AutoCAD Inventor :: Can't Make Individual Parts Adaptive To Multiple Assemblies Without Saving Each Part
May 4, 2013
We use a similar sub-assembly in almost every assembly we design. So what I would like to do is make a template from this sub-assembly that I can make adaptive, constrain to the proper parts and have it resize to the main assembly. I've been trying to do this for a few weeks now with little success.
I have seen tutorials make adaptive part templates but never adaptive assembly templates. Is this even possible?
I know you can't make individual parts adaptive to multiple assemblies without saving each part as a different file and I think that's where my problems are coming from. Even though I save the template as a different file is it still referencing the original adaptive part in my library folder? If so, is there a way I can make it not do that? I may be way off base there too I don’t know.
I have an assembly with several analogical parts and they have sketches with project geometry inside this assembly ("Adaptive" function works good, look pic "Works").
Unfotrunately, one part of parts doesnt work perfectly ("Adaptive" function is not active, look pic "Doesnt work"),
When I create part .ipt directly in assembly .iam, I can make it adaptive. I'm doing the projection of geometry. Detail goes adaptive. Geometry appears as a link.
But if I put in the assembly finished parts or remove part created in the assembly, and then insert it back, the adaptability of parts did not get to create. Then the projection geometry inserts usual nonadaptive geometry without reference.
Can I make a finished part adaptive, without creating a component at the place in this assembly?
I have a issue merging multiple parts into one assembly. When i do the constrains the parts are able to move but the pieces break part. I need to be able to move the whole assembly with all parts together without them breaking apart.
Any way to create a parametric Parts List containing subassemblies, where the subs are listed, by name/item number, in colum format, and qty's are tabulated accross rows. (see attached as an example). If the same part number occurs in multiple subs, the part is only listed once, but the quantity for each sub would be noted. The pdf attached had to be done manually, which somewhat defeats the purpose of having software like Inventor.
here's a macro I wrote to copy the filename to the Part Number iProperty for all parts and sub-assemblies contained in a top-level assembly. I wrote this after using a bunch of custom iParts and all the Part Numbers were the same for each part! (my fault of course, but a pain to fix one at a time).
Public Sub SetAllComponentPartNumbersToFileName() Dim oAsmDoc As AssemblyDocument Set oAsmDoc = GetActiveAssembly If oAsmDoc Is Nothing Then Exit Sub SetAssemblyComponentPartNumbersToFileName oAsmDoc End Sub
I have several parts which I wish to modify, but, those modifications are only being done to get some prototypes made. I do not want the changed (non-approved part) to be used in current issue drawings, assemblies etc. until I have proven the modifications and am happy with them.
I can do this by doing a save as on the part and could just replace the previous design, but then I lose the history of changes/revisions shown in Vault which is critical to me and part of using vault in the first place.
When I open up multiple assemblies at the same time Inventor cant find some of the part files, even though they are on my system. Many times if the part is in an assembly more than once, some of the instances will be there and only one or two instances will be "unresolved", of the exact same part. I can open each assembly one at a time and it will be fine, but that can be time assuming. I wasn’t able to find any other threads with a similar problem.
I am having some trouble with assemblies. What I want to do is, create multiple assemblies with moving parts and then assemble them all in one assembly. When I do this, the assemblies with moving parts come in as "blocks" and the parts will not move.
How is it possible to have a part in an assembly and then remove it when it is not required?
I have a Skeletal assembly of a cabinet with hinges on the left hand side when facing the front. When a customer requires the hinges to be on the right hand side, I need to make the lock keep disappear from the Right hand side panel sub-assembly and make it appear in the Left hand panel sub-assembly.
At the moment, I have the lock keep, the BOM structure in the file is Normal, this is overidden in the assembly to being Reference for the first instance, the lock keep is fully constrained in both sub assemblies and both are in an array of only 1. I increase the value of the array from 1 to 2 and by a distance of zero(0), the newly added part would have a BOM structure of Normal, consequently it would then appear on the BOM. This method was something I last used when using IV2009, it was a method I used to control both visibility of parts in assembly drawings and on BOMs.
I'm now using 2013 and arraying a part with a overidden BOM structure of Reference makes the new part a reference part aswell even though the file itself is BOM structure of Normal.
How do I make referenced components from parts and assemblies? (I searched the web and it said that that you can change it in the iProperties by selecting the Reference tick box under the occurance tab - but no such thing exists in Inventor 2011!
I have 2 assemblies and drawings of those assemblies. in both the same part is among the parts.
I want to change the name of the part that is in both assemblies with the Design Assistant, but i am afraid that if i will choose one of them and change the part file's name, the other assembly will be damaged. is it true?
I think this might happen because when i open only the part in Design Assistant, it doesn't let me change it's name, so, Design Assistant might not know where this part is inserted in.
