If I have calculated the superelevations and then edit the alignment (for example,I modify the length of spiral), the superelevations doesn´t recalculate. Why?
The guitar (superelevations) in profile view is old. If I load again the style profile view, the data are the same about superelevations.
Autocad Civil 3D 2014 +SP1 Quad Core Intel i7 3770-cpu 3.40Ghz. ssd samsung 840 pro 512gb+ssd samsung 840 pro 256 gb+1tb hdd 32gb RAM 1600 Mhz. nVidia Quadro 2000. Win 7 Pro 64bit
I have created existing and proposed surfaces in Civil 3D 2008 and I'm trying to create a volume surface to produce a cut & fill map. The problem I'm running into is everything I try to follow mentions choosing Elevation Banding (2D) as the style. The only style I have to choose from is Standard. Does the Elevation Banding (2D) style normally come with the program? Or is this something you have to create?
Recently I have purchased the above software to be installed on a 32 bit PC. However, the USB installation that came is 64 bit and the free trial on Autodesk website, although it offers the 32 bit, is also 64 bit.
It seems that the 32 bit version does not exist. Is there a way around this? I was hoping to download the 32 bit trial version and using the serial number and product key of the 64 bit.
Does name property of a page item appear anywhere in the user interface in Illustratpr CS6? I thought it would be the name you assign to it in the Layers palette, but it does not appear to be.
In my drawing, I inserted a raster image file. I converted it into a block so I can modify it and I scaled it like this:
img_before.jpg
I saved my drawing and I close AutoCAD, but when I open AutoCAD again the image shown on the drawing file is not the same image that I had inserted previously.
img_after.jpg
The image shown is one that I had inserted before the first one but I had erased it from the file because I had to crop it in photoshop to reinsert it again.
I used the purge command to purge the block, I used the image command and i detached the image.
But the image says "unreferenced" when I do the "image command" even though it has the right location and folder. I don't know what to do anymore.
I have a problem with exporting layers from dwg to pdf. Problem is that i can export (or print) drawing but i missing some layers in layer manager in pdf. I have drawing with 150 layers (from other co-workers) but only mine 4 layers doesn't appear. I have check in ACAD in layer prop manager if they are plottable but this is not a problem for content from those 4 layers are exported in pdf but not in layers they have to be (those layers are missing)!
I use ACAD 2012
edit: i found out that layers doesn't appear because contetnt on them are only blocks. for eg. block is on layer 1 but contetnt of block is on layer 2 so i see only layer 2 in pdf but not layer 1
When I try to create a new font style using the standard Autodesk Swiss fonts, I get the message "font file doesn't exist". I can see that the fonts are in the AutoCAD fonts folder and that I have a file path set to that folder.
I believe a dwg I am trying to access is affected by the acad.vlx virus as an alert comes up to check autodesk for solution (ID: TS13717811) however the published solution doesn't seem to work for the latest version of AutoCAD LT 2012 as it asks me to access a file in the support folder which doesn't exist on my system.
i have aprblem with the main icons of the ribbon, i install the program and it works correctly Suddenly the user interface converts to the normal autocad i tried to restore the ACAD.CUIX and doesn't work.
i have Win8, the version i have of the program is 2014 and the problem also happen on autocad architecture.
I have a problem with my fonts in adobe, because there is 1500++ fonts in my font book that already installed, but ,if i open my photoshop there is just 26 fonts that exist?
I've got a problem with a vertex on my model. When I go into the skin modifier or edit poly, this one vertex doesn't seem to exist. It doesn't show up and I cannot move it, yet in the skin modifier it is being affected by something. How can I get this vertex to reappear without completely borking my model's skinning?
I have a problem with my superelevation. everything is calculated accordingly but when i build my surface from corridor after i have calculated superelevation it does not show the results. Even my cross sections view still show a normal assembly cross section. It happaned on both C3d2011 and ad C3d3013.
Is there a way to retrieve superelevation values from Alignment properties to show on, for example curve tables?. I would like to display the super information along with curve geometry information.
but I don't know where, and I just want to create a simple assembly with a slope and delta X and having a lane outside superelevation for the both side.
This is my aplicattion in Civil 3D 2014. URL....It´s a tool palette that checks the design criteria (for alignments,superelevations and profiles) according to Spanish rules.My program changes the name of each superelevation curve,for example:
---> With superelevation tool own of Civil 3D (Cuve.1,Curve.2,Curve.3)
---> With my program: (VisorNET Curva.1,VisorNET Cuva.2,.....)
If I calcule again Superelevations using Superelevation button (Calculate/Edit superelevation)of Civil 3D, Civil 3D doesn´t change the Superelevation Curve Names and appears again (VisorNET Curva.1,VisorNET Curva.2,...).Superelevation CurveName property doesn´t exist in settings:
URL....and there isn't a name template. I would like to have this property (read and write----get and set) of settings.Then, I could re-write the default Superelevation CurveName format. (name template)
I am working with SAC , and cant understand how that superelevation works, how to make my models work in CIvil 3d in superelevations... how to build it properly in SAC. I would rly love to get .pkt file with working model as example , or at least get some usefull tip.
