In my sketch I want to move a smaller circle that is within a circle along the Z-axis. I've put the image below to avoid confusion. I am using Inventor 2012.
View 3 RepliesIs it possible to automatically project the x-axis, z-axis or z-axis onto the sketch plane?
I.e. every time you open a new sketch the corresponding lateral and vertical axis will be projected onto the sketch.
How do I duplicate the 2D line work from a part level sketch into a drawing level (overlay) sketch?
I started a simple 2D piping system diagram sketch by opening a new part file and using a sketch to stick draw the system schematic including some annotations. Then I opened a new drawing file and made a base view of the part file to bring a view of the original sketch into the drawing.
I realize now that it would have been much easier to have created the schematic directly in a 2D sketch at the drawing level, which would have made editing the annotations much easier at the drawing level, and there is really no need for the part file to exist. I have no intention of creating a 3D model or "real" part in the .ipt file, was just using it as a jumping off point to sketch.
I was thinking that I could correct my error in judgment by just copying the sketch and pasting it into a new sketch on the drawing, but it doesn't want to work that way. I have tried copying both the whole sketch at the browser level, and the entire sketch contents (all of the lines and annotations) from the opened part sketch, but when I attempt to paste either of those into the drawing, paste does not seem to be an option. I'd rather not have to draw the whole thing again, as in typical fashion, my once simple sketch has grown in proportion and complexity from its simple beginning.
As a background....I am coming off of 10+ years using Catia (that's the software the company used) and have moved to a company that uses Inventor instead. I have used inventor for the past year.
In the past (Catia) it seemed pretty intuitive to create the vertical and horizontal during the creation of the sketch in such a way that would reflect the way you would want it defined as a view in a drawing. As well as controlling the preferred screen view (vertical +’ve to the top of the screen and horizontal +’ve to the right of the screen)
As per a previous post....I have tried the "Edit Coordinate System" but find it difficult to control the Vertical and Horizontal axis independent of each other.......
I understand that "functionally" there is no issue...but it becomes quite disorienting in a complex model when going to edit a sketch and the model spins around, showing the sketch in an orientation that doesn't relate to the models features, or "sketch related" features.
It becomes especially difficult/confusing when modifying/checking other peoples models as well.
I just wanted to support the need for this functionality. In the end it just enhances the flexibility of the software and maintain some amount of definable company standard work procedures for modelling.
Maybe it hasn't been included in the software because of proprietary reasons? I would hope there is a reason.....it seems like there are people out there who would utilize it.
How does Inventor decide how to orient the axis for a new sketch? Sometimes, when I create a sketch on a face of a feature, the sketch sometimes rotates to an odd angle (Untitled.png). I can create a sketch on a different, parallel surface and the sketch doesn't go to odd angles. Why does Inventor do this?
How do I edit the orientation? I've attached the part that I'm having the issue in. When I try to create a sketch on the face of the loft, the x/y does things I don't understand.
how to lock sketch features onto an axis or any other reference point. Also, how to bring in reference features (like in ProE)
I am trying to extrude a figure off of one that has already been sketched, and the wrong lines keep moving when I change the dimensions.
I have this assembly shown in the pic. below. I'm trying to create a point or axis in the blue corner points (to attaches something later on) but it just won't let me choose it for some reason. I know that it's possible to to do that (almost sure I already done this trivial thing in inventor.)
Any reason it's not letting me choose the sketch points/line to in order to create points or axis(s)?
Inventor 2012 Pro.
I7 workstation
i a'm using Inventor routed 2011 and am having a issue with a revolve. I created an axis with a sketch in the part. Than i created a plane that does not pass through that axis. i sketch on that plane than try to revolve using the axis. it gives me an error. what i have is a arm3+"w x 28"l that is pivoting in the in the center and about 9" from the end it tapers out .5". The bottom is the cutting edge that i need to revolve onto a weldment for matching to keep a tight seal.
