When trying to make an existing features corridor when I select Target to set the existing surface I get an error
"No target found in the scripts."
I have attached a word file with the error as it appears on the screen.
When I run my corridor I get an error message that says "Failed Target Not Found" it is for the subassembly provided by WisDOT called UrbMedian.
View 4 Replies View RelatedI want to programmatically assign Targets to subassembly of baseline Regions but I could not Success in that here it is the code
Corridor corridor = ts.GetObject(icor.ObjectId, OpenMode.ForWrite) as Corridor; foreach (Baseline b in corridor.Baselines) { al = ts.GetObject(b.AlignmentId, OpenMode.ForWrite) as Alignment; foreach (BaselineRegion br in b.BaselineRegions) { double st = [code]........
how to create corridor, and I have a question about assembly elevation targets.
When creating a corridor, the profile is required as dependent object, which gives the elevation of the centerline of the road. Based on the definition of assembly, the elevation of the corridor at the offset targets can be determined by the profile. My question is if the assembly elevation target specifies the elevation at the offset target too? If so, why both profile and assembly elevation target are required?
if i want to target the existing surface beyond the edges of my road/sidewalk, should i use the link slope to surface subassembly at both ends? i want the model to test if in a cut or fill situation, and then target.
Civil 3D 2013 SP1, Win 7-64 bit
12GB RAM
i have a corridor. the corridor feature line that is supposed to hit the proposed centerline is following my existing grade instead of where the profile is. in other words, the corridor line i need at the centerline when i do "feature lines from corridor" is following my existing grade instead of the top of my road. did i accid. change something? i need it to follow the top centerline of my road. the red arrow is the line i need at the top centerline.
View 3 Replies View RelatedI've worked with LDD for 11 yrs. Last week the IT guys changed my PC to Windows 7 64bit, so I can't have LDD and I have to work with C3D. so I am following software tutorials.
for designing a road I created:
alignment ---> surface profile ---> layout profile (project line) ---> assembly ---> subassemblies ---> corridor ---> set target surface and frequencies
Corridor is created with daylights ,but I don't see existing ground in corridor section editor.
There is nothing about this in tutorial. Also I don't know how to calculate the volumes, in LDD after this stage we could calculate the volumes. i think in C3D I should do more for calculation.
How to prepare for rendering Existing ground with cutted corridor river? Specially in places where corridor river is below EG. If there is some tool like cut?
View 4 Replies View Relatedhow to have exisitng cross slopes display on a bank of corridor cross sections...I see lots of posts on this but I am having trouble finding the answer. The link below from Add a section view grade label only adds "A" slope label.....I want all of them in all of my sections.
[URL]
I got this error opening a .dwg in C3D 2012.
Win 7 Enterprise SP1 64 bit
Intel i7 3770 @ 3.40 GHz
16 GB RAM
Civil 3D 2012 SP2
I have made all my sheets through the Plan Production wizards. When I go to sheet set manager, and select publish to pdf, i get an error saying the following:
ERROR: Layout not found..By using one tab per drawing, seems to publish ok. But we want multiple tabs per drawing, so not really any use to us.
I'm having a problem opening AutoCad Civil 3D 2010.
When I click the shortcut Windows starts configuration and then I get the following error message:
Error 1308.Source file not found;C:autodeskAutoCAD Civil 3D 2010
x86C3DProgram Files
ootCommon Files FolderAutodesk
sharedAdLM|R1en-UShelpBRWstylecommons.css.old.
Verify that the files exists and that you can access it. Needless to say AutoCad wont open all I get is Retry or Cancel, selecting.
Retry just gets the same error so when I Cancel I then get "Are you sure you want to Cancel" which I select and then I get the message Fatal Error during installation.
This is a downloaded install from Autodesk and I dont have discs available.
DWG TruView,Autodesk Vault 2010 and Autodesk Design all installed OK.