I am currently trying to design a roadway with a reverse curve in it. I am having trouble getting my corridor to model my assembly correctly as it is showing the roadway as the generic assembly and is not adding the superelevation that is shown on my alignment. I have done the following:
1) created an alignment with superelevation wizard - superelevation diagram shows up correctly
2) Created a profile for this alignment
2) created an assembly (Road layer is LaneSuperelevationAOR) in which the right lane is set to use SE on the right outside lane and the left lane is set to use SE on the left outside lane
3) Created a corridor with the assembly and set the width targets to the offset alignments (I.e. the lines that are the edge of pavement)
The corridor does not show the superelevation values based off of the alignments superelevation that it has calculated. I did get the supers to show when i tied the Future EOP to the existing surface, however i do not want it to tie in, I want it to just show the values that were calculated.
Is there a way to get this to show without referencing an additional profile? Also, on my first curve i want to keep the right side at a -2% slope and raise the left side to 2% slope (RC). Is there a way to limit the calcuations to only use a reverse curve?
I found super elevation labeling for profile, but not for alignment in plan view. Is there a way to label alignment, f.x. in critical points of super elevation automatically?
In my corridor I have used superelevation. In a horizontal curve which has a cross slope of 4.5%, I have an intersection. To allow for a smoother ride through a few lanes in the intersection I want to change the cross slope from 4.5% to 1%. I was planning on doing this by using a Outside Lane Elevation Method of a Profile. However, it appears that my super has precedence over my profile. Is there are way to make this work?
I have an alignment I need to edit that has a reverse curve. The first curve was made with the "Floating Curve (from entity, radius, through point)" and the second with "Free Curve Fillet (between two entities, radius)"
When I delete one or both curves i lose all the superelevation data beyond the editing location due to the temporary spit in the alignment. The superelevation data is all manual. This is a trail and the super is based on drainage not curves.
how to edit the alignment with a temporary split and not lose the superelevation data? I have not found a way yet to remove the reverse curves and not have a temporary gap.
Is there a way of adding superelvation data such as full superelevation cross slope to an alignment curve label in plan view?
In my case we add a label for each horizontal curve with critical curve data such as PI Station, Delta, Degree of Curve, etc... but I can't seem to find a way of adding any superelvation information to the plan view as a label. Ideally I would like to be able to add the maximum cross slope value and superelevation critical stations to the label.
There is a way of adding the superelevation critical stations a labels to the alignment similar to how PC's or PT's are labeled, but it does not give the cross slope value.
my surface is way through the in and out transition of my superelevation. the waves are dependent on frequency (ie if i change from 1m to 5m the waves get longer.
I'm attempting to use the Superelevation tool on an interchange. I have 4, 1-lane ramps that I need to apply superelevation to. The three issues I have (so far) are:
In the Calculate Superelvation Wizard...
1. In Roadway Type, I don't know what to choose, I'm leading toward Undivided Crowned (center Baseline ) because my assembly (as of right now) is set up as an undivided crowned roadway (with the crown on the west travel lane edge). Which Roadway Type I should choose (for a 1-lane Ramp with different shoulder widths?)
2. Moving on to the the Lanes category doesn't matters. I uncheck symmetric Roadway, hoping I can choose "0" for the number of lanes on the Left, or at least put the lane width down to "0" but can't do either. I uncheck the Symmetric Roadway and it still makes everything symmetric (it acts as though it is still checked?) I only want to show a single 15' lane. (I even tried to use undivided planar, and put both lanes at 7.5'each, but then I still have shoulder issues...)
3. Move to the Shoulder Control. Why doesn't it give me the option to do different shoulder widths? On ramps it is very common (at least in Wisconsin) to have an 8ft shoulder on the right and a 4ft shoulder on the left. How can I type in 2 different shoulder widths.
In attached file the normal cross slope of secondary road(AB) is 2% Right to left (Right higher). and for primary road cross slope is 2% Left to Right (Left higher). I produced this junction using intersection wizard and cross slope of secondary road only starts changing from start of curb return to match the long slope of primary road. Is this possible to increase this transition lentgh on secondary road to create smooth contours.
in case of replacing a component in an assembly the present item number in (structured) BOM table is reassigned through a new one. This cause a lot of troubles in our firm, because this requires rework of item numbers after each replace action. I expected that especially in case of an replace of all occurrences, the item number is kept. Is there a setting to keep item numbers after a component was replaced?
Inventor Professional 2011 Windows 7 Enterprise 64bit Dell Precision M4500 Intel(R) Core(TM) i7 CPU Q 820 @ 1.73GHz 8 GB RAM
I have profile sheets I set up using our template. If I plot the layouts one at a time. I can see the existing grade line in the plot. If I publish all of the layouts at once. The existing profile doesn't plot.
I've checked the layer freeze setting and made sure there is a defined page setup to use in Publish. It's the same setup they plot individually with. I get the same result if I plot directly to our Toshiba printer or to PDF using the CutePDF driver.
