I drew in a water line that had an arc in it, the "W" symbol in the line (or arc rather) is upside down. i've tried the reverse command, tried re drawing the arc both ways, tried re loading line types, is there any way to fix this?
View 9 RepliesI have made line types with text and need to reverse the direction that the text reads. The text autocorrects based on UCS north. The UCS in the drawing is rotated 90 degrees so line text reads upside down. I type in the reverse command but the text does not change.
View 1 Replies View RelatedI have created a linetype with the text GAS OPTION in it. The line is continuous with a break around the text. In a straight line the linetype works fine (breaks around the text etc). However, when I use a polyline and spline the line for a curved line the text aligns with the direction of the line at the start, but when the line bends, the text suddenly changes direction and reads in the opposite direction. It looks like AutoCAD is trying to keep the text upright rather than following the direction of the line. When the text changes direction it also changes its insertion point and overlaps the continuous part of the line. I have 2013 AutoCAD.
Here is the string I used for the linetype.
*GAS_Option_LINE,Gas line ----GAS OPTION----GAS OPTION----GAS OPTION----
A,8,-15,["GAS OPTION",STANDARD,S=2.54,U=0.0,X=-2.35,Y=-1.27],-12
i have problem in changing line directions that i'm using in my alignment.like buttom figure.
View 6 Replies View Relatedhow to have an option for the landing direction at the end of a leader line, or a way to edit one that has been created.
View 8 Replies View RelatedI have a special ditch profile that I'd like to use a linetype with arrows on. Currently, it shows the arrows going up station with my mainline profile. i.e. now water does flow uphill...
How can I flip this line?
Now, in my understanding, the flow arrow should either be rotated 0, or 180 (pi radians). But clearly, some of them like to have their own mind about things, and decide on some other rotation. It seems that on the steep slopes, the arrows go a bit skew.
I think the skew is related to the actual elevation difference of the segment, rather than the steepness of the slope. A long segment with 15% slope has a worse skew than a short segment at over 30%, presumably because the elevation difference from the start to the end of the segment is larger.
Can you reverse the direction of an auto feature line generated from a corridor in C3D 2012?
View 4 Replies View RelatedI have a path with a smooth point. The two direction points form a direction line with any non-45-degree-angle - say 11.8 degrees. I want to drag one direction point while keeping the angle of exactly 11.8 degrees.
Is there a key combination for that (Mac OS)?
I have cut several sections at different points along a road alignment. The sections are cut facing the same direction as the alignmnet. Is there a way to reverse the section direction without changing the alignment direction?
View 6 Replies View Relatedi've made a serpantine curve that starts from one line of alignment and end on the other line.
i wanted to know how can c change alignment direction when these two feature line and alignment meet each other in order to change the alignment path?
How can I change direction of a line feature? Have any redy default command to do it?
View 8 Replies View Relatedhow to set line direction by N,E,S,W by degrees, minutes and seconds.
i.e.. drawing a plot plan laid out by a surveyor.
Must I convert to degrees for polar coordinates or is there a way to directly insert these angles?
I want to force the Multileader landing to go left when the program wants to automatically form it to the right. How can you choose/change the direction of the landing line and side on which the text will be placed.
AutoCAD 2011
I have a drawing of a stone railing section and I have to change direction in the run direction of the baluster panel. Is there a way that I can move the details without changing th Y direction of the details. Please refer to the attached CAD file for details. I am trying to avoid having to redesign the panels if possible. railing detail.dwg
View 6 Replies View RelatedToolspace > Settings > General > Label Styles > Line
When I create a line label, one of the components available is “Direction Arrow”. This component is not available for “Curve” labels. I would really like to use C3D labels to indicate direction (I realize curves don't have a 'direction', but I don’t mind manually flipping and reversing the arrow). Is there any other label option in C3D that will draw a direction arrow for curves?
is there is any way to reverse the alignment direction
View 3 Replies View RelatedI need to be able to do a slope analysis on a surface, but I need to have it calculate the slope in a direction - east and north. Any way to do it? Maybe even if there is a quick way to apply slope labels to a surface based on a grid - say the slope from N0.00, E0.00 to N0.00 to E 25.00
View 9 Replies View RelatedIs there a way to change the direction of a Label? I want all my text facing the same direction and some of my Labels for contours are turned the wrong direction.
AutoCAD Civil 3D 2012 SP4
Windows 7 (64)
I'm currently working on a cross section plan and was wondering if there was any way I can change the direction of the cross section view. I'm currently just using 2 sample lines, so just 2 views are needed. My problem is that it seems like one cross section...the view is facing upstream and the other sample line, the cross section view is facing downstream.
Is this normal? How come both cross sections don't face the same direction? So with one x section it's in a East-West direction but the other is a West to East direction.
HP Compaq 8100 Elite
Win 7 Pro SP1 - 64Bit
8GB RAM
i7 860 @ 2.80 GHZ
AutoCad Civil 3d 2012 SP1
Can I reverse the direction of an existing horizontal alignment line in C3d 2011?
View 9 Replies View RelatedChanging alignment path in my drawing,how can i do that? There is a pic too.
View 1 Replies View RelatedHow to get my invert labels to reference construction north rather than actual (surveyed) north?
C3D 2012, SP1
Win7-64 bit
I imported 5182 points (in the NEZ format) into my AutoCAD Civil 3D 2013 (English Metric) and then created a Surface from these points (Style: Contours 1m and 5m (Background)). I selected a polyline => Alignment => Create Alignment from Objects - see the attached file. How can I verify the direction of the alignment I just created?
View 2 Replies View RelatedI have a pipe network (data shortcut) showing in the profile.
The pipe network was designed from station 98+65 to 100+00.
But the first pipe (from station 98+65 to 99+30) is shown going from station 99+30 to 102+60.
The pipe has a lenght of about 65' and some how it is being projected incorrectly.
The profile is shown going from right to left.
See attached image.
Windows 7 64-bit
Civil 3D 2012 SP2
I can't figure out how to reverse the flow direction on my pipe so I was going to just redraw it but after I delete a pipe and rt click to edit network the "add pipes and stuctures" won't let me add anything. I'm just guessing I need to reverse the flow direction because my invert out and invert in elevations are backwards in the profile. I'm working in Civil3D 2012.
View 6 Replies View Relatedis there maybe an error in the XSL?
Here is my alignment, correctly labelled in South Azimuth:
Before customising, the Alignment_Curve report gives me this:
Is it possible to have pipe flow direction method set to "by slope" by default when we creating new pipes?
View 5 Replies View RelatedI am close to getting my general legal the way i want. The only thing i hope to change now is the way the bearing is shown. it currently spits out as 89degrees 50minutes 50seconds. I simply want to add a space between the number and callout.
Example:
89 degrees 50 minutes 50 seconds.
I cant seem to find this setting.
I would like to reversing a Boolean operation if an error happens.
I have two solids that when I try to perform a Subtract Boolean Operation gives me an error. When the error happens I lose both solids. I would like to be able to reverse the subtraction in an event of an error so that I still have both solids.
Dim Solid_1 as Solid3d = CreateSoldFromPl(plinePoints1)
Dim Solid_2 as Solid3d = CreateSoldFromPl(plinePoints1)Try
Solid_1.BooleanOperation(BooleanOperationType.BoolSubtract, Solid_2)
End Try
I am trying to create a new linetype using arrows to show the direction of a flow. I can get the outline of my arrow head to save as a shape, but have not figured out how to save the hatching to show up in a linetype. I need the arrow head to be shaded in solid. Also is there any downloadable linetypes out there for Civil 3D?
View 5 Replies View Related