How to get these crop circles where two pipes join, from time to time? (See attached inside red rectangle.) The pipes are connected at the same elevation in a straight run, but we need a vertical bend there, and hence the Null Structure.
View 1 RepliesPipe network storm pipes: Fairly new to Civil3D and trying to set up parts list for the storm sewer pipe and would like the plan view to appear as it does currently. We use a polyline for centerline of pipe, similar to dashed linetype but line and space are the same, width set to pipe width.
View 1 Replies View RelatedI created pipe network for my storm drain project. I have located all the structures (manhole) to all angle point of my alignment as required. Also I "insert" manhole every 400' per local code requirements using the command "network layout tools; structures only. My problem is I couldn't find the tools how to trim the pipe that pass through the manhole. Please see attached pdf file.
View 1 Replies View RelatedOne of the things I seem to struggle with is being able to depict a single pipe when it needs to be shown in one profile as a crossing pipe, and another profile where you you show a lenghwise slice through the pipe. I end up tracing the pipe with eliptical objects where I'm cutting across the pipe and setting up more for the lengthwise/sideview of the pipe. Is there a way to have two different styles for the same pipe, one for a cross cut and one for a lengthwise slice?
View 1 Replies View Relatedis there a way to include the pipe min/max cover as part of the str/pipe label?
Civil 3D 2013 SP1, Win 7-64 bit
12GB RAM
Using Network Layout Tools, can you attach a pipe to a structure in a different Pipe Network? 2013 Civil 3D
View 6 Replies View RelatedHow to join 2 alignments which are continuing a same road? Is it even possible ?
I have tried to explode them into polylines > join the polylines and then reconstruct the alignment again but it crashes on everything longer than 15 miles
Drawing: line, arc, line.
arc was defined with line's end points and radius, so I'm positive that this drawing is continuous.
Steps I take:
pedit
click
do you wish to turn into polyline
y
j
Select objects: 1 found
Select objects: 1 found, 2 total [enter]
Select objects:
0 segments added to polyline
[enter]
I had no problem turning other arcs into polyline...
I am joining plines on the same layer, etc. I was taught to use PEDIT-Join but noticed that I can do the same function with just the JOIN command. Is there any difference? Is one better/safer to use?
View 7 Replies View RelatedI have two different assemblies, one has a normal batter slope to a table drain or embankment and the other is a kerb and channel. Refer attached.
When you apply these two assemblies in a joining regions, I get both assemblies at the same point, which causes the corridor surfaces to incorrectly triangulate.
The command to JOIN two overlapping anchor points as a SMOOTH join is not working (at least, on Mac).
"The join option only results in a corner join regardless of whether you select anchor points to join or the entire path. However, for overlapping anchor points, if you want the option to select a smooth or corner join, then use Ctrl+Shift+Alt+J (Windows) or Cmd+Shift+Option+J (Mac OS)."
Can't seem to figure out the correct style menu to access in order to turn the pink circles that represent (I believe) the station markers OFF when I go to view my corridors in object viewer or section editor...
View 1 Replies View RelatedI have a large amount of "ellipses" in a Civil 3D 2013 drawing that were created as "circles" in Cyclone 8.03 (the laser scanning software from Leica-Geosystems). I need to work with circles so I can label the diameter of each in my drawing. Is there a way to automatically convert these ellipses, that have the same exact minor and major axis, into circles? Other wise I will have to reapeat the work in Civil 3D using the same point cloud!
View 8 Replies View RelatedI have noticed since using c3d 2013 circle "markers" appearing at the curves on my alignments. I can't find the control to change / turn off?
View 1 Replies View Relatedhow to make the circles on my parameter locations smaller? What controls this feature?
Windows 7 x 64
Nvidia GeForce GTS 450
8 GB Ram
Intel Core i5-2310 @ 2.90 GHz
v. F.107.0.0 AutoCAD Civil 3D 2012 SP1
I'm trying to make a logo. Circular logo with an inner ring maybe 4 px wide and 15 px inside the rim of the outer circle.
Basically I want a blue circle with a yellow inside ring. What's the best way of doing this? The only thing i can think of is: creating a blue circle marquee, and then another (trying to estimate a new circle size and change the color) that is yellow, and then making another smaller blue circle inside the new one. That's just ugly.
I tried the edit/stroke but that just gave me a stroke around the outer circle; it didn't put a ring inside the circle 15 px down.
Also I tried to contract the original circle by selecting it, then Modify/contract. That's got me a selected ring, inside the circle. Now how in the world do I make that little ring yellow? It just remains selected and I can't seem to find a way to color it.
I created a pipe rule and applied it to my 6" HDPE pipe in my parts list. The rule is followed close but not exact. Here it is:
I created a "cover only" rule for my 6" HDPE pipe. I have the maximum and minimum cover set to 3.50'. I have it the same so it will draw my pipe 3.50' deep. I don't want it to vary. It for drawing in existing underground power so when we cut profiles and sections the existing power shows up. We want it to show up 3.50' deep. I created a label style for my pipe that tells me start cover and end cover of the pipe so I can see it right there on the screen. The numbers range from 3.50' deep to 4.70' deep.