I'm trying to make a few assemblies inseparable for a parts list in a Drawing, but I can't seem to make it work.
I know I have to do this in the Bill of Materials menu, but for some reason the part I want to make inseparable is greyed out whiles the one that is just one part isn't.
My only option right now is to make it a weldment which works but not ideal, because now the material isn't correct.
I'm trying this on the 099.03.00.097 assembly in the picture.
I am working in an Inventor Assembly .iam, I have about 250 fasteners (screws) that are constrained to a flat washer and lock washer. I would like to put them in as a single unit (sub assembly if you will) and then promote or explode them in the top level so that my bom has 250 screws, 250 washers, and 250 lock washers all at the same level, not associated to one another except thru the constraints that were entered in the original assembly. I have tried Promote but that doesn't work because it removes the washers from the original file and I end up with only 1 instance of the assembly. Am I approaching this incorrectly? Is there a better way? I run across this scenario with different components quite often.
Is there a way to make an iPart adaptive? I need to make the length of a pipe adaptive in order for it to line up. These models are not saved, but are merely generated for 2D drawings via my VBA.
We use simple line drawings of parts. Some of these parts are used in multiple products, however if a change is made to a drawing it has to be replaced in all the other locations
I have tried to get them to go to 3d modeling and xref in the parts but apparently that is not acceptable , since there is no master assembly, but instead folders of dwgs is there an easier way of managing this?
My issue is we have Universal assemblies that never change. These assemblies are thousands of parts. (hardware gaskets other random assemblies.) this top level universal assembly never changes.
to increase time in layouts. we would like to create these universal assemblies into 1 sold part.
Is there a was to export an assembly into a single solid part.
I have an assembly with a lot of purchased parts. I need to create a buy out list for purchasing. I've done this many times in the past and have a template set up for this purpose.
So now the problem, In this assembly, I have subassemblies showing up on my parts only parts list.
One of the subassemblies cinsists of two purchased parts. Both parts are set to purchased in the Bill of materials. If I do a parts only list on this assembly, it works as expected, showing two purchased parts. However, if I put that assembly into a higher level assembly, A parts only parts list shows the assembly instead of the individual parts.
In testing my latest automation project, I've found that I can't save copies of a part multiple times (after deleteing the files off the disk) unless I close out of the top level assembly document, and reopen it. I used Process Monitor and determined that Inventor is trying to save to an existing file instead of creating a new file.
I have a part that was derived from an assembly. However now I need to make this part have different center dimensions. Is there a way to make a derived part into an iPart without creating more parts? see attachment.
I am using Inventor 2012. BTW the part is more detailed than I am showing in the attachment.
I've been working with adaptive parts for a while now so I think I have a pretty good handle on how they work, but I've tried every trick I know and can't get this adaptive part to adapt correctly. When I apply the final constraint, which should drive its length, Inventor tells me it's an inconsistent constraint. If the part would adapt, it should be perfectly consistent. I've attached my work-set, the constraint I'm trying to apply is "Flush:17" under "Side Guard Plate" (the last component in the browser tree).
Is there a way to make a part being placed into an assembly instantly adapt using imates?
For instance:New assembly... Place box 1...Place box 2, but have it automatically placed inside of box 1 and sized to fit inside with 1" clearance all around.
I'm trying to make an adaptive part using a sweep. I'd like to be able to constrain both ends to other parts in an assembly and have it change as needed. I'm having trouble making the part adaptive though.
If I make a simple extruded cylinder, I can right click on the feature and make it adaptive. Then in an assembly it will change it's length when I constrain the two ends to fixed objects.
If I make a sweeped cylinder along a simple zig zag composed of three lines, I don't get the adaptive option in the right click for the feature. If I make the two sketches the sweep is comprised of adaptive the sweep feature has the adaptive icon next to it, but it won't change. I made both parts adaptive inside of the assembly also.
Is there some trick to making a sweeped part adpative?
I am making a truss assembly by connecting a series of nodes with 100 adaptive rods. The node positions are somewhat random, so each rod will be a unique length.
It could be done with 100 adaptive rods. Something like one adaptive part that can be used 100 times in one assembly?
I have an adaptive part which I created within an assembly. I created work planes in this file, based on features in the assembly, and created a sketch on one of these work planes. I used this sketch for an extrusion. then I wanted to reuse the sketch again for another extrusion - normally one needs to select 'Share sketch' from the right-click menu of the sketch, but this is not available. I have already experienced this (random) behaviour, i.e. the 'Share sketch' option missing from the menu. In those case it was ok to make the sketch visible, and then I could use it again. But now it doesn't work. I made it visible, but when I click Extrusion, Inventor wants me to create a sketch, claiming there is no usable sketch.
I have an assembly that i want to insert in another assembly. When i do insert it i try to make it "Adaptive" but the option is graded out/not available. How can i make it Adaptive?