System detail's; OS is 64 bit Windows Home 7 Ver 6.1.7600 with IE8
CPU AMD Athlon 11 P320 Dual Core, 4 gig RAM,500GB HDD running on a new Toshiba Laptop.
I've looked around at various forum's without success.A couple of sites offer what they call a fix but it turns out to be registry scanners.
I'm having problems with Autocad Civil 3d 2012. I'm building a corridor of a curb gutter and sidewalk with a daylight of 2:1 on top of an EG surface. The corridor works for about 3/4 of the length but the last section won't connect the daylight to the existing ground surface. There are multiple sections of the corridor with different assemblies.
Here is a more detailed error report:
Type: Error
Date: 11/5/2012
Time: 9:15:06 AM
Source: Roadway
User: engintern4
Description: 6+80.00': Failed
Point Outside Surface.
Offset: -7.542'
Elevation: 85.776'
Corridor: CURB-GUTTER-SIDEWALK CORRIDOR
Baseline: Gutter Alignment
Alignment: Gutter Alignment
Profile: Gutter Profile
Assembly: SIDEWALK-CURB-GUTTER-DAYLIGHT
Assembly Baseline:
Subassembly Group: Group - (3)
Local Subassembly Name: DaylightMaxOffset
Global Subassembly Name: DaylightMaxOffset (Left) - (50)
Assembly: C:ProgramDataAutodeskC3D 2012enuC3DStockSubassemblies.dll
.Net Class: Subassembly.DaylightMaxOffset
Source: AeccDbMgd
I get about 33 of these errors each time the corridor rebuilds. I'm not sure whats going on, the corridor has targets set for the surface and still won't connect to it.
I am getting this error when I am trying to create a surface from my corridor. Instead of just defining a surface along my corridor it is trying to connect all contours lines between different parts of the corridor
When creating the surface I define 2 surfaces, one with overhang correction as top links with links data set as top, and a second with overhang correction as bottom links with links data defined as datum. I have then defined the boudaries using add automatically-daylight. I have followed this procedure for 5 previous corridors with no issues (ie the surface matches the corridor) so is there anyway I could have done something different.
I think I just haven't done this in a while and can't find the right setting.
I have existing sections.
I have section views.
I created a corridor.
How do I add the corridor section to my existing cross-section in the section views?
I can view them in the corridor section editor. But I should also be able to add the corridor section to my section views, right?
To plot them, do I NEED to do this through Sheets Sets? I don't have experience with sheet sets yet.
I don't use Civil 3D often enough anymore. Still learning much about the new interface and pulling a design together.
Using Civil 3D 2012 SP 1 on Win7 Pro 64-bit.
Is there any reason why a corridor model would not be respecting the manually entered super elevation values in the alignment? I have several stations that should be calculated with even super elevation values, but they aren't. For example, at station 0+080 on my alignment the left crown should be running at -3%, but it is actually being calculated at -2.47%. It isn't just one station; it's most of them. No overridden stations, vertical targets, etc in the corridor. Just a fairly straight-forward align (hor/vert) with super, simple assembly (two lanes, shoulder, daylight), simple corridor.
I'm getting several messages saying "value on wrong side of alignment" when I rebuild my corridor. I've checked the two target alignments that I'm using and they are on the correct side.
Civil 3D 2014
I have created a surface from a corridor. I set the boundary of the surface to the daylight of the corridor. In some areas of the corridor the surface does not triangulate see attached.
View 2 Replies View RelatedCopy a corridor successfully? I'd like to try this just a little worried about the explosion of evil this may cause to my Civil 3D session.
Even all the properties of the corridor setup from one to another would be useful. I'm building one corridor and an 2nd one that matches everything except I need to replace my Assembly with one meant for stripping.
My corridor surface is not matching my corridor top links. see attachments. this is affecting my volumes!
The section-plan(surface red).png is showing the section editor and the plan view. the red highlighted line in section is the corridor surface and as you can see in plan view the surface is incorrect and wiggly.
The pdf is all my sections with the red linework being the corridor surface.