View 8 Replies View RelatedI can't seem to find how to use the Inventor 2012 API to project an entire sketch profile from one .ipt to another .ipt file from within an .iam file.
i7-2720QM Dell Precision M6600, Win 7 Pro 64-bit, 8GB RAM
Autodesk Product Design Suite Ultimate 2013
Autodesk Vault Professional 2013
I am creating a part that consists of a series of intermediate Lofts. The various Loft termination profiles are sketched on a series of stacked planes, most of which are parallel to one another. I have a Work Axis (oriented at an angle off of true vertical) that penetrates all of these sketch planes, essentially forming a "central axis" for my part. Most, but not all, of my sketch planes are normal (perpendicular) to that axis.
I want to use my "central axis" as a reference point in each of my sketches, i.e., the point where the axis intersects the sketch plane. I am having a minor difficulty.
When I project my central axis into a sketch whose plane is normal (perpendicular) to the axis, Inventor displays a reference point where the axis penetrates the plane and I can dimension my sketch geometry relative to that point. Conversely, no such point is displayed when I project the axis into a sketch plane that is NOT normal to the axis.
Is this correct behavior? To have a dimension able point on my "non-normal" sketch planes, must I create explicit Work Points to mark the intersection between my Axis and such planes, and then project those points into the related sketches?
I am using projected and sketched geometry (2D sketches) in assembly space to create lines/ points that I intend to use to define planes and axes. The problem I have is that nearly all the geometry I create (lines and points in 2D sketches) is not "selectable" when I try to create planes or axes. I cannot even put a work points "on top of" my sketch points. Why are my sketches not usable in the assembly space? Since the components in my model are just two extruded rings I don't have any linear edges I can select to make this work/ define planes.
View 9 Replies View RelatedIn previous versions when you hovered over an invisible axis in the browser you could see the whole line in the model. Now you just get the end points displaying as yellow circles and it can be quite difficult to see where the line is. What's the point of this change? Is there a way to get the old behaviour back?
View 1 Replies View RelatedI just installed a student version of Inventor Pro on my comptuer. I have used this and several other similar software packages before. My problem: when I open a new part file, it takes me to a gray screen. No coordinate axes, view cube, nothing. When I click "Create 2D Sketch," still nothing. Same gray screen. If I draw a line, it doesn't show anything.
I've gone to View -> Object Visibility, and everything seems to be checked off as it should be. I've also clicked User Interface, and it shows the View Cube among other things as being selected.
The software didn't prompt me for an activation key, not sure if that may be relevant to the problem?
As soon as I open a piece or try to make a new piece, it crashes! I can open the program but can't use it! I installed it and activated it and I can't use the program at all. I have sent many error reports beacuse I have opened it many times and had it crash many times and have always given my email address. Attached is the Error Report Details screen shot.
View 3 Replies View RelatedI have a part and I need to scale it in the Z-axis only. It is impossible for me to rework the base geometry directly.
I have made some attempts to figure out how to do this on my own but all have failed:Thicken/OffsetCopy Object + Move Bodies + Combine (wouldn’t let me create a solid with Copy Object)Rectangular Pattern + Combine (works but not the desired result. adds a constant offset to the part, not % based, humongous model size)Derived component (uniform scaling only, prefer to modify the original file for file structure reasons)
I would like to create a curved surface from a flat part. I have designed the 3d part on the XY plane and would like to have it curved as if placed on a sphere.
I have attached a picture of what I want to achieve. The part is curved in both the X-axis and Y-axis. Unfortunately I cannot attach the part file due to proprietary rights.
At first I used the Bend Part feature and created a bend on both sides on one axis.This was done by sketching a line in the center of the part, which is symmetric in the x-axis and using Bend->Sides. Then I sketched another line which is symmetric in the y-axis and this intersects with the first line used for bending. I have found that I cannot create a second bend using this new line.
I derived a part and added extrusion.
The original part is rotated at an arbitrary angle and i want to align the origin planes differently.
The part isn't symmetrical about the YZ plane, you can see it in the sketch of extrusion 1.