Why does the pipe not get drawn in exactly 3.50' deep?
When I create a new pressure network in 2014 - I have only Tees & Elbows available - Where are crosses? I need a 4-way cross at an intersection, C3D seems to include just the other two types I listed.
View 3 Replies View RelatedI have this block called gate valve. The base point is at the middle of the block. When I use this block as a style and insert it in profile it always places itself down low on the pipe. As you can see the grip is way above the top of the block and I have to move it into place anytime I use one. If I change the pipe inverts the gate valve block style lowers itself once again and I have to move it up into place. I have changed the base of the block but it makes no difference.
This is how the structure look in the object viewer. Notice the one on the right is the block that needs to be raised, however in the viewer it shows placed correctly.
Any way to label a pipe part way between structures? I would like to be able to label a sanitary line where a service ties in with the main line invert.
C3D 2013
My boss has designed a gravity project that has 21" PVC. Civil 3D 2010 only has 20" PVC, not 21". He basically said 21" PVC exists (JM Eagle) so make it happen. So how exactly can I add a new size to the Parts Catalog under PVC?
Windows 7 Prof w/ SP1, 64bit, Xeon 3Ghz, 16GB
Civil 3D 2013
Version Civil 3D 2013....
A pipe network has been created & labeled. All pipes labeled correctly except one. The material for 15", 18", 24" RCP pipes labeled "RCP" but all the 12" pipes labeled "Reinforced Concrete Pipe". So I know I need to change the Material of the 12" pipe to read "RCP". I was hoping to just go to Pipe Properties & change it there for this dwg but it doesn't change.
I was thinking it might be in the part xml file but why would some label "RCP" and the 12" didn't? The Parts Catolog used in this dwg is the default from Autodesk. Also, in the Part List, Material is greyed out. That's the first place I went to change the Material.
I'm in the process of creating content for "pressure Pipe networks". I have created a number of pipes (HDPE, PVC and steel, sizes ranging from 20mm to 200mm). I have also created a number of Tees (Equal and reducing).
My question is.
If you draw in pressure pipe say 90mm ø and the insert a fitting say a 90x75x90 reducing Tee into the line. Then you wish to extend the pipe from the 75mm ø branch, it does not pick up it should be a 75mm pipe but defaults back to the setting (90mm) that you drew the original pipe line in, you have to change the default pipe type to 75 before extending the 75mm pipe from the Tee.
Below I have included a couple of screen shots.
I'm drawing existing SD pipes and trying to put in rim and inverts of the existing structures. Sometimes it won't let me raise an invert to where it really is. It only let's me raise it so far. It may be a rule but it doesn't seem to be a rule I can change.
View 4 Replies View RelatedI have multiple profile views with a pipe network. In a number of cases, I have a pipe that extends to the end of one profile view and continues on the next. I can label the pipe on one profile but not on the other. Is there a way to add two labels to the same pipe - one label on one profile view and another label on the other profile?
View 2 Replies View RelatedTrying to make some changes to improve reading. The pipes are going to center of structure and would like to change the appearance but maintain the lenght to the center or in last case to the structure wall.
The image explains the 'problem'. Red line should be the correct appearance
There is a way to correct the position?
I've set the start and end locations to be at the structure inner wall and applied rules but the invert elevation is still as if the pipe ended at the center of the structure. Did I miss something or does this not do what I think it does?
View 1 Replies View RelatedI have lost the ability to create a pipe network in a single drawing. Sorta. I can create a pipe network, and label it, and see it in my toolspace, but it won't display it for any style in any format. I can bring in a data reference and label those, but can not see pipe or structure outlines or anything to that end. I have tried to recover, audit, purge. I am at the end, currently creating the pipe network, data referencing it in, and then just drawing lines between the labels.
View 9 Replies View RelatedI'm using C3D 09 with all the updates. OK, now that those are addressed, I am having an issue with my pipe hatching dissappearing when I connect it to a structure. See the two attached pics for clarity.
View 4 Replies View Relatedhow do I use Civil 3D to do basic pipe analysis computations? For example, I give it the slope, material, etc. and it spits out the flow velocity, flow depth, slope min, etc.
All I want for now is a basic tool for sizing pipes without all the bells, loops & whistles. I can learn the fancy pipe networking stuff later.
When labeling pipes, the lengths and stations do not always match. this appears to be related to a rounding issue. for example, the first pipe may start at 0+00 and have a length of 50.69167397’. The reported station in the structure label (using “normal rounding”) is naturally 0+50.69, as anticipated. The upstream pipe has a length of 43.36435901’, resulting in a total length from 0+00 of 94.05603298, resulting in a station of 0+94.06. However, the rounded values of the lengths (c’mon, nobody reports lengths to the 100-millionth) labeled on the pipes (50.69’ and 43.36’) total an expected station of 0+94.05.
I have tried all manners of “rounding” in the label styles, but it always falls down in one situation or another. I have also tried setting in the network and pipe “Feature Settings” for distance to a locked accuracy of 2 decimal places, but that does nto seem to do it either.
So, the question is, is there a way to resolve this issue without having to move one of the structures 0.001’ to resolve the mathematical parallax?