C3D ver 2012
Win 7, 64bit
I'm trying to create an all new existing surface over existing ground. I have a TIN surface of the EG, and I have drawn overlay splines that describe the new surface, but how to go about creating that design surface.
It is a compound surface, open on one end and closed all around on the other, somewhat like a half of a football stadium, but with an irregular upper edge because I am needing to figure out cuts and fills to manipulate the EG into this new surface without costly major terraforming. There is about 40-50' vertical elevation between the "field" and the upper rim with a generally constant 7-10 deg. slope all around. I'm just at a loss to figure out how to approach this project, and am quite new to Civil 3D.
Civil3D 2013
MacBookPro 17 - 2.4GHz Intel QuadCore i7 (Late 2011 build)
Microsoft Windows 7 64bit
350GB Bootcamp volume
User received this error after trying to open a 2nd drawing after receiving a fatal error unhandled excpection e0434352h 7c812afbh.
New error messag is: Method not found: "Int64 Autodesk.AutoCAD.DatabaseServices.ObjectId.get_OldId()'
I have an error that started appearing in my VBA programs since we upgraded to AutoCAD 2012. This problem never occured in our previous releases. The program is supposed to loop through all entities in paperspace and check for entities that are a acBlockReference object.
Below is a simplified version of my program. I get an Element Not Found error on the line noted. Again, this has never happened in any of our previous versions of AutoCAD. Just started with 2012.
Sub Test
Dim blkref As AcadBlockReference
Dim entry As Variant
For Each entry In ThisDrawing.PaperSpace
If entry.EntityType = acBlockReference Then ' <-This is where the Element Not Found error occurs
msgbox entry.name
endif
next
end sub
I'm getting this error "Run-time" error '48' "File not found: *****.arx" calling functions from VBA (Autocad 2011 64b).
note that same code (VBA & ARX) works fine on 32b env.
I am building sub-assembly, I just want to know if there is any example or tutorial on how to add target parameters to sub-assemblies.
View 6 Replies View RelatedI´m having som problems to publish a part in to the Content Center. It´s the first time I´m doing this.
The part is made with parameters and is a little bit more complex than a bolt.
The problem is that I got this message: "There are external dependencies found in the document. Please remove the dependencies then proceed with this comand."
Error 1308 Source File not found inventor professional 2013
View 1 Replies View RelatedI have created a bin/vat/tub using sheet metal. I started with a contour flange. I then copied the sketch and pasted into a new sketch off the flange for a contour roll feature. Then a flange, roll, flange, roll, flange and roll. My trouble starts at the last flange. I'm trying to construct the flange exactly as I have created the features before. I set the distance, select the profile (it shows the flange on the screen), hit apply and that's when my message shows up. "Non-tangent curves found in path: flat pattern cannot be correctly created. Edit sketch and add constraints to the curves. The sketch is fully constrained according to the lower right hand corner and the auto constrain button.
View 2 Replies View RelatedI am using OffsetTaget.isValid in my subassembly.But i realize that when i put this formula it checks the whole drawing for that target and if the target polyline exist even a piece of polyline in the drawing then C3D considers it for all sample lines.Is ıt possible to be able to check each single sample line if it is going to intersect that target polyline or not?
Civil 3D 2014 x64
Windows 7 64-bit
16GB RAM
i have just spent 8 hours today trying to find a link that will vary target a poly line that i have set. i cant seem to find the link that will do what i need as per the attachemnt. the section between the edge of the foot path and the start of the fill/cut slope needs to be variable
i know how to set all the targets but this link seems to be a fixed length.
What i want to do is ; i have a corridor with both right/left sides ending with linktosurface with fixed slope.In some sections my existing surface is not wide enough to get intersection with link to surface with fixed slope. So i want to use this "conditional horizontal target " if my surface is not enough wide for intersection then just intersect or go to the edge of my existing surface. But i learned that surfaces cannot be used as an offset target with that subassembly.
View 9 Replies View Related