Let's say I have an assembly called Original, as shown below with a 6m wide lane. Now I want to target it to 8m wide for some road widening. Now, will it stretch along the slope of the subassembly (Case 1) until 8m width, or will it just shift laterally to 8m (Case 2)?
I know that we can set the default slope of it, but I'm not sure if it gets overriden due to the Target-width process.
I have a variable sidewalk width and would like my corridor to follow sidewalk as defined by Target Alignment for Sidewalk width (polyline). My sidewalk is merging at ends with roadway however my corridor feature lines presenting sidewalk is not following/merging with target. In all other locations, it follows the target width however where sidewalk merges with road, feature line goes straight.
Attached PDF should hopefully explain what I want to say. Could not attached dwg due to size issue.
I am using Basic Curb and Urban sidewalk assembly wherein my Blvd targets are set to 0 (none).
How can I make my corridor follow sidewalk width target exactly.
I am using C3D 2010 , Win 7 Pro.
I am trying to model a DOT project in a fashion that allows a corridor surface creation for not only the finished surface, but also the datum surface. This is a machine control project currently under construction. One of the DOT's typical sections includes a shoulder subassembly with a grade break in it. This particular assembly varies in width at the grade break. I would like to have the option for a target width alignment at the grade break.
See attached sketch.
how to create corridor, and I have a question about assembly elevation targets.
When creating a corridor, the profile is required as dependent object, which gives the elevation of the centerline of the road. Based on the definition of assembly, the elevation of the corridor at the offset targets can be determined by the profile. My question is if the assembly elevation target specifies the elevation at the offset target too? If so, why both profile and assembly elevation target are required?
I created an assembly with a broken back subassembly. I moved it to a 40cm horizontal offset away from the axis. I attached it to a corridor using two polylines as targets. One for the broken back and one for the outside lane. In civil 2011 everything works fine.
In civil 2012 the ETW is offseted by the same value i moved the subassembly away from the axis! If i change the subassembly offset to eg 1m then when rebuilding corridor the ETW moves to 1m away from the target polyline!
Same strange behavior using subassembly R2011 or R2012.
See the attached dwg.
Suppose I have a rectangle 10 x 8 and then I join the middle points of the widths with a line ... so I will end up with 2 boxes of 5 x 8. Now what I need to do is to stretch the side by 2 units to become 12 by 8 but I want the middle line to move automatically during the stretching process so I end up with two boxes of 6 x 8.
View 9 Replies View RelatedSo I need an sub assembly similar to the SuperLayerVaryingWidth, but combined with BasicLane Transition sub. If the SuperLayerVaryingWidth sub would follow an ETW profile to set slope, then I would be set. Any tips on how to create this? I'm pretty rusty at building custom subs.
View 2 Replies View RelatedIs there a way to stretch the width of text, once it is in an envelope or on a path? You can adjust the kerning(spacing), but I don't see anywhere that you can adjust the width of the letters.
An example: I have the word MAVERICKS on an arched path in a design. I want to change that design for the RAMS, so where it says MAVERICKS it will now say RAMS. The problem is RAMS is a much shorter word and I need it to stretch to the same width as the previously used MAVERICKS.
We are currently STILL in the transition from LDD to Civil 3D 2013. Is there an easy way to stretch the contours within a surface without physically editing the surface. Right Now, I have a couple contours that have have spikes in them from lack of survey data. The Problem is that if I don't change the contours, I have to show steep slopes between them which I would rather not do.
Do I have to keep editing the surface to try and resolve this problem or is there a way I can just stretch the contours?
Right now I resolved the problem by coping the surface, exploding it and putting the contours on a different layer so that I can stretch them as I see fit But this is not a time effective solution.
I would like to determine the length, width, and height of a assembly.
Can i use the bounding box method to do this, or the range box?
I am building sub-assembly, I just want to know if there is any example or tutorial on how to add target parameters to sub-assemblies.
