, brace and bolts) in to the main assembly and constrain to the drawing specified work points and be done with it.
I’m working on a project where I need to make a cable that is adaptive to 4 wheels, where 2 of them is moving.
View 5 Replies View RelatedI built an assembly made of some sheet metal parts.
Now - I wanted it to be easily changeable, meaning: in order that each part will adjust according to the other, for instance, it's length, height etc. , and will move with it and adjust, I first made work points on the mating part edges, and then in the relevant part's sketch ( I made the work point inside of the part, not the assembly!) I projected the point.
I was sure that because I see the work point with the "adaptive" symbol , the workp point will move with the parts if I change the dimensions.
It didn't work: For some reason when I'm changing dimensions, the work point stay where it was, even though it's with the "Adaptive" symbol, which makes me wonder what does it really mean (the symbol) if it point won't move along with the part while it changes.
What is the best way for me to do it? Did I have to project the points/edges in the sketch without doing a "work point' before?
My experience with the inventor lately shows that this method isn't working either. I'm sure there a "right" way to do it!
This is very important and elementary thing to do - to adjust part (with their sketches) according to the other.
Inventor 2012 Pro.
I7 workstation
how to make an adaptive airbag (part or assy??).
I've never been able to make adaptivity work correctly in kinematic applications, except with cables, but they break all the time and the model does strange things.
Right now, I need to make an airbag adaptive, so when the control arm/axle goes up and down, the airbag gets longer or shorter:
1. top plate constrained to frame rail
2. bottom plate swings off-plane (in 3d space at strange angle)
3. rubber airbag attaches to both plates
I tried to make a part, but that didn't work.
I tried to make an adaptive assembly, but that didn't work.i just can't get this to work.
IV 2010 Suite
Digital Storm PC:
EVGA & Intel components
Win 7 Pro 64 bit
1) How Can I turn on 'Adaptive' option on the menu shown in attached picture for layout part? (in assembly invironment)
2) Which process or fault leads to that problem?
what the little symbol that looks like the recycle symbol is in the model tree is? I have several parts in this assembly and many of them seem to have this symbol that says adaptive next to them and I can't find and rhyme or reason to it. I am attaching a screen shot of it. I use Inventor 2012.
View 1 Replies View RelatedI am making a truss assembly by connecting a series of nodes with 100 adaptive rods. The node positions are somewhat random, so each rod will be a unique length.
It could be done with 100 adaptive rods. Something like one adaptive part that can be used 100 times in one assembly?
I have an adaptive part which I created within an assembly. I created work planes in this file, based on features in the assembly, and created a sketch on one of these work planes. I used this sketch for an extrusion. then I wanted to reuse the sketch again for another extrusion - normally one needs to select 'Share sketch' from the right-click menu of the sketch, but this is not available. I have already experienced this (random) behaviour, i.e. the 'Share sketch' option missing from the menu. In those case it was ok to make the sketch visible, and then I could use it again. But now it doesn't work. I made it visible, but when I click Extrusion, Inventor wants me to create a sketch, claiming there is no usable sketch.
Inventor 2013
When I create part .ipt directly in assembly .iam, I can make it adaptive. I'm doing the projection of geometry. Detail goes adaptive. Geometry appears as a link.
But if I put in the assembly finished parts or remove part created in the assembly, and then insert it back, the adaptability of parts did not get to create. Then the projection geometry inserts usual nonadaptive geometry without reference.
Can I make a finished part adaptive, without creating a component at the place in this assembly?
Can a tabled part in an assembly be made adaptive? Adaptivity for my tabled part is greyed out.
View 1 Replies View RelatedI am automating model assemblies for a project.
Is there a way to make an iPart adaptive? I need to make the length of a pipe adaptive in order for it to line up. These models are not saved, but are merely generated for 2D drawings via my VBA.
The hole tool will not let me complete the holes if I delete the cross part references & re-create them again.
Note that I had to change some adaptive hole locations to follow a part that was moved & I couldn't get adaptivity turned on for all components involved (adaptivity grayed out on actual part to change). Not sure why I could turn adaptivity back on. So I opted to just recreate the cross part hole references in the parts hole sketch.
I find I have to now delete the holes completely & start over which causes extra work in IDW & IPN files downstream.
Is this as planned or am I doing something wrong. This used to be easy in 2012.
Inventor Suite 2013 Ultimate
We use a similar sub-assembly in almost every assembly we design. So what I would like to do is make a template from this sub-assembly that I can make adaptive, constrain to the proper parts and have it resize to the main assembly. I've been trying to do this for a few weeks now with little success.
I have seen tutorials make adaptive part templates but never adaptive assembly templates. Is this even possible?
I know you can't make individual parts adaptive to multiple assemblies without saving each part as a different file and I think that's where my problems are coming from. Even though I save the template as a different file is it still referencing the original adaptive part in my library folder? If so, is there a way I can make it not do that? I may be way off base there too I don’t know.
I have a set of window buttons in XPM format whose background I would like to convert to a blueish tone from their current gray. The problem I'm having is that after blending the button images to the intended blue tone they just don't look good at all.
To illustrate my point, here's the original (menu) button with gray background. Size is 12x18.
Then I took the following steps to try to apply the blue background:
- Manually edited the original XPM and removed the background (it's referenced by the '@' char.)
- Opened it in Gimp and created a new layer.
- Moved the new layer down so it acts as the background.
- Applied a fill to background layer using intended blue color (#2d6fb5).
- Set opacity of layer containing the button to 85.
- In Colours->Hue Saturation set Lightness of layer to 100 so it blends better.
This is the result of the above steps:
As you can tell the result doesn't look good at all. Is there any technique I could use to make the buttons blend in to a more visually pleasing way with the blue tone I chose?
PS: Attached original XPM.
how to adapt text on shapes.i have taken this building with a rounded shape and trying to map the text to look realist 3d,as if its mapped to the front and side of the building.so far im only going in circles and ive tried,scew and wrap tools.also mapping the text using the 3d feature,but still looks unaccomplished.
View 9 Replies View RelatedI need to emboss ( cut in ) some grooves into a cylinder, but in such a way, so that they won't get narrower. What do you think would be the best way to do that?
View 2 Replies View RelatedI have made a sheet metal cylinder with a rip. I am trying to create a seam on this rip as is done in [URL] ....... about half way through.
I have tried to go through the same steps, but I can not select the inside of the rip to built hems and flanges on. I also tried to make the cylinder by sketching 350 degrees of the cylinder instead of creating a rip, This had the same problem.
Why I can't select these edges or how I can work around it?
How can I create a rib that touches a plane and the end of a cylinder? Inventor will not do it since the thickness of the rib does not touch the cylinder (see attachment).
View 8 Replies View RelatedI am trying to CAD a model rocket I just made so I can test the aerodynamics of it. I have all of the individual parts made in inventor, but I am having trouble getting the fins on the rocket.
How can I constrain the fins (which have a flat face) to the outside of the cylindrical rocket tube? The photo shows the fin and the face (the narrow and long face) that I am trying to constrain to the tube.
I want to do a simple bend of a cylinder. That is, I have made a 40inch length and want to bend it at several places.
I keep finding a reference to bend part but the tool does not exist in Inventor.
1. I would like to scribe number of lines in axial direction & around the circumference of a cylinder
2. Secondly, I want those lines to be visible on .idw file so that I can print my drawing