AutoCAD Civil 3D :: Unable To Get Lat And Long To Display Using Note Labeling
Jun 29, 2012
For some reason I am unable to get my lat and long's to display using note labeling in C3D 2013.
I can setup a labeling style to add and display NE coordinates where ever I place them on my surface but my Lat and Long label style remains blank.
I've checked layer being on, text size, drawing unit/zone settings, even tried replacing my NE label style call outs in the NE label style text component editor properties to Lat and long and still remains blank in my composer preview....
Is there a way to display vertices and elevation points of featurelines so I can see where to apply labels to individual segments? Without the markers it is a trial and error process of placing labels, then picking the line to activate the grips to see if I missed any segments.
I know I could create a label style that labels all the vertices but that just adds clutter. I'd really like to see some sort of marker if possible.
Infrastructure Suite/C3D 2013, LDT 2004, Power Civil v8i SS1 WIN 7 64 PRO HP Pavillion h8xt, i7 2600, 12 GB RADEON 6450, 1 GB
Is there any way to change the format of Lat/Long in a C3D point list display from degrees, minutes, seconds to decimal degrees? I have looked pretty hard, but can't find anything. The geodetic calculator only does one item at a time, I think. Any plug-ins out there? I suppose this could be on a wish list as well.
I am using R2012.and have ended up manipulating point values in Excel-not a quick way of going about it.
I've used AutoCAD 2013 on other machines and have no had this issue.
When pasting to the command line there is a huge delay from when I hit CTRL-V until the actual text is displayed in the command line. It takes roughly 4.5 seconds for the following to display after pasting: (command "-view" "D" "*"). The time it takes is roughly the same and does not depend on the size of the lisp that I'm pasting.
The command bar is docked to the bottom and there is no transparancy enabled.I have tried setting AUTOCOMPLETEDELAY to 0 and 10 with no change.I have completely disabled all Auto-Complete options and it still happens.
There is also a significant delay between Auto-Complete populating the list of suggestions and when I am able to use the arrow keys to move the selection box down to pick a command.
I have a document for a book with 1400 superior note numbers in it. At the end of the document is a list with the 1400 connecting note texts. Unfortunately they are NOT connected! How can I connect the note-numbers with their connecting note text?
I have recreated two surfaces for my design, existing and proposed. I had used polylines for contours for in each surface. I tried labeling the contours but it will not let me select the contour itself.
I then tried to make the contours to 3d polylines and again added them to the surface and rebuilt. I still am not allowed to label the contour since it doesn't let me select the polyline. I am able to select the surface however.
Is it a know issue that when you have a General Note style with a Dragged State where the Display is set to Stacked Text. If Background Mask is set to True. The Mask does not encompass the whole text.
Civil 3D 2012 SP 2.1 Dell Precision T7400, Xeon CPU 3.16 GHz Win 7 Pro, 64-bit,12 GB RAM, Nvidia Quadro FX 4600
I was wondering if it is possible to use an expression in a general note label? The type of label I am using is a general note label that displays our finish grade profile elevation in plan view. What I am trying to do is add a value to that label for the TC elevation and G at the ROW. I noticed in the settings tab of the tool space, surfaces has an expression button that has what I want but I am not seeing that under General/Label Styels/Note. Is it possible to right my own expression? We are using Civil 3D 2008 with Windows XP.
Any way to label a pipe part way between structures? I would like to be able to label a sanitary line where a service ties in with the main line invert.
I want to label the surface sections (eg, fg) in a single location something like what is shown in the attached image.
Currently I am using a major offset label which refers to the surface description* where the surface name is stored. I set the increment to a suitable number which results in multiple labels along the section. I then drag one into position and delete the rest using ctrl-select. While it would be far easier to use multileaders to acheive the correct look, they don't update location with the section views.
We use the description to store the 'friendly' name as our object naming standard wouldn't necessarily make sense to the viewer of the plans.
I am labeling structures in a network on the profile view. I cannot get the leader when i drag the label to anchor to the top of the structure? Is there a way to do this, i figured out how to have the label insert at the middle of the top line of the structure.
Civil 2014-Infrastructure Design Suite Windows 7 Professional-SP 1-64 bit system Intel Core i5-2500K cpu @ 3.3ghz NVIDIA GeForce GT 430 8.0 gb ram
how label only the top of my road surface in section view? The road slopes -2% towards a ditch but my my code set labels both the top of road(-2%) and what I assume is the bottom of the road surface (2%) which I don't want to show.
Is it also possible to label my side slopes as 4:1 instead of 25%?
I'm running 2012. Is it still true that I need to label my contours in every drawing? I have a drawing that contains my existing surface (about 90 Acres). I have labeled the contours in that drawing. I then have a output drawing that the existing contours are a data shortcut. The contour labels do not show up.