View 6 Replies View RelatedI have a civil3d model and now have an amended layout which I need to update to.
xref'd layout is 2d so I want to snap blips on my feature lines from the original location to new location while maintaining their z value.
I know you can turn off and on the ability to pick z values but can't remember the command (lost notes).
I have tried changing the osnapz option with now luck.
I am using OffsetTaget.isValid in my subassembly.But i realize that when i put this formula it checks the whole drawing for that target and if the target polyline exist even a piece of polyline in the drawing then C3D considers it for all sample lines.Is ıt possible to be able to check each single sample line if it is going to intersect that target polyline or not?
Civil 3D 2014 x64
Windows 7 64-bit
16GB RAM
i have just spent 8 hours today trying to find a link that will vary target a poly line that i have set. i cant seem to find the link that will do what i need as per the attachemnt. the section between the edge of the foot path and the start of the fill/cut slope needs to be variable
i know how to set all the targets but this link seems to be a fixed length.
I want to programmatically assign Targets to subassembly of baseline Regions but I could not Success in that here it is the code
Corridor corridor = ts.GetObject(icor.ObjectId, OpenMode.ForWrite) as Corridor; foreach (Baseline b in corridor.Baselines) { al = ts.GetObject(b.AlignmentId, OpenMode.ForWrite) as Alignment; foreach (BaselineRegion br in b.BaselineRegions) { double st = [code]........
What i want to do is ; i have a corridor with both right/left sides ending with linktosurface with fixed slope.In some sections my existing surface is not wide enough to get intersection with link to surface with fixed slope. So i want to use this "conditional horizontal target " if my surface is not enough wide for intersection then just intersect or go to the edge of my existing surface. But i learned that surfaces cannot be used as an offset target with that subassembly.
View 9 Replies View RelatedI created a custom assembly that has an offset target. Is it possible to program my subassembly to target only on the side of my subassembly (and not criss-cross onto itself it the target is on the other side)?
View 9 Replies View RelatedIn particular, I am attempting the infamous task of creating driveway openings using a horizontal target with my sub-assemblies. I referred to the AU 2010 video tutorial that gets passed around here on the boards, and for the most part, it works with ONE tiny exception.
Like in the AU video, I set my conditional target to look for a particular layer, and I first attempted the exercise by placing ONE polyline (i.e. driveway opening) on the layer, and set set conditional "found" and "not found" targets to find this pline. The target found the pline on the layer on the right side of the road where I drew it, and created the opening as hoped, but it created an opening on the LEFT side of the road as well!
What do I have to do to prevent the conditional horizontal targets from ignoring the exact opposite side of the road? In my assembly, the left conditions are set to LEFT, and the right conditions are set to RIGHT, but when the corridor gets modeled, BOTH sides of the road will show an opening even if there is only one pline drawn.
I can import my SA fine, but the problem is that the top of it needs to be cut off 1 m above the existing ground (which is already a surface in civil 3d). How do I setup the target surface so that when I import the SA into my drawing, I can link it to that surface and have it cut off 1 m above the surface?
View 5 Replies View RelatedAm struggling to pull off some corridor but the standard daylight subassembly is letting me down. It mulfunctions when I connect it to the Generic Linktoslope subassembly. In some Areas it works fine but in others it doesn't. My plan is to apply a ditch at the point where the LinktoSlope meets the ground level and to have this ditch again daylight back to the target surface.
View 3 Replies View RelatedI have just installed Civil 3D 2012.
For all previous versions I was able to change the default Profile <<C3D_Metric>> in the Shortcut Target to my custom Profile with no load errors.
When I do this in 2012, I receive a rash of errors upon load(see below), wich results in an incomplete program.
c:program filesautodeskautocad civil 3d 2012acmapworkspace.arx cannot find a dll or other file that it needs.
c:program filesautodeskautocad civil 3d 2012acmapdwfapi.arx cannot find a dll or other file that it needs.
.Failed.
AcMapWorkspace.arx Load Failed
Unable to access Shared Pipe Catalog folder.