Now i started a new sketch, sketch 24, and the part is positioned like in the picture, with the YZ plane not vertical.
Using API is there a way to add a WorkPoint where an Axis and a Part Face Intersect?
I need this to be able to create a WorkPlane normal to the surface of the part at that location.
Although the part, marked in blue in the picture, has, to my opinion, degrees of freedom, i cannot rotate it round the main assembly axis, the Z axis.
Maybe it's connected to the 2 holes underneeth it, which i projected?
Or maybe because of the axis i made through the M24 thread?
I have several parts designed "car line" in their respective parts.
I would like to simply add them to an assembly in their respective axis positions.
Obviously "place" drops in in an arbitrary position to then be "Assembled". Not what I am looking for.
I was looking for a copy/ paste function between part / assembly but there seems no way to paste into an assembly.
There are two cases, that should behave the same, but they don't.
First program works normally. Inventor generates a circular Pattern with the given Part.
' Part referenced in Obejct-Collection-Object
o_ObjectCollection (is defined)
' reference an Axis of the Assembly
[Code].....
Now, the second case, I try to take the Work Axis from a Part, that is placed in the Assembly,
but Inventor does not generate the Pattern. If I set the Axis visible, or even rename it, it works. But the AddCircularPattern does not work.
' Part referenced in Obejct-Collection-Object
o_ObjectCollection (is defined)
' reference an Axis from Part, placed in Assembly
[code]....
I have several name plates which are embossed, and only the description changes from job to job, but find it a nuisance having to go into the part,edit sketch then edit text! each time I want to change the description .
I was initially going to get round this by creating a form and linking it to the text parameter! But for some reason it won't take in the text parameter I created and will only find and take in numerical parameters?
Is there any way around this? I know it is possible in inventor 2013. I am currently working with Inventor professional 2012.
Is it possible to move a 2D sketch vertically? I have a sketch on the XY plane, but I'd like to move it up to another entity.
I can see how to do it in 2D (in the XY) plane, but not along the X axis.
How do I slide the highlighted part toward the middle?
View 4 Replies View RelatedCan I pick a 3D sketch and move the whole thing closer to 0,0,0 ? It is currently sitting around 5km,10km,2km from zero.
This makes everything very chunky, and very difficult to visualize anything correctly.
This was generated from a site survey, which was work in progress, it has now all been finalised, but I don't want to loose a weeks work by starting again. (Using AutoCAD to move the points to Zero)
Is there any way to stop the flipping of the solid/sketch view from iso to normal?
its annoying to make changes to a sketch and constantly have to re orient the part after finishing a sketch, I dont want the solid model to return to iso view after sketching, is there a setting for this?
I would like to reuse the existing sketch on the other part. Usually I did it without problems. But now after I have pasted the existing sketch I cannot move or rotate it. While moving or rotating Inventor usually prompts for braking some constraints for this action. But nevertheless it does not allow me to move or rotate. It says something about "constraint settings for sketch edit tools" -- cannot get any hint of that in a whole phrase nor in part [URL] what else Inventor wants so I can reuse my sketches??
View 4 Replies View RelatedIt goes f.e. like this:
I draw a line (no constrains) and I can move it by grabing an end or whole line by click&hold mouse button, great.
But after couple minutes of work with part and sketches I can't grab anything. Even on new created sketches and new lines. Click and drag just open rectangle selection. Oh, between these phases there is a phase when 2nd click&hold works...
When I open/create another part it is normall, but this one I must close and open again.
I can add sketch on a part's workplane (xy, xz, yz) by using sketchs.add.is there anyway i can select a face of part and create a new sketch?
View 6 Replies View RelatedI have a feature that is very similar to a CAM that I need to cut other feature with. The second feature needs to maintain its position way from the CAM feature just as a CAM follower would. The CAM is made up of arcs. If it were made from a spline I would be all set. Is there a way to either convert the arcs to a spline or make a CAM follower type arrangement in a part sketch?
View 1 Replies View Related