Often I've found myself dealing with some pretty complicated surfaces that have a lot of nooks and crannies, and many of the contour lines are only in a corner of the surface or are small and closed, and thus when I find myself wanting to have contour labels on all of the contours, there's not really one line I can draw using the "Create Multiple Labels at Interval" option to ensure that every contour is labeled. Thus I end up doing "Create Multiple At Interval" with a few different lines intersecting contours, but I often end up hitting some of the contours multiple times and I get a mess of labels.
I haven't been able to find a way to automatically just multiple labels on all of the contours at an interval in one fell swoop, so I started trying to program one...but then I got stuck with that, too.
Does any built-in method of doing what I want to do, or do I need to continue pursuing a programmatic solution?
How can I make better the second labeling precision in Civil 3D? It's only has four digits precision for the seconds. I did change the ambient settings (Lat Long precision to 8) but haven't got the result.
I have a drainage model, the data for which has been imported from microdrainage into Civil3d (.sws file) .
The engineer working on the project is playing around with the Invert and Cover levels so I reload the same updated .sws file into my model almost daily expecting the information shown in the labels of the pipes and manholes to simply change. Instead mine seem to disappear and I have to relabel the whole network again.
This wouldn't be much of a problem because labeling only takes a few minutes but with this particular scheme, the client wants the labels shown in a box with a leader. When I relabel, the boxes automatically snap to the center of the manholes without a leader and i then have to drag each one away from the manhole to get the leader to show up.
Where do I set the contour labeling line to not show or be on layer defpoints. When I click on the label line and right click I can edit the contour label line properties and change the Display contour label line to false but not sure where the style is.
How can I show the description (in this case, MUDSTONE) in a profile label? I've tried modifying the style but the description refuses to appear even though it is one of the available labels.
When I draw in the profile layout I'm getting odd results when the labeling is placed. See attachment. I have been looking through the styles trying to find what is wrong.
Everytime I use the label line command, when I go to plot my drawing I see a box around my label and the label is either chopped off or missing. A rectangle prints out around where the label is.
I was just wondering if you can customize your interface so you can edit note labels (or any labels for that matter) by double clicking. I've already gone throught the cui files but I can't find anything. Am I missing something. c3d 2007
We use STB plot style tables for all of our drawings. I have several general note styles setup in Civil 3D 2012. When you pull the note text out so that you have a leader, the leader does not plot per the plot style assigned to the layer that the note is set to display on on the General tab. It appears as the proper color and freezes with the layer properly, but it plots with the settings of the plot style assigned to layer 0. Is there a reason that the leaders don't use the plot style setting form the layer it is displayed on?
When I maximize a view port, then zoom in or out, the note labels change scale. I like the way C3D General Note Labels rotate and scale with different viewports, but is there a way to stop them from changing when you are just viewing by maximizing? I know that I can zoom first, then maximize and as long as I don't zoom again, the scale won't change, but this is not practical.
I have a job where there are 3 round pipes and one elliptical pipe going into the same structure. When I put a label on the structure, it shows all 4 pipes, but I can't figure a way to show the elliptical pipe dimensions as 29x45; It only comes in as 45" RCP. I have tried to manipulated the text, but it won't let me me change the individual pipe text in the structure label. When I change the label to read Height x Width, the round pipes show the same as elliptical pipe. Is there a way for my label to show 3 round and 1 elliptical pipe size, or do I have to manually add the elliptical pipe size (which I'd prefer not to do)?
Just started a drawing in C3D 2013 using an existing template. If I draw an arc using the "Angle" rather than length or radius, entering the angle as 11.1601, then label the arc, the delta angle is converted to hms or 11.0936 . The template and labeling style are ones we've used for several releases. I've compared the feature settings, units and the curve labeling command and can not find where this is being changed.
We recently started using Civil3d 2013. We made a huge jump from LDD 2008. We have profiles designed and data short cuts are created. We have existing and proposed.
Now i've created a reference and brought them into another drawing. First I tried to set up the color and linetype for each profile. When I do this. Both the existing and proposed become the same color and linetype.I do not see how to select the existing from the proposed and set the color and linetype.
Next I select the proposed profile and right click and select Edit Labels. I start to create the PVI labels. When I do this the PVI's for the existing profile get labeled. I want the proposed profile labeled. Not the existing.
I have a job where there are 3 round pipes and one elliptical pipe going into the same structure. When I put a label on the structure, it shows all 4 pipes, but I can't figure a way to show the elliptical pipe dimensions as 29x45; It only comes in as 45" RCP. I have tried to manipulated the text, but it won't let me me change the individual pipe text in the structure label. When I change the label to read Height x Width, the round pipes show the same as elliptical pipe. Is there a way for my label to show 3 round and 1 elliptical pipe size, or do I have to manually add the elliptical pipe size (which I'd prefer not to do)?