Please verify configuration.
Run 'setNetworkCatalog' to reset.
c:program filesautodeskautocad civil 3d 2012acmaploader.arx cannot find a dll or other file that it needs.
c:program filesautodeskautocad civil 3d 2012aeccuimodel.arx cannot find a dll or other file that it needs.
How can I set things up so that it will load with my settings?
Windows 7 64 Bit
Intel(R) Core(TM) i7
860 @ 2.8 GHz
8 GB Ram
I've to make a tunnel on my project. I get some subassembly on web but all the tunnel subassemblies have the target point on Width or Offset Target and Slop or Elevation Target. I don't know whats happens but only my region that owns the tunnel subassembly isn't recognizing on corridor, and isn't drawing on my sections too.
View 9 Replies View RelatedThis is my first corridor and I've been slowly working my way through it, but just seem to be running into problems left and right. My latest problem is the following;
I have my Corridor's Subassembly Daylighting set to target my Left side 33' R/W offset alignment. For 90% of my alignment everything is working fine or at least appears to, but I have 3 different areas where the Corridor refuses to daylight from the bottom of the 1' ditch out to said left alignment target even though the ditch is well below existing grade. I've attached 2 screen grabs.
Windows 7 Prof w/ SP1, 64bit, Xeon 3Ghz, 16GB
Civil 3D 2013
How to create multiple offset target. It mean lane, median, sidewalk extra. I have attached exactly what i expect.
View 3 Replies View RelatedWhen trying to make an existing features corridor when I select Target to set the existing surface I get an error
"No target found in the scripts."
I have attached a word file with the error as it appears on the screen.
if i want to target the existing surface beyond the edges of my road/sidewalk, should i use the link slope to surface subassembly at both ends? i want the model to test if in a cut or fill situation, and then target.
Civil 3D 2013 SP1, Win 7-64 bit
12GB RAM
When I run my corridor I get an error message that says "Failed Target Not Found" it is for the subassembly provided by WisDOT called UrbMedian.
View 4 Replies View RelatedI thought I created a rail sub assembly.
So I created the rail sub assembly everything looks great in sub assembly composer.
Start a new dwg data reference in the rail alignment, Note the rail alignment type is set to rail.
Create an assembly and under the Construction tab for the assembly the Assembly Type is set to Railway. Attach my custom sub assembly to this assembly.
Created a corridor and I get this error: Something wrong with current subassembly: Operation is not valid due to the current state of the object.
So I delete my sub assembly attach the Civil 3D Rail Single sub assembly. Re run corridor and everything works fine.
So I promote the alignment change type to centerline. Delete the Rail Single sub assembly put my rail sub assembly back. Rerun the corridor and everything works.
So then I undo everything up to the point of promoting the alignment.
Opened the base file changed the alignment type to centerline.
When I tried to synchronize the references I ended up a broken reference with the following error. Invalid reference. Synchronization failed
Not good we already have plan sheets cut.
where in sub assembly composer were do I define the sub assembly to be for Rail?
I have a finished corridor, but now I need to add marked points to label a few key grade breaks in my cross sections. When I attempt to add the marked points on some of my sub-assemblies it gives me the error that the sub-assembly is not part of the assembly. I can right click the sub-assemly and choose "Add to Assembly" but when I rebuild the corridor it strips all the sub-assembly data from my assembly and leaves me with essentially a null assembly for the range.
View 4 Replies View RelatedIs there a way in AutoCAD to calculate the average width between two irregular lines, such as the average width between stream banks?
View 2 Replies View RelatedAny way to make Acad C3D hold the value for MTEXTCOLUMN = 0? I am having issues with it resetting my column width to 0, even after I have formatted all the Mtext to read how I want it shown. Once I close a drawing and open it again, the formatting changes that I have previously set return to "dynamic" and column width = 0. I just want to turn off the dynamic setting so it stops messing up the formatting, but I can't get it to retain the dynamic setting. Currently running C3D 2012.
View 4 Replies View